EXACME 6184-0710 User manual

01
Thank you for choosing ExacMe Brand trampoline.
Safe use of a trampoline also requires adequate knowledge of technique,
as well as what not to do. Please read this manual thoroughly for key
points of safety.
1.Warning--------------------------------------------------------------------------------------2/3
2.Part List---------------------------------------------------------------------------------------4/5
3.Assembly-------------------------------------------------------------- 6/7/8/9/10/11/12/13
4.Exercise Learning------------------------------------------------------------------------14/15
5.Care and Maintenance Instruction-------------------------------------------------------16
6.Warranty/Return Policy---------------------------------------------------------------------17

02

03

04
Part List
Part
Letter Part Name Part
Amount Part Image
ALong Frame Rail 2
BShort Frame Rail 2
CLeft L-shaped Frame rail 2
DRight L-shaped Frame rail 2
ELeg Extension 8
FW-leg 4
GFrame Cover 1
I Bolt,washer,nut 8
J Allen Key 1
K Jumping Mat 1
HCable Tie 16

05
Part List
Part
Letter Part Name Part
Amount Part Image
LSpring 56
MSpring Puller 1
NUpper Net Pole 8
OLower Net Pole 8
PPole Foam Tube(Black) 16
QPole Cap(Black) 8
RPole Sleeve 8
V Ladder 1
SStraight Top Rod 4
W Enclosure Net 1
TLeft L-shaped Top Rod 2
URight L-shaped Top Rod 2

06
C
#C
D
#D
A
#A
B
#B
Top rail / Frame
Step 1
There are total 4 L-shaped frames and 4 straight frames.
Before assembly, put all the frames on the ground. Ensure that the sides of frames with
spring holes face up. The square holes for the net pole are inside of the frames.
There should be total 13 pcs spring hole on the wide side and 17 pcs spring hole on the long
side once the frame is fully assembled.

07
W-leg and leg extension
Step 2
Leg and Top Frametep 2
Step 3

08
Jumping mat and Springs
Step 4
1.Please firstly install 4 springs as the following picture.
2.For the rest springs,It is better at least 2 people to install from different
side with the spring puller.
Do not assemble the spring one by one which may cause deformation due to uneven force.
Notice
● When you move the trampoline, do not pull the trampoline from one side. It is better 2-3
people list the trampoline on opposite sides of frame and make sure frame legs are in a
vertical position.
●

09
Spring Cover
Step 5
Attach the pad to the frames and the triangle rings of the jumping mat with cable ties.
Enclosure SetStep 5
Step 6
Combine the upper and lower pole into a complete pole
The rectangular dent on the bottom is designed as that way, which will make the net poles more
stable and safer, and not wobble.
You just need to hand one side of the pole and then push the other end toward the ground and
hit it hard, finally the net pole will be connected tightly.
PROBLEM: Rectangular Dent on the bottom pole
1
2
1 2

10
Slip the pole to black sleeve
Enclosure NetStep 5
Step 7
Surrounding Steel Rods Assembly
1.Please find the parts below
1
Assembly all the poles to the frames
#S
#U#T #W

11
2. The START POINT is aligned with the door entrance of the net.Just identify the
entrance and start assembly here by Clockwise.
Slip a rod #S and a rod #T into the START POINT of the net webbing. Then connect as the following pictures show.
Repeat the actions until the steel rod set is completely inserted through the net top sleeve.
#S
#T
#U
#S
#T
#U
#S
#S #S
zipper
3.How to assembly?
●●

12
Check each connection and ensure all are properly screwed and locked.●●For the last 2 rods, it is better 2-3 people to do it.
Making adjusting of the top sleeves.
The net top sleeve is soft with tension. 2 people pull the top sleeves to the direction of the last
connection points from opposite directions, so that the net top sleeve is fully stretched. At the
same time,the last person holds the last two rods; bend the left-hand rod to left direction and
the right-hand rod to right direction until the rods fit together.
●1
2
Safety Net
2
PROBLEM
Cannot connect the last 2 steel rods?
1
2

13
LadderStep 5
Step 7
DISASSEMBLY
To disassemble, please follow the trampoline and enclosure net
combination assembly steps in reverse order.
Do not attempt to disassemble any trampoline fame parts before
the springs and jumping mat have been completely removed.

14

15

09
16

09
18