Euroboor ECO.36+ User manual

Serial number:
Date of purcha
se:
/ /
Don’t forget to register your machine at:
www.euroboor.com/register
[ only when registered you benefit from extended warranty ]
User manual
V 1.1 EN
Low profile magnetic drilling machine
with 2-way electromagnet
ECO.36+

2
Congratulations on purchasing this premium magnetic drilling machine. At EUROBOOR we strive to
exceed our customers’ expectations b developing and providing premium and innovative portable
drilling and cutting solutions. We believe that a professional like ou must be able to rel on a
professional supplier. Which has led us to become a major pla er in the industrial world, with our
own factor and several offices worldwide. All because we have alwa s listened to our customers
and to the demands from the market.
Our vision is focused on developing innovative portable tools that add value for our customers and
facilitate them in their dail work. We never lose sight of sustainabilit , time savings and cost savings.
Enjo our new machine!
Before operating our new magnetic drilling machine, please first read all instructions. You find the
instructions in this manual and on the warning label on our machine. With proper use, care and
maintenance our machine will provide ou with ears of premium drilling performance.
TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND ALL INSTRUCTIONS
To view all our offices and their contact information please visit: www.euroboor.com

3
Table of contents
ECO.3 + ....................................................................................................................................... 1
Table of contents ......................................................................................................................... 3
1. Safety ....................................................................................................................................... 4
1.1 General safet instructions ........................................................................................................... 4
1.2 Specific safet information ............................................................................................................ 6
2. Description ............................................................................................................................... 8
2.1 Intended use .................................................................................................................................. 8
2.2 Description and features ............................................................................................................... 8
2.3 Case content .................................................................................................................................. 9
2.4 Serial number ................................................................................................................................ 9
2.5 Technical data.............................................................................................................................. 10
2.6 S mbols ....................................................................................................................................... 10
2.7 Environmental ............................................................................................................................. 11
3. Preparation & adjustment ...................................................................................................... 12
3.1 Assembl ..................................................................................................................................... 12
3.2 Prior to use .................................................................................................................................. 18
4. Using the machine .................................................................................................................. 20
4.1 Carr ing handle ........................................................................................................................... 20
4.2 Control panel ............................................................................................................................... 21
4.3 2-Wa electromagnet .................................................................................................................. 21
4.4 Switching motor on and off ......................................................................................................... 22
4.5 GYRO-TEC safet .......................................................................................................................... 23
4.6 Power surge and fluctuation protection ..................................................................................... 23
4.7 Carbon brushes ........................................................................................................................... 24
4.8 Tool lubrication ........................................................................................................................... 24
5. Working with drilling accessories ............................................................................................ 2
5.1 Annular cutters ............................................................................................................................ 26
5.2 Twist drills .................................................................................................................................... 28
. Maintenance .......................................................................................................................... 29
7. Trouble shooting .................................................................................................................... 31
8. Exploded views & spare parts list ............................................................................................ 33
8.1 Exploded views ............................................................................................................................ 33
8.2 Spare parts list ............................................................................................................................. 36
8.3 Wiring diagram ............................................................................................................................ 38
8.4 Warrant and service .................................................................................................................. 39

4
1. Safety
1.1 General safety instructions
Do not use this magnetic drilling machine before ou have thoroughl read and completel
understood this manual, specificall the “General safet instructions” and ‘’Specific safet
information’’ , including the figures, specifications, safet regulations and the signs indicating
DANGER, WARNING and CAUTION.
WARNING: When using electrical tools basic safet precautions should alwa s be followed to
reduce the risk of fire, electrical shock and personal injur .
Please also observe the relevant national industrial safet regulations. Non-observance of the safet
instructions can lead to an electric shock, burns and/or severe injuries.
This manual should be kept for later use and enclosed with the magnetic drilling machine, should it
be passed on or sold.
Work area
1. Keep our work area clean and well lit. Cluttered and dark work areas increase the change of
accidents;
2. Do not operate a magnetic drilling machine in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. A magnetic drilling machine ma create sparks
which could ignite the dust or fumes;
3. Keep b standers, children and visitors awa while operating a magnetic drilling machine.
Distractions can cause ou to lose control.
Electrical safety
1. A magnetic drilling machine plug must match the outlet. Never modif the plug in an wa .
Do not us an adapter plugs;
2. Avoid bod contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if our bod is grounded;
3. Do not expose the magnetic drilling machine to rain or wet conditions. Water entering a
machine will increase the risk of electric shock;
4. Do not abuse the power cable. Never use the cable to carr the magnetic drilling machine or
pull the plug from an outlet. Keep the cable awa from heat, oil, sharp edges or moving
parts. Replace damaged cables immediatel . Damaged cables increase the risk of electric
shock;
5. When operating a magnetic drilling machine, use an extension cable suitable for outdoor use,
this reduces the risk of electric shock;
6. If operating a magnetic drilling machine in a damp location is unavoidable, use a residual
current device (RCD), this reduces the risk of electric shock.

