EverRide WASP Programming manual

TO OUR CUSTOMER:
Thank you for purchasing an EverRide Wasp Walk Behind Mower. We believe that
you have exercised excellent judgment in your selection. The Wasp has been designed to
give you many years of satisfactory service. Successful operation and long life depends
on proper maintenance and correct operating techniques.
Before you received your unit, the dealer has performed a pre-delivery inspection.
The dealer will discuss with you the features, operation and maintenance requirements.
Your dealer will always be there to help you any time you need assistance or need
equipment related to the use of your EverRide mower.
We recommend that you carefully read this entire manual before operating the unit.
This operator’s manual has been printed to provide you with safe operating techniques,
proper maintenance procedures, correct assembly, and parts identification on your
EverRideWalk Behind Mower. Keep this manual handy for future reference.
Should any assistance be needed in understanding any section of this manual,
contact your EverRide products dealer.
EverRide reserves the right to make changes or add improvements to its products without incurring
any obligation to make such changes to products manufactured previously. EverRide, or its dealers,
accept no responsibility for variations which may be evident in the actual specifications of its products
and the statements and descriptions contained in the publication.
© 2005
Auburn Consolidated
Industries, Inc.

OWNER’S WARRANTY INFORMATION
This warranty applies to the original retail purchaser of the
EverRide products only. The warranty period starts upon the
date of the original purchase reflected on the sales invoice.
As a condition to this warranty, the owner/operator shall
have read, understood and followed the operator’s manual
guidelines for operations and maintenance supplied with this
product, and that the product registration shall have been
mailed to EverRide. Any lack of good maintenance, such as
maintaining proper belt tension, tire pressures and lubrica-
tion shall be reason for rejection of a warranty claim.
In the judgment of EverRide, any original part found to be
defective in material, workmanship or performance, will be
repaired or replaced with a new part only by an EverRide Au-
thorized Servicing Dealer without charge for parts and labor
based on the following terms and conditions:
Warranty Coverage:
This warranty is limited to two years from the date of pur-
chase for parts and one year for labor for any EverRide
product used for commercial purposes, income producing
purposes or residential use. EverRide products used for
rental purposes are limited to 90 days of warranty. Engine
and battery warranties are provided separately by the manu-
facturer of those components.
Belts, cutting blades, grass collection bags and tires are
guaranteed to be free from manufacturer’s defects for the
first 90 days.
The mower deck shell will be warranted from cracking as
a result of defects in material or workmanship for the life of
the unit.
Service parts are warranted for 90 days from the date of
purchase.
What this warranty does not cover:
The expense incurred for delivering this product to the dealer
and returning it after repair. The responsibility of EverRide
and its servicing dealers is limited to making the required
repairs. Further, no breach of warranty shall be cause for
cancellation of the contract of sale.
Subsequent purchasers of the mower other than the original
purchaser. This warranty is not transferable.
Product(s) that has (have) been subject to improper mainte-
nance, neglect, misuse, accident, alteration, modified or op-
erated in any way contrary to the instructions specified in the
Operator’s Manual. Repairs made by unauthorized persons
will not be covered under warranty. Damages caused by use
of EverRide equipment other than for what it was designed.
Damages that are caused by unauthorized attachments, al-
terations or modifications will not be covered under warranty.
Any piece of equipment where the serial number has been
removed or is made illegible will not be covered under war-
ranty.
Wear or maintenance items (unless defective) including, but
not limited to: Clutch and brake linings, light bulbs, grass
bags, filters (air, fuel, oil), lubricants & coolants (unless used
during an authorized repair), spark plugs, injector nozzles.
As the manufacturer of this product, EverRide reserves the
right to change, modify or improve the design of any of its
products without assuming any obligation to modify or up-
grade any mower, previously sold or manufactured.
As stated above, all other implied warranties are limited in
duration. Any such implied warranties including merchant-
ability, fitness for a particular purpose, or otherwise, are dis-
claimed in their entirety after the expiration of the warranty
period. EverRide’s obligation to the original owner is strictly
and exclusively limited to the repair or replacement of de-
fective parts, and EverRide does not assume nor authorize
anyone to assume for them any other obligation.
EverRide assumes no responsibility for incidental, con-
sequential or other damages including, but not limited to:
Transportation of the mower to an Authorized Dealer and
returning it back, rental of truck or trailer for transportation,
expense for gasoline, injury to property, mechanic’s travel
time and mileage to perform repair(s), rental of a like prod-
uct, loss of use of the EverRide product, loss of savings or
revenue, loss or damage to personal property, and/or tele-
phone charges.
Exclusions or limitations as stated above may not be allowed
in some states. This warranty allows you specific legal rights
and you may have other rights in your state.
Warranty Registration
The warranty registration form must be completed and
signed by the authorized dealer and the original purchaser
and returned to EverRide within ten days of the date of pur-
chase. The date of purchase is considered the day the unit
is delivered.
Dealer or Distributor Warranties
The selling dealer and distributor makes no warranty of their
own and neither the dealer nor the distributor has any au-
thority to make any representation or promise on behalf of
EverRide, or to modify the terms or limitations of this war-
ranty in any way.

