Eusso UGL2430-RTB User manual

1 of 11
4-Port Wireless 11n Router (2T2R)
UGL2430-RTB
Quick Installation Guide
Copyright EUSSO Technologies, Inc. All rights reserved.

2 of 11
1At lease one PC with IEEE802.11b/g/n WLAN client installed.
2One straight-through Category Ethernet cable, used to link WAN interface to xDSL or CM for
Internet connection.
3WLAN Broadband Router.
Check package contents:
9WLAN Broadband Router
9DC Power Adapter
9User’s manual CD-ROM
9RJ-45 Cable Line
Collect Installation Information:
WAN configuration (Contact your ISP or network administrator for these information)
DHCP Client
Static IP
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF .FFF
Default Gateway FFF . FFF . FFF . FFF
DNS Address FFF . FFF . FFF . FFF
PPPoE
User Name
Password
PPTP
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF .FFF
Server IPAddress FFF . FFF . FFF . FFF
User Name
Password
L2TP
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF .FFF
※To avoid users without access right through your WLAN Broadband
Router, suggest that use security mechanism like WEP, WPA or set
ID/password for web configuration login IP address 192.168.1.254.
Preparation.

3 of 11
Server IPAddress FFF . FFF . FFF . FFF
User Name
Password
LAN configuration
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF . FFF
WLAN configuration
SSID
Mode
Channel Number
LED Panel Description
LED Indicator State Description
1. Power LED On The WLAN Broadband Router is powered on.
Off The WLAN Broadband Router is powered off.
2. WLAN LED Flashing WLAN is active
Off WLAN is off
3. WPS LED Flashing The WPS feature is Enabled.
Off The WPS feature is Disabled.
4. WAN LED .
ACT Flashing Data is transmitting or receiving on the WAN
interface
On Port linked.
Off No link.
5. LAN LED
ACT Flashing Data is transmitting or receiving on the LAN
interface.
Power LED
WLAN LED
LAN LED
WAN LED
WPS LED

4 of 11
On Port linked.
Off No link.
Back Panel Description
Type1
WAN
LAN
Powe
r
Reset
WPS

5 of 11
Interfaces Description
Wireless Antenna The Wireless LAN Antenna in box.
PWR (Power) The power jack allows an external DC power supply
connection.
The external DC adaptor provide adaptive power requirement
to the WLAN Broadband Router.
LAN The RJ-45 sockets allow LAN connection through Category 5
cables. Support auto-sensing on 10/100M speed and half/ full
duplex; comply with IEEE 802.3/ 802.3u respectively.
WAN The RJ-45 socket allows WAN connection through a Category
2 cable. Support auto-sensing on 10/100M speed and half/ full
duplex; comply with IEEE 802.3/ 802.3u respectively.
RS (Reset) Push continually the reset button 5 ~ 10 seconds to reset the
configuration parameters to factory defaults.
WPS Push continually the reset button 5 ~ 10 seconds to enable the
WPS feature.

6 of 11
Installation.
Step One – Power On WLAN Broadband Router
Connect DC Power Adapter to WLAN Broadband Router and the wall power socket.
Notice: It will take about 50 seconds to complete the boot up sequence after powered on
the WLAN Broadband Router; Power LED will be active, and after that the
WLAN Activity LED will be flashing to show the WLAN interface is enabled
and working now.
Step Two – Configure WLAN Broadband Router
1. Connect your PC to LAN port for configuration setting. WLAN Broadband Router is delivered with
the following factory default parameters on the Ethernet LAN interfaces.
Default IPAddress: 192.168.1.254
Default IP subnet mask: 255.255.255.0
WEB login User Name: <empty>
WEB login Password: <empty>
Configure your PC with IP address
between 192.168.1.1 to 192.168.1.253
and subnet mask to be 255.255.255.0,
then open an Internet browser (i.e.
Microsoft IE6.1 SP1 or above) to
connect WLAN Broadband Router by
entering http://192.168.1.254 to URL
field.
The following example is to configure router as “Gateway” mode that use factory default value.
You may change those values if you think that is necessary.

7 of 11
2. Click “Setup Wizard” in submenu of Site contents
Click “Next>>” button to
go next.
3. Configure Operation Mode
Click “Gateway”.
Click “Next>>” button to
go next.

8 of 11
4. Configure Time Zone Setting configuration
Click “Next>>” button to
go next.
5. Configure LAN Interface Setup
IPAddress:
192.168.1.254.
Subnet Mask:
255.255.255.0.
Click “Next>>” button to
go next.
6. WAN Interface Setup
WAN Access Type: Select
WAN connection of ISP
provides.
WAN Options:
Static IP, DHCP Client,
PPPoE, PPTP, L2TP
Click “Next>>” button to
go next.

9 of 11
7. Wireless Basic Settings
Band: 2.4GHz(B+G)
Mode: AP
Network Type: disabled
SSID: MyWLAN
Channel: 11
Enable Mac Clone:
disabled
Click “Next>>” button to
go next.
8. Wireless Security Setup
Encryption: None
Options:
WEP, WPA (TKIP),
WPA2 (AES), WPA2
Mixed
Click “Finished” button to
close setup session.

10 of 11
Step Three – Connect WLAN client to WLAN Broadband Router wirelessly
On your wireless client PC:
1. Move your mouse to the
Network icon on the Task
bar and right click the
mouse button to bring up
the pop-up menu.
2. Click the View Available
Wireless Networks on the
pop-up menu.
3. Select the specific WLAN
network (SSID) from the
Available Networks list.
4. Click the Connect button
to establish the
communication link to the
wireless network
1
2
3
4

11 of 11
The wireless network diagram of WLAN Broadband Router..
Reference.
Please consult the user’s manual of WLAN Broadband Router for detailed and complete operation guide.