5
Personal safety
1. Sta alert, watch what ou are doing and use common sense when using a magnetic drilling
machine. Do not use the machine while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating a magnetic drilling machine ma result
in serious personal injur ;
2. Dress properl . Do not wear loose clothing or jewelr . Keep our hair, clothing and gloves
awa from moving parts. Loose clothes, jewelr or long hair can be caught in moving parts;
3. Avoid accidental starting. Be sure the switch is off before plugging the machine in. Carr ing a
magnetic drilling machine with our finger on the switch or plugging in a magnetic drilling
machine that has the switch on increases the change of accidents;
4. Never place hands, fingers, gloves or clothing near drilling area or rotating machine parts.
5. Remove adjusting ke s or switches before turning the machine on. A wrench or a ke that is
left attached to a rotating part of the machine ma result in personal injur ;
6. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the magnetic drilling machine in unexpected situations;
7. Use safet equipment. Alwa s wear e e protection. Dust mask, non-skid safet shoes, hard
hat and hearing protection must be used for optimal safet ;
8. Alwa s use supplied safet strap during an work on non-horizontal surfaces. Magnetic
drilling machine can release from surface;
When using this machine, you MUST wear ear and eye protection.
Machine use and care
1. When using the machine on non-horizontal surfaces, ou must use cutting paste. Do not use
oil because the oil can drip into the motor unit;
2. While operating the machine, the annular cutter must be cooled and lubricated with high
qualit cutting lubricants;
3. Alwa s remove the slug from the annular cutter after each hole. Caution: the slug ma be
hot;
4. Use clamps or other practical solutions to secure and support the workpiece to a stable
platform. Holding the workpiece b hand or against our bod is unstable and ma lead to
loss of control;
5. Do not use the machine when the switch does not turn it on or off. An machine that cannot
be controlled with the switch is dangerous and must be repaired;
6. Disconnect the plug from the power source before making an adjustments, changing
accessories or storing the tool. Such preventive safet measures reduce the risk of starting
the tool accidentall ;
7. Store our magnetic drilling machine out of reach for children and other untrained persons.
Tools are dangerous in the hands of untrained users;
8. Maintain our machine with care. Keep cutting tools sharp and clean. Properl maintained
tools, with sharp cutting edges are less likel to break and are easier to control;
9. Check for misalignment of moving parts, breakage of parts and an other condition that ma
affect the machine’s operation. If ou detect damage have the machine serviced before use.
Man accidents are caused b poorl maintained tools;
10. Onl use accessories that are recommended b EUROBOOR for our machine model.
Accessories that are suitable for one machine ma become hazardous when used on another
machine.