- 1
EverRide Wasp
Operator’s & Parts Manual
CONTENTS
SAFETY 2
INTRODUCTION 3
IDENTIFICATION 4
MODEL/SERIAL NUMBERS 4
SPECIFICATIONS 5
ASSEMBLY INSTRUCTIONS 5
FINAL CHECK/ADJUSTMENT 6
BEFORE OPERATING 7
HEIGHT ADJUSTMENT 8
LUBRICATION/MAINTENANCE 8
LUBRICATION 8
MAINTENANCE 9
SAFETY DECALS 10
WIRING SCHEMATIC 11
TORQUE CHART 12
PARTS PAGES 14
32” FRONT DECK ASSEMBLY 14
36” FRONT DECK ASSEMBLY 18
48” FRONT DECK ASSEMBLY 22
REAR DECK ASSEMBLY 26
HANDLE ASSEMBLY 28
CASTER ASSEMBLY 36
DECALS 38
CONTENTS

2 -
WARNING:
DO NOT allow children to operate the
machine. DO NOT allow any adult to operate
the machine without proper instruction.
DANGER:
Never add fuel to the tank while the engine
is running or hot. ALWAYS WAIT at least
five minutes before refueling and REFUEL
WITH THE ENGINE OFF. KEEP FUEL AWAY
FROM SPARKS OR FLAMES. WIPE AWAY
any fuel spillage BEFORE starting unit. Never
fill the fuel tank indoors. Wipe up any spilled
gasoline. Gasoline is highly flammable - NO
SMOKING.
Your mower is only as safe as the operator! Operator carelessness or error may result
in serious bodily injury. Improper maintenance of the machine may also result in injury.
Please read and follow these instructions on Safe Operation and be certain that anyone
using this mower fully understands and follows these instructions.
1. Familiarize yourself with the controls and
know how to stop this mower.
2. Inspect your work area carefully. Remove
debris from the area to be cut. Keep all
bystanders away from the mowing area.
3. Avoid contact with moving parts. Keep
hands and feet clear of the mower deck and
all moving parts.
4. Never direct the discharge of material
toward bystanders nor allow anyone near
the machine while in operation.
5. Never tamper with safety devices or guards.
If a guard or safety device is damaged or
removed, replace it before operating the
mower.
6. Handle gasoline carefully: use an approved
gasoline container; fill the fuel tank to within
1” from the neck with good quality leaded
or unleaded gasoline. Operator must wear
proper shoes and clothing, which may also
include safety glasses and ear protection.
7. Mow only during daylight hours or under
very good artificial light.
8. Do NOT mow in slippery conditions , keep a
firm grip on the handle bars, NEVER RUN.
9. The safety shield over the grass discharge
must always be bolted in place and in the
down position unless the grass catcher back
plate is completely installed.
10. Do NOT leave the operator position unless
the engine has been killed and blades have
stopped.
11. If a solid object has been hit by the blades,
stop the machine and check for damage.
Repair or replace damaged/broken part(s)
prior to restarting the engine.
12. Do NOT allow anyone to stand or walk on
the grass discharge side of the mower when
the mower is in operation.
13. Do NOT mow close to drop-offs, deep
ditches or other hazards. Mow hillsides
very carefully by mowing across the face of
slopes, not up or down. Do NOT mow on
steep slopes.
14. To avoid burns, DO NOT TOUCH the engine
or muffler immediately after operation.
IDENTIFICATION

