EXC ECOLOR EC-S5050 User manual

EC-S5050 SMD LED strip
Application Environment：
Indoor
Outdoor
Description
LED strip lights for indoor or outdoor applications,
such as under-cabinet lighting, coves,
landscapes, vehicles, and more. Choose 24V or
12V LED tape lights of any color, brightness, or
length, and install them using a range of
compatible accessories
Features
●10 m long cascading CSP bare led strip with
low voltage drop;
●Small size, thin and light, with small bending
force point;
●Large luminous Angle, up to 160°, light color
clean and soft, no yellow edge, good
consistency;
●Simple structure, low thermal resistance, long
life, high reliability;
●Application scenarios: Indoor Spaces:
background layout, interior decoration lighting,
advertising decoration, etc.
Basic Specifications
Color
RGB
Working Voltage
DC24V
Max. Power Consumption
9W/1M
Light Source
60pcs LEDs/1M
Length
5m/roll
Min shearable length
100mm
Control
DMX512
Source Life
50,000h
Light efficiency
30LM / W

Dimensions
Working Temperature
-30°C to 50°C
Storage Temperature
-40°C to 70°C
Packaging Information
Remark:
The above-mentioned packaging quantity and weight are only for the illustrated packaging method. For other
packaging methods, the packaging quantity and weight will be different. Specific to the actual product.
Packaging diagram
Installation electrical connection diagram

1. 5m CSP bare light strip, there is a pad every 100 mm of the light strip, the best position to cut the light strip is in the
middle of the pad, otherwise it will cause waste;
2. There is a 3M double-sided tape on the back of the light strip. Before use, tear off the sticker and paste it to the
installation position and compact it before use. Note that the installation position must be wiped clean, otherwise it will
affect the adhesive effect;
3. The red or brown wire of the light strip is connected to the positive pole, and the black or blue wire is connected to the
negative pole;
4. Use the 24 V supporting power supply to connect the positive and negative poles of the light strip, and then connect
the power supply to the AC 220V. Do not connect the light strip directly to the AC 220V, otherwise the light strip will be
damaged.
Installation Precautions
Clean the sundries on the installation
surface, ensure that the surface is
clean.
Measure the length of the lamp belt
to be installed, and cut the extra lamp
belt along the marking line of the
scissors. If the connecting wire
needs to be added, please weld it at
the next scissors mark at the cutting
position.
When pasting the light strip, the
release paper on the back shall be
lifted and pasted. It is strictly forbidden
to remove all release papers at one
time to avoid mutual adhesion of lamp
strips.

The place where the scissor mouth of
the lamp belt contacts the bottom of
the inner groove of the profile shall be
pasted with Mylar tape for isolation,
avoid short circuit.
The lamp strip at the corner is
installed as shown in the figure
above, please note:
Forbidden to bend into a right angle;
Forbidden to bend and stick to the
surface of profile.
After the lamp belt is installed, the
lamp belt wire is connected to the
power output end. Insulation,
short-circuit prevention and corrosion
prevention measures shall be taken at
the terminals and terminals.
Forbid to bend the LED.
Do not twist the lamp strip.
If the external cord of the product is damaged, the cord should be replaced by the manufacturer or its service agent or a
person with similar qualifications to avoid danger.
The data given in this specification is based on the standard products, the actual products may be different, please
refer to the real products.
All product drawings in this specification book are schematic diagrams, actual products may be different, please
refer to the actual type prevail.
When installing cables, the power and voltage of the power supply should match the product. It is recommended
that the load of the power supply be 80-90% of the nominal rated power, which is more conomy and security.
All product in the installation and use process, strictly prohibit violent installation operation, to protect the integrity
of the product appearance structure, do not arbitrarily cut, pull, squeeze, twist, beat with hard objest ect
non-standard operation.
Products in the process of installation and use process, strictly in accordance with the requirements of the manual
operation, due to human operation, improper use of the product damage, we are not responsible.
This product is subject to change without prior notice.