6
Service
1. Tool service must be performed onl b qualified repair personnel. Service or maintenance
performed b unqualified personnel could result in risk of injur ;
2. When servicing a tool, use onl identical replacement parts. Follow instructions in the
maintenance section of this manual. Use of unauthorised parts or failure to follow
maintenance instructions ma create a risk of electric shock or injur ;
3. EUROBOOR offers Armature kits containing official EUROBOOR spare parts suitable for our
magnetic drilling machine.
1.2 Specific safety information
•Keep our fingers awa from the drilling area;
•Avoid touching the slug that is automaticall ejected b the pilot pin when the working
procedure is finished. Contact with the slug when it is hot, or if it falls, can cause personal
injuries;
•Alwa s use the safet guard. Before switching on the machine ensure that the guard is closed
securel ;
•Alwa s use the safet strap;
•The magnetic drilling machine is suitable for use on steel with a thickness starting from 6 mm,
with zero air gap between the magnet core surface and the mounting surface. Curvature,
coats of paint and surface irregularities will create an air gap. Keep the air gap to a minimum;
•Alwa s place the machine on a flat surface;
•Do not clamp the magnetic drilling machine on small or irregular shaped objects;
•Alwa s place the machine on a surface that is clear of shavings, chips, swarf and surface dirt;
•Keep the magnet clean and free of debris and swarf;
•Do not switch on the machine before checking whether the magnetic stand has been
tightened firml to the mounting surface;
•Adjust the machine so cutter does not extend into the workpiece before drilling. Do not
perform an design, assembl or construction activities on the workpiece while the machine is
switched on;
•Before switching on the machine, make sure all accessories have been mounted correctl ;
•Do not switch on the machine until it has been mounted and installed according to all above
mentioned instructions;
•Alwa s use the recommended speed for the accessories and material ou are working with;
•Do not use the machine on the same workpiece on which electric welders are working;
•Onl use an appropriate cutting lubricant. EUROBOOR offers a wide range of well-considered
cooling and lubrication products to match our requirements;
•Do not use liquid cutting fluids while drilling verticall or overhead. Dip the cutter in cutting
paste or appl an appropriate spra for these applications;
•Do not pour cutting fluid into the reservoir while it is mounted in the bracket. Do not allow
cutting fluid to enter the drill motor;
•Before use, ensure movable safet guard operates properl ;
•In case of a jammed cutter, turn of the machine, disconnect the machine from the power
suppl and then remove the reason for the jam before turning on the machine again.

7
Residual risk
In spite of following the relevant safet regulations and their implementation, certain residual risks
cannot be avoided. These are:
•Impairment of hearing;
•Risk of personal injur from fl ing particles;
•Risk of burns due to accessories becoming hot during operation;
•Risk of personal injur due to prolonged use.
Alwa s tr to reduce these risks as much as possible.

8
2. Description
2.1 Intended use
This magnetic drilling machine is intended for commercial use as a drilling machine for drilling
materials with a magnetisable surface using annular cutters and twist drills, and for countersinking in
a weather-protected environment using the application tools and accessories recommended b
EUROBOOR.
The magnetic drilling machine can be used horizontall , verticall or overhead.
2.2 Description and features
[image 2-1]
1 Carr handle
2 Motor switch
3 Magnet switch
4 Electromagnet
5 Ring for safet strap
6 Ratchet feed handle
7 Output shaft
8 Cutter lubrication connector
9 Carbon brush LED indicator

9
2.3 Case content
1 x ECO.36+ Magnetic drilling machine
1 x safet guard
1 x ratchet feed handle
1 x hex ke 3 mm
1 x lubrication s stem
1 x safet strap
1 x bottle (200 ml) of IBO.10 cutting oil
1 x user manual
1 x safet ear protection
1 x safet goggles
1 x safet gloves
2.4 Serial number
The serial number is mentioned on the machine three times: engraved on the frame, engraved on
the magnet and on the serial no. sticker on the motor housing. Additional serial no. stickers are
provided with the machine for our administration.
The serial number will help ou, our dealer and EUROBOOR to validate and identif the machine.
For example:
0361909001
breaks down to:
036 19 09 001
Machine series
Year of manufacture
Month of manufacture
Identification number