- 3
INTRODUCTION
The information in this publication describes the operation, maintenance and servicing of the EverRide
Wasp mowers. Every effort has been made to provide correct and concise information to you, the operator,
as available at date of book publication. Your EverRide dealer is available should items in this book or
details of your machine not be understood.
This book is supplied with each machine to familiarize the operator with proper instructions needed for
operation and maintenance. Studying and adhering to these instructions will insure optimum machine
performance and longevity. A machine that is maintained properly and operated in the intended manner
will provide greater dividends than one that is neglected and/or operated in manner other than as intended.
Design and servicing of this machine has been kept as simple as possible to permit maintenance operations
to be carried out with tools normally available.
This book should be thoroughly read and understood prior to operation of this machine. Inexperienced
operators should study the contents of this publication and receive instruction from an experienced operator
when possible. Your EverRide dealer can also assist in areas concerning machine operation and provide
details concerning safe operation. It is suggested that this booklet be kept readily accessible, preferably
with the machine, for future reference if questions or concerns arise. If the original book should become
damaged, consult your Dealer in regards to acquiring a replacement.
Customers are strongly advised to use an official EverRide dealer in connection with any service problems
and adjustments that may occur. The EverRide dealer network is specially trained and equipped for all
service work and to advise customers on specific applications of the mower in local conditions.
INTRODUCTION

4 -
IDENTIFICATION
IDENTIFICATION
Model / Serial Numbers
Each EverRide Wasp mower is identified by means of
model and serial numbers. As a further identification,
the engine is also provided with identification
numbers.
To insure prompt, efficient service when ordering
parts or requesting repairs from an authorized
EverRide dealer, these numbers must be provided.
This is what the mower serial number plate looks
like.
Model Number
Serial Number
Auburn Consolidated Industries, Inc.
P.O. Box 350
Auburn, NE USA 68305-0350
The mower serial number plate is located below the
operator’s seat on the right hand side of vertical floor
panel. Information contained in this serial tag is the
model number and the serial number.
ENGINE MODEL NUMBER
ENGINE SERIAL NUMBER
The engine model number is found on a decal on the
left side of the engine block on the oil reservoir next
to the electric starter. The engine serial number is
located at the bottom of the same decal.
NOTE: Reference to left-hand and right-hand,
used throughout this manual, refers to the
position when standing behind the unit.
Engine troubleshooting, repair or adjustments
are not covered in this manual. A service manual
for the engine can be ordered from a Kawasaki
dealer.

- 5
Assembly Instructions
Fig. 1
6. Using the remaining 4 - 3/8” X 1” bolts and
the 4 – 3/8” nyloc nuts, bolt the upper handle
into position. (Remember that there are 3
– height settings for the handle for operator
comfort.) Route the wiring harness along
the handle, plugging it into the blade control
switch, using the screws to attach the
harness to the Operator Presence Control
switch. There is not a specific color for
hooking up the harness.
SPECIFICATIONS
Belt Tension Guide
Deflection Measured With 12 lbs. of Force
Belt
Engine to Deck
Transmission Belt
Right Blade Drive Belt
Wheel Drive
Inch Deflection
1/2”
1/2”
1/2”
(48”,52”, And 60” only)
1/2”
How to Adjust
Turnbuckle at Idler
Sliding Idler
Threaded Rod to Idler
Self-Adjusting
1. Remove inner parts box and handle from
crate. Remove outside frame work so that
the mower is setting on the pallet.
2. On a 36” mower, use 3 – 5/16” X 1 3/4” bolts
and 3 – 5/16” whizlocks and bolt the bumper
into place. (On the 48” there are 4 - bumper
bolts required.)The whizlocks should go to
the inside of the deck. When assembling
a 48” mower, make sure that the bumper
is flush with the deck on both ends of the
bumper.
3. Using 6 – 3/8” X 1” bolts (3 – used for each
caster) and 6 – 3/8” whizlock nuts, bolt the
casters into place. Position whizlock nuts to
the inside of the deck.
4. Using 2 – 5/16” X 1” bolts with 2 – 5/16”
flat washers and 2 – 15/16” nyloc nuts,
take the shifter lever with grip and bolt onto
the top side of the shifter bracket on the
transmission. Place the 5/16” flat washers
on the slotted hole side of the shifter bracket
under the 5/16” nut. Position the shift lever
so that it slides freely along the top side
of the shifter plate but still hits the stop for
reverse.
5. Mount the gas tank using the 2 – nylon hold
down straps, pulling tension on the buckles
until secure. Attach the quick coupler, on the
end of the fuel line, to the bottom of the tank.
(See Fig. 1)
SPECIFICATIONS/ASSEMBLY INSTRUCTIONS

