EVOCA EvocaScoutV2 User manual

QUICK START GUIDE
What’s Included: Scout / Remote control / HDMI cable / USB-C Power
supply & cable / 2 AAA batteries (Antenna and coaxial cable not included)
What You’ll Need: Antenna and coaxial cable / Broadband Internet
access with ethernet connection or Wi-Fi
For information on setting up Scout, watch our video at Evoca.tv/setup.

STEP 1: Connect your antenna.
Find the best location to mount your antenna and connect
it to Scout using a coaxial cable.
STEP 2: Connect to Internet.
Connect Scout to your Internet modem using an ethernet
cable. If you plan to use Wi-Fi, reference the Settings
menu after you have powered up your television.
STEP 3: Connect to television.
Using a HDMI cable, connect to Scout and any HDMI
port on your television.
STEP 4: Connect to power.
Connect power supply to Scout using the USB-C cable.
Make sure that your television is set for the proper HDMI
port you selected in step 3.
STEP 5: Wait for channel scan.
Be sure to select “yes” if you are interested in viewing
local, over-the-air broadcasters like ABC, NBC, CBS
and Fox.
Note: If Scout is blinking yellow or you do not see a high-quality picture,
please try moving your antenna to a new location.
USB-C PD HDMI Ethernet Coaxial cable
Please visit evoca.tv/FAQ or reference your antenna’s instructions with issues or questions. Still have questions? Please visit Evoca.tv/SetUp or call 877-EVOCATV between 9 AM and 6 PM MST.
4
3
1
2
{Back of Scout}
FIVE EASY STEPS TO CONNECT!
HOW EVOCA WORKS
Evoca
Next Gen TV Tower
Place your antenna in a location to receive the strongest signal. It may take a few tries to get it right.
Keep in mind the following:
•Point towards our broadcast tower at Bogus Basin located at the mountains to the north of Boise.
•Higher is better.
•A window is sometimes, but not always, better.
Please visit evoca.tv/FAQ or reference your antenna’s instructions with issues or questions.
Antenna Set-Up Tips

NOTE:
Remove tab before use.
Important Product Information
FCC Compliance Information • Model: EvocaScoutV2
This device contains FCC ID: 2AWBYENI-1VA.
This device must be installed at least 20cm (~8 inches) from typical person
locations per FCC RF exposure guidelines.
Do not make any modifications to this device, doing so may void your authority
to operate it.
NOTE: This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, you are encouraged to try
to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the device and receiver.
•Connect the device into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
If using an outdoor antenna follow NEC guidelines included with the antenna for
grounding of the coaxial cable.
Responsible Party US Contact Information:
Evoca, 9605 S. Eisenman Road, Boise, Idaho 83716 • www.evoca.tv
Warranty information can be found at evoca.tv/warranty.
All other legal and safety information can be found at evoca.tv.
© 2020 Evoca. All rights reserved. Other products and companies mentioned
are the trademarks of their respective owners and not of Evoca.
REMOTE CONTROL
Power
Main Menu/Guide
Volume Control
Select/OK
Playback Control
Back
Sub-channel Tuning
NOTE: Power and volume controls only work when paired via IR to your TV.