10
2.5 Technical data
Metric
Impe
ria
l
Annular c
utting
Ø 12
-
36 mm
Ø 7/16
"
-
1 7/16
"
T
w
ist
drilling
Ø 1
-
14 mm
Ø 1/16
"
-
9/
16
"
Threa
ding
-
-
Counters
ink
ing
Ø 10
-
40 mm
Ø 3/8
"
-
1
9/16
"
In
-
corner drilling
(center to edge)
0
°
=
50
mm
0
°
=
1 31/32
"
45
°
=
6
0
mm
45
°
=
2 23/64
"
90
°
=
53
mm
90
°
=
2 3/32
"
Leng
th
310 mm
12 3/16
"
W
idth
135 mm
5 5/16
"
H
eig
ht
165 mm
6
1/2
"
S
t
r
ok
e
40 mm
1 9/16
"
W
eight
10
.
3 k
g
22.7 lbs
M
agn
et (l x w x h)
160 x 80 x 37 mm
6 5/16
"
x
3 1/8
"
x 1 7/16
"
M
a
gnetic forc
e
1
,
2
00
kg
2
,
650
lbs
M
otor power
1
,
05
0 W
9
.
5
A
T
otal power
1
,
100
W
10
A
Speed
(no load)
700 rpm
700 rpm
Speed
(load 1,050 W /
9.5
A)
400 rpm
400 rpm
S
pindle
(Weld
on
)
19
.
05 mm
3/
4"
Voltage
110
-
120
V
/ 60 Hz
220 - 240 V / 50 - 60 Hz
2. Symbols
Symbol Term, meaning Explanation
Read documentation
Be absolutel sure to read the documentation in
this user manual and specificall the “General
safet instructions” and ‘’Specific safet
in
formation
’
’
.
Wear ear protection Use ear protection during operation.
Wear e e protection Use e e protection during operation.
Danger/warning/caution Read and appl the information in the adjacent
text!
European conformit s mbol Confirms the conformit of the magnetic drilling
machine with the directives of the European
Communit .
Class of protection I
Product with basic insulation and exposed
(touchable) conductive parts additionall
connected to the protective earth conductor.

11
mm Millimeter Unit of measure for the dimensions.
" Inch Unit of measure for the dimensions.
kg Kilogram Unit of measure for the mass.
lbs Pound Unit of measure for the mass.
V Volt Unit of measure for the electric voltage.
A Ampere Unit of measure for the electric current intensit .
W Watt Unit of measure for the output.
rpm Revolutions per minute Unit of measure for the revolutions.
no No load speed Revolution speed at no load.
2.7 Environmental
Separate collection. This product must not be disposed of with normal household waste.
Separate collection of used products and packaging allows materials to be rec cled and used
again. Re-use of rec cled materials helps prevent environmental pollution and reduces the
demand for raw materials.
Local regulations ma provide for separate collection of electrical products from the household, at
municipal waste sites or at the retailer when ou purchase a new product.

12
3. Preparation & adjustment
3.1 Assembly
WARNING: To reduce the risk of injury, turn machine off and disconnect from power source
before installing and removing accessories, before adjusting or changing set ups or when
making repairs. Be sure all switches are in the OFF position. An accidental start up can cause
injury.
Fitting the feed handle
1. Take the ratchet feed handle, and line the square up with the square opening in the machine
feed axle (image 3-1);
2. Push the ratchet feed handle in the machine feed axle while pressing the release button on
the ratchet feed handle (image 3-3). You can place the feed handle in a position that best
matches our drilling set-up;
3. To change the rotation direction of the ratchet feed handle, ou can switch the small lip on
the ratchet feed handle (image 3-2):
a. To move the ratchet feed handle in clockwise direction, switch the lip to the left;
b. To move the ratchet feed handle in counter clockwise direction, switch the lip to the
right;
[image 3-1]
[image 3-2]

13
4. To release the ratchet feed handle from the machine, press the release button on the ratchet
feed handle and pull it awa from the machine;
[image 3-3]
5. It is possible to position the ratchet feed handle on either side of the machine. Method of
fitting and releasing (steps 1. to 4.) is alwa s the same.
[image 3-4]

14
Mounting the safety guard
The safet guard protects against chippings and accidental contact and must alwa s be mounted
before operation.
1. Place the drill guard in front of the machine. Make sure the long slots on the side clip over
the small humps protruding from the gearbox bod .
2. Fit the two thumbscrews in the designated holes, and tighten b hand.
Make sure the drill guard is fitted firml , but don’t overtighten the screws.
[image 3-5]
WARNING: Always use the safety guard.
Fitting the lubrication system
The lubrication s stem can onl be used for horizontal drilling (the drill being used verticall ).
1. The lubrication tank is equipped with an extra-long hose. This hose can be cut to the desired
length;
2. The tank is equipped with a magnet at the back. This makes it possible to place the tank
against an ferro product;

15
[image 3-6]

16
3. Connect the hose to the magnetic drilling machine b pushing it firml into the connector on
the machine;
[image 3-7]
4. To disconnect the hose, press the blue ring on the connector and gentl pull out the hose.
In order to use the lubrication s stem, it must be filled with a sufficient amount of cutting fluid.
1. Make sure the flow regulator is closed;
2. Unscrew the cap;
3. Fill the container with cutting fluid;
4. Screw the cap back on.
WARNING: Do not use the lubrication system in vertical or overhead drilling applications.
Instead use EUROBOOR cutting paste.