6 -
Assembly Instructions
7. Using drive rods provided, turn them into
the 5/16” swivel located in the left and right
hand idler engagement bracket. Adjust the
rods so that there is approximately 1/4” to
3/8” between the rod and the bottom of the
thumb latch. Rods should be locked in place
by using 4 – hair pin cotters and by placing
a 5/16” flat washer to be inside of the drive
handle between the drive lever and hair pin
cotter. (See fig. 2)
8. With the thumb latches locked in the neutral
position, adjust the brake swivel until you feel
a slight resistance when hooking it back to
the idler assembly. Remember with thumb
locks in the neutral position, you should
be able to free wheel the machine. When
the thumb locks are rotated all the way to
the lock position, the brake should lock the
wheel. At this time, you may also hook up
the blade engagement rod, adjusting the
length of the rod so the bell crank will not
bottom out in the slot.
N
N
e
e
u
u
t
t
r
r
a
a
l
l
L
L
o
o
c
c
k
k
P
P
a
a
r
r
k
k
P
P
o
o
s
s
i
i
t
t
i
i
o
o
n
n
D
D
r
r
i
i
v
v
e
e
-
-
R
R
o
o
d
d
1
1
/
/
4
4
"
"
-
-
3
3
/
/
8
8
"
"
Fi
g
. 2
9. At this point, oil and fuel engine. Make
sure that the air pressures in the rear tires
are equal at (12 psi). Adjust the front tire
pressures to (20 psi). Your mower is now
ready for use.
Final Check / Adjustment
1. Adjust the brake control rod to obtain “free
wheeling” with the drive levers in the neutral
position and positive braking when the drive
levers are squeezed close to the handle
grips. Shorten the effective length of the
brake rod to increase braking.
2. Check air pressure in drive wheels (12 psi)
and caster wheels (20 psi). This is critical for
appropriate mower tracking.
3. Check for proper belt tension (see belt
tension guide).
Keep a 1/8” to 1/4” clearance between belt
guides and belts. Be sure the drive control
rod is properly adjusted in the thumb latch.
(See Fig 2.)
4. After a 10 hour “Break-In” period go through
steps 1 thru 3.
5. Proper adjustments must be maintained to
insure safe, trouble free, long life operation
of the mower. After completing the foregoing
instructions and recommended procedures
you are ready to put the mower into
operation.
CAUTION:
Excessive belt tension may cause damage!!
ASSEMBLY INSTRUCTIONS/FINAL CHECK/ADJUSTMENT

- 7
Before Operating
 Know your machine top to bottom.
 Make certain all safety standards and
instructions have been fully read and
understood.
 Be acquainted with all “SAFETY
INSTRUCTIONS” in this manual – to start.
1. Fill the fuel tank and open the fuel valve.
2. Shift the transmission to neutral.
3. Blades engagement lever must be in the
“Off” position or back.
4. Thumb latches need to be in the “Neutral
Lock” position.
5. Choke the engine as required and start.
6. After engine is running, push blade
engagement lever forward to engage
blades.
7. Shift the transmission to the desired gear (1
thru 4) for mowing, 5th gear is for transport
only.
8. Squeeze the control levers and push
forward on the thumb latches to unlock the
levers. Slowly release control levers to
engage the drive wheels.
9. In a normal mode the mower will travel in a
straight line. To turn; squeeze the drive lever
on the side in which you want to turn.
10. To STOP forward motion, squeeze both
drive levers, lock thumb latches and shift the
transmission to neutral.
WARNING:
FAILURE TO FOLLOW THE PREVIOUS
INSTRUCTIONS MAY RESULT
IN SEVERE BODILY INJURY OR
MECHANICAL FAILURE.
CAUTION:
Machine must be at a full “STOP” before
shifting from forward to reverse or from
reverse to forward. Failure to do so may
result in personal injury and/or damage
to the transmission.
BEFORE OPERATING
11. This unit is equipped with “Operator Presence
Controls” on the upper handle. When
the operator leaves the operator position
removing both hands from the “Operator
Presence Control” levers it will cause the
engine to shutdown.
THIS FEATURE IS FOR YOUR SAFETY!