17
Fitting the safety strap
The safet strap should alwa s be used during operation. Use of the safet strap limits the risk of
personal injur when for some reason the magnet comes loose from the workpiece (such as loss of
power suppl ). In no wa does the use of the safet strap clear the operator from following other
safet and operating instructions.
The safet strap can be used in two different wa s:
1. On a narrow workpiece ou can loop the strap through the two D-rings and underneath the
workpiece . Pull the strap through its buckle and make sure the strap is tight all-around;
[image 3-8]
2. On a larger workpiece ou can loop the strap trough one D-ring and an available opening in
the workpiece itself. Pull the strap through its buckle and make sure the strap is tight all-
around.
[image 3-9]

18
WARNING: Always use the safety strap when drilling vertically and/or up side down. The
safety strap does not replace the magnetic force of the magnetic drilling machine: it is simply
used to secure against falling in the event of a magnet malfunction.
3.2 Prior to use
Please make sure that the contacting surface for the magnet is level, clean and rust free.
Remove an varnish or primer. When working on materials that are not magnetisable, suitable
fixation devices, obtainable as accessories from EUROBOOR, e. g. suction plate, vacuum plate or
pipe-drilling machine must be used.
When working on steel materials with a material thickness of less than 6 mm, the workpiece must
be reinforced with an additional steel plate in order to guarantee the magnetic holding power.
Check the machine for possible damage; Before using the machine, ou must carefull check the
protective components or slightl damaged components to ensure the are operating perfectl and
as intended.
Check that moving parts are in perfect working order, do not jam and check whether the parts are
damaged. All parts must be correctl installed and fulfill all conditions necessar to ensure perfect
operation of the machine.
Damaged protective components must be repaired or replaced according to specifications b
EUROBOOR or an authorised EUROBOOR dealer.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
DO NOT let children come into contact with the machine. Supervision is required when
inexperienced operators use this machine.
Electrical safety
The electric motor has been designed for one voltage onl . Alwa s check that the power suppl
corresponds to the voltage on the rating plate.
Your EUROBOOR magnetic drilling machine is designed in class I (grounded) according to EN 61029-1.
Earth wire is required.
If the power cable is damaged, it must be replaced b a speciall prepared cable available at
EUROBOOR or our EUROBOOR dealer.
Extension cable
If an extension cable is required, use an approved 3-core extension cable suitable for the power input
of this machine (see technical data).The minimum conductor size is 1.5 mm²; the maximum length is
30 meter. When using a cable reel, alwa s unwind the cable completel .

19
Useful tips
–Tr a few simple projects using scrap material until ou develop a ‘’feel’’ for the magnetic
drilling machine;
–Let the machine run in for a period of eight to ten hours before starting with big operations.
Do not load the machine too much during this run-in period;
–Never use the machine with serious overload;
–Keep the machine clear from moisture at all times to protect the machine, ourself and
others.

20
4. Using the machine
WARNING: Always observe the safety instructions and applicable regulations.
WARNING: To reduce the risk of serious personal injury, turn the machine off and disconnect
the machine from power source before making any adjustments or removing/installing
attachments or accessories.
4.1 Carrying handle
This machine is designed to be carried b hand onl , with the use of the integrated retractable
carr ing handle. Alwa s check if the 4 screws holding the carr ing handle in place are still firml
tightened prior to carr ing the machine.
1) To extract the carr ing handle, gentl pull it up at both ends simultaneousl (image 4-1);
2) The machine should be carried with one hand onl , with 4 fingers (all other than the thumb);
3) To retract the carr ing handle, gentl push it down. Be careful not to get an bod parts
stuck.
It is advised to have the carr ing handle retracted during operation, as it increases clearance around
the machine.
[image 4-1]