8 -
HEIGHT ADJUSTMENT
REAR DECK MOUNT IN HIGHEST POSITION
(5) spacers on top of caster arm = 1 7/8” to 3 1/8”
(4) spacers on top of caster arm = 2 1/8” to 3 3/8”
(3) spacers on top of caster arm = 2 1/2” to 3 3/4”
(2) spacers on top of caster arm = 2 5/8” to 3 7/8”
(1) spacer on top of caster arm = 2 7/8” to 4 1/8”
All spacers under caster arm = 3 1/4” to 1 1/2”
REAR DECK MOUNT IN LOWEST POSITION
(5) spacers on top of caster arm = 1 1/2” to 2 3/4”
(4) spacers on top of caster arm = 1 3/4” to 3”
(3) spacers on top of caster arm = 2” to 3 1/4”
(2) spacers on top of caster arm = 2 3/8” to 3 3/8”
(1) spacer on top of caster arm = 2 5/8” to 3 7/8”
All spacers under caster arm = 2 7/8” to 4 1/8”
NOTE: Use 1/4” blade spacers to achieve cutting height between the above measurements.
C
C
a
a
s
s
t
t
e
e
r
r
A
A
r
r
m
m
C
C
a
a
s
s
t
t
e
e
r
r
A
A
r
r
m
m
S
S
p
p
a
a
c
c
e
e
r
r
s
s
C
C
a
a
s
s
t
t
e
e
r
r
A
A
s
s
s
s
y
y
B
B
l
l
a
a
d
d
e
e
S
S
p
p
a
a
c
c
e
e
r
r
s
s
H
H
i
i
g
g
h
h
e
e
s
s
t
t
R
R
e
e
a
a
r
r
D
D
e
e
c
c
k
k
M
M
o
o
u
u
n
n
t
t
P
P
o
o
s
s
i
i
t
t
i
i
o
o
n
n
L
L
o
o
w
w
e
e
s
s
t
t
Fig. 4
LUBRICATION
Grease Daily:
Idler Arm
Caster Wheels and Caster Pivots
Drive Wheels
Grease Every 100 Hours:
Bell Crank Pivot Bearing
LUBRICATION / MAINTENANCE
The following recommendations should be used to ensure proper and safe operation of the
mower.
HEIGHT ADJUSTMENT/LUBRICATION / MAINTENANCE

- 9
LUBRICATION / MAINTENANCE
NOTE:
The Peerless Transmission is “LIFETIME LUBRICATED”. If service is required, contact an
authorized Peerless Dealer or Repair Center.
5. Mower Blades: Check sharpness of mower blades after every 10 hours of operation.
To sharpen blades proceed as follows:
• Block the front end of the mower up or run front end up on ramps
• Remove blade by turning bolt counter clockwise.
• Sharpen blade with a hand file, electric grinder or blade sharpener. Wear gloves and eye
protection when sharpening. Grind blade at original bevel.
• Check balance of blade by positioning the blade on a nail or blade balance pedestal. Grind the
blade on the end that is heavier until both sides balance.
• Reinstall blades.
CAUTION:
DO NOT ADJUST OR CHANGE ATTACHMENTS UNLESS SPARK PLUG WIRE HAS BEEN
DISCONNECTED AND THE ENGINE HAS STOPPED.
New Blade
25 Degrees When Notch Starts
Discard Blade
Dangerous!
LUBRICATION / MAINTENANCE
MAINTENANCE
1. Engine: For complete maintenance and operating information for your engine, please refer to your
engine operating and maintenance manual provided by the engine manufacturer.
2. Belts: The drive and deck belts should be checked and adjusted after the first 10 hours of use and
then every 50 hours from that point on.
3. Tires: Correct tire pressure is essential for efficient operation of the mower.
4. Check tire air pressure periodically. Inflate tires to the pressures listed:
Drive Wheels = 12 psi
Caster Wheels = 20 psi

10 -
SAFETY DECALS
E363038
WARNING
WARNING
Shield Missing.
Shield Missing.
DO NOT Operate.
DO NOT Operate.
160169
DANGER
DANGER
TO AVOID SERIOUS INJURY FROM THROWN OBJECTS OR BLADE CONTACT
TO AVOID SERIOUS INJURY FROM THROWN OBJECTS OR BLADE CONTACT
DO NOT STAND NEAR MACHINE
DO NOT STAND NEAR MACHINE
WHEN IN OPERATION
WHEN IN OPERATION
DO NOT OPERATE MOWER WITHOUT
DO NOT OPERATE MOWER WITHOUT
GRASS DEFLECTOR OR GUARD IN PLACE
GRASS DEFLECTOR OR GUARD IN PLACE
160173
160173
160173
E363364
E363233
E363023
SAFETY DECALS

- 11
363208
363208
OPC SWITCH
OPC SWITCH
TO ENGINE KILL
TO ENGINE KILL
N/O
N/O
N/O
N/O
603060
603060
ON/OFF
ON/OFF
KEY SWITCH
KEY SWITCH
363164
363164
BLADE
BLADE
SWITCH
SWITCH
18 GA YELLOW
18 GA YELLOW
E
E
D
D
C
C
A
A
F
F
B
B
TO ENGINE GND.
TO ENGINE GND.
18 GA BLACK
18 GA BLACK
18 GA WHITE
18 GA WHITE
363207
363207
TRANS.NEUTRAL
TRANS.NEUTRAL
SWITCH
SWITCH
18 GA VIOLET
18 GA VIOLET
18 GA YELLOW
18 GA YELLOW
18 GA RED
18 GA RED
REAR VIEW OF SAFETY
REAR VIEW OF SAFETY
MODULE CONN.
MODULE CONN.
363372
363372
N/C
N/C
18 GA GREEN
18 GA GREEN
18 GA BROWN
18 GA BROWN
PART #: E363371
PART #: E363371
WIRE HARNESS FOR WKW1332; 13 HP KAWASAKI
WIRE HARNESS FOR WKW1332; 13 HP KAWASAKI
WIRE HARNESS FOR WKW1536; 15 HP KAWASAKI
WIRE HARNESS FOR WKW1536; 15 HP KAWASAKI
WIRE HARNESS FOR WKW1548; 15 HP KAWASAKI
WIRE HARNESS FOR WKW1548; 15 HP KAWASAKI
WIRING DIAGRAM

12 -
BOLT TORQUE CHART
FASTENER TORQUES
Mounting bolts and fasteners may tend to work loose during operation due to vibration or stress. A
visual check of the complete mower should be made daily. All fasteners should be checked for cor-
rect retention torque, weekly, and more often if the unit is being operated in rough areas.
All locally procured fastening hardware should be Grade 5 or equivalent. Use the following chart
for general torque specifications for Grade 5 standard fasteners. Special fastener torques for the
mower are shown separately below.
NOTE: All torque specifications apply to plated or oiled fasteners. When non-plated or dry fasteners
are used, increase specified torque values by 20%.
IMPORTANT:
Torque values SHOULD NOT be followed when fastening plastic parts!
SPECIAL FASTENER TORQUES
IMPORTANT:
DO NOT use the pulley nut to hold the shaft from turning during blade tightening, as the
pulley nut will be over torqued which could cause spindle spacer and bearing damage.
Mowing Blade Retaining Bolt - (5/8-11 x 1-1/2) ....................... 60 ft. lbs. (81 Nm)
Spindle Pulley Retaining Nut (3/4-16 HEX) ............................ 90 ft. lbs. (122 Nm)
Bolt Size ft. lb. N.m
1/4-20
5/16-18
3/8-16
7/16-14
1/2-13
9-12
15-20
25-35
40-55
70-90
7-9
10-15
20-25
30-40
50-60
M8
M10
M12
M14
M16
23-27
45-55
75-90
125-145
196-225
17-20
34-40
55-65
91-109
145-166

- 13
NOTES

14 -
32” Front Deck Assembly
39
20
39
27
28
49
3
40
2
1
41
18
63 34*
53
52
14
61
50
11
46
43
57
43
28
10
9
56
20
20
48
50
44
13
47
20
62
37
20
29 60
6
36
17
16
15
2
19
25
26
21
22
20 7
25
24
5
42
35 59
5
30
13
8
5
51 58
12

- 15
32” Front Deck Assembly
ITEM PART NO. QTY DESCRIPTION
1 E103027 3 3/8" WING NUT
2 960702 4 3/8" STD. FLAT WASHER
3 170131 1 ASSY, SHIELD 32 W/DECAL S/O
5 E363165 3 HAIRPIN COTTER
6 E363192 1 LARGE YOKE
7 E363196 1 CLEVIS PIN
8 E323002 1 BLADE DRIVE LINKAGE
9 E109014 1 SHOULDER BOLT
10 E363240 1 SHOULDER SPACER
11 E363085 1 CAM LINK
12 E363080 1 RIGHT EYEBOLT
13 964019 4 5/16" WHIZLOCK NUT
14 E363172 1 TURNBUCKLE BODY
15 E363097 1 TURNBUCKLE SPACER
16 E363082 1 LEFT EYEBOLT
17 E363174 1 EYEBOLT SPACER
18A 960155 2 5/8"-11 X 1 1/2" HEX BOLT
18B 960158 2 5/8"-11 X 2 1/4" HEX BOLT
19 960052 1 3/8" X 2 1/2" BOLT
20 964016 18 3/8" WHIZLOCK NUT
21 E363264 1 ENGAGEMENT IDLER (WF)
22 E363249 1 BELT SNUBBER
24 E108509 1 "E" RING
25 E363089 2 BRONZE BUSHING
26 E362071 1 ENGAGEMENT ARM W/BUSHING
27 E111004 1 1/4" - 28 ZERK
28 967115 14 5/16" NYLOC HEX NUT
29 E362024 1 IDLER PIVOT ASSY.
30 E323003 1 BLADE DRIVE BELT
34 E483035 2 16" BLADE
35 E363378 2 RAISED PULLEY
36 968087 1 3/8" NYLOC HEX NUT
37 E363090 2 BELT SHIELD SUPPORT
39 960062 4 3/8" X 5" HEX BOLT
40 960079 6 7/16" 1" HEX BOLT
41 960603 6 7/16" LOCK WASHER
42 960024 8 5/16" X 1 1/4" HEX BOLT

16 -
32” Front Deck Assembly
39
20
39
27
28
49
3
40
2
1
41
18
63 34*
53
52
14
61
50
11
46
43
57
43
28
10
9
56
20
20
48
50
44
13
47
20
62
37
20
29 60
6
36
17
16
15
2
19
25
26
21
22
20 7
25
24
5
42
35 59
5
30
13
8
5
51 58
12

- 17
32” Front Deck Assembly
43 960023 8 5/16" X 1" HEX BOLT
44 170120 1 ASSY, DECK 32 W/DECALS S/O
45 E109014 1 SHOULDER BOLT
46 E323029 1 SQUARE BUMPER
47 960026 3 5/16" X 1 3/4" HEX BOLT
48 960046 6 3/8" X 1" HEX BOLT
49 170122 1 ASSY, DEF. 32/36 W/DECAL S/O
50 E363350 4 SPINDLE BEARING
51 E363380 2 BLADE SPINDLE HOUSING
52 E583113 2 BEARING SPACER TUBE
53 E583112 2 SPINDLE SHAFT
56 E363379 2 SPINDLE ASSY COMPLETE
57 E363382 10 BLADE SPACER
58 170135 1 ASSY, CHANNEL 32 W/DECAL S/O
59 E322019 1 SPACER BRACKET
60 E104511 2 3/4"-16 HEX NUT
61 960606 2 3/4" LOCK WASHER
62 E105269 2 3/4" S.A.E. FLAT WASHER
63 E583108 2 5/8" DISC SPRING WASHER
* E491007 1 KIT, OPTIONAL MULCH
ITEM PART NO. QTY DESCRIPTION

18 -
20
39
27
28
49
3
40
2
1
41
18
63 34
53
52
14
61
50
11
46
43
57
43
28
10
9
56
20
20
48
20
50
44
13
47
20
38
62
37
20
29 60
6
36
17
16
15
2
19
25
26
21
22
20 7
25
24
5
42
35 59
5
30
13
8
5
51 58
12

36” Front Deck Assembly