EXITEQ MC-HT571 User manual

Instruction Manual
Ceramic Hob
Model : MC-HT51
Thank you for purchasing the ceramic hob, please read this intructions
manual carefully before using and keep it cautiously for your future reference.

Product Introduction
Working Principle
1
The MC-HT51 microcomputer ceramic hob directly employs
resistance wire heating, and realizes power regulation with the microcomputer
controlling different heating time and closing time of the resistance wire.
High temperature protection
The temperature sensor mounted on the radiant electric the temperature
inside the cooker from time to time. When an excessive temperature is
detected, the cooking plate will be directly disconnected and stop power
output.
Safety
Dear customer,
Thank you for purchasing the our ceramic hob.
Our product can serve you many years to your satisfaction.
Please read this instructions manual carefully before using and installation.
Keep it in a good place after reading for future reference.
Thank you again for your purchase of our ceramic hob, and wish
you to enjoy the pleasure brought about by it.
The MC-HT51 microcomputer ceramic hob can meet dif ferent
kinds of cuisine demands because of resistance wire heating, micro-
computerized control and multi-power selection, really the optimal choice
for modern families.
The ceramic hob centers on customers and adopts personalized
design. The hob has safe and reliable performances, making your life
comfortable and enabling to fully enjoy the pleasure from life.

2
Safety
2
3
Residual heat indicators
After using the hob, waste heat remains in the heating area. The
power nixie tube shows the code “H”, warning to be away from the
heating area.
Auto shut down protection
During the hob working, it is shut off automatically when the default
timing reach by the program if without operating. If several heating
zones work simultaneously, the hob will be automatically shut off when
anyone heating area reaches it’s default timer. The default working
timer for various power levels are shown in the table below:
Installation
Selection of installation equipment
Drill holes on the table surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 50 mm space shall
be preserved around the hole.
Be sure the thickness of the table surface is at least 30mm. Please select
heat-resistant table material to avoid larger deformation caused by the heat
radiation from the hotplate.
As shown in Figure (1)
1
Power level 1 2 3 4 5 6 7 8 9
Default working
time(hour) 8 8 8 4 4 4 2 2 2
56cm
49cm

Note: The safety distance between the ceramic hob and the cupboard
above the hotplate should be at least 760mm.
Air intake
Figure (2)
mini 5 cm
mini 2 cm
3
Under any circumstances, make sure the ceramic hob is well
ventilated and the air inlet and outlet are not blocked.
Ensure the ceramic hob is in good work state. As shown in
Figure (2)
2
3Fix the hob on the table by screw four brackets on the bottom of hob
(see picture) after installation. Adjust the bracket position to suit for
different table top thickness.
w
e
r
c
s
t
e
k
c
a
r
b
e
s
a
b
e
l
o
h
w
e
r
c
s
Air exit
mini 5 mm

4
Cautions
The ceramic hob must be installed by qualified personnel
or technicians. We have professionals at your service. Please
never conduct the operation by yourself.
The ceramic hob shall not be mounted to cooling equipment,
dishwashers and rotary dryers.
The ceramic hob shall be installed such that better heat radiation
can be ensured to enhance its reliability.
The wall and induced heating zone above the table surface shall
withstand heat.
To avoid any damage, the sandwich layer and adhesive must be
resistant to heat.
A steam cleaner is not to be used.
A board is must to be installed underneath the hob.
4.
5.
1.
2.
3.
6.
7.
If the cable is damaged or to be replaced, the operation must be
carried out the by after-sale agent with dedicated tools to avoid
any accidents.If the appliance is being connected directly to the
mains an omnipolar circuit-breaker must be installed with a
minimum opening of 3mm between contacts. The installer must
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorised
technicians only.
4
Figure (3)
Power line connection
ensure that the correct electrical connection has been made and
that it complies with wiring rules.
The installer must ensure that the correct electrical connection has
been made and that it complies with wiring rules.
The socket shall be connected according to the relevant standard
eulb
wolley
-
neerg
N2 N1 L2 L1
yerg
nw
o
rb
kca
lb
220-240V
220-240V
eulb
wolley
-
nee
r
g
N L
y
erg
nwo
rb
kc
alb
220-240V
PE
PE
connect to the main power supply connect to the main power supply
220-240V 2+2N~ 220-240V
or connected to a single-pole cut-out. 30 minimum supply.
The method of connection is shown in Figure (3):

The ceramic hob appearance
Schematic diagram of the control panel
Instructions for Use
5
Preparation before using
After power on, the buzzer keep once, all the indicators light up for 1 second
then go out, indicating the ceramic hob enters into standby mode.
Put the pot in the center of the heating zone.
Power cord
ON/OFF
Glass plate
Control panel
1
2
3
Power regulating key
Timer regulating key
Treble zone
On/OffLock

6
ON/OFF
Note: 1. In standby working mode, press the“ON/OFF ” key
the hob switch off.
3. Every heating zone is independent each other.
Operation Instructions:
Timing function
Switch on the ceramic hob
Press the “On/Off” key, the hob go to stanby mode,all the indicator
shows “-”.If the ceramic plate is hot,the indicator shows “-” and “H”
alternately.
Press the “-” or “+“ to decrease or increase the power level. If the
power level returns to 0, the zone switch off.
2 . In the standy mode,if no any other action within 1
minutes,the hob switch off.
Cooking timer
Minute reminder
Select first one cooking zone by press the “-” or “+” of the
corresponding heating zone,then the cooking zone display flashing.
Then adjust timer by +/- of timer, after the timer indicator flashing 5
seconds, the timer is confirmed. You will find a red dot display at the
cooking zone indicator you selected. It reminds you this cooking zone
is with a timer setting. When cooking timer expire,relative cooking zone
will be swhitch off automatically. Cooking timer only works for one
cooking zone at the same time.
Timer can be used as a Minute reminder. Active timer by press “+”or ”-”
key, display shows "00", adjust timer by press +/- key, single touch
+/- key will increase or decrease 1 Minute, by press and hold +/- key
you can adjust time by 10 Minutes. After 5 seconds, display will stop
flashing, Minutes reminder start count down. Buzzer will bips for 30
seconds when setting time reached and the display shows "- -",
cooking process and power setted will not be affected by Minute reminder.
Treble loop function
The hob is fitted with double zone
Active the double zone
If you want to use bigger heating zone, press the “ ” when the hob
is in working mode .
Press the " " for the first time, it works in double loop working mode.
Press the " " for the second time, it works in treble loop working mode.
Press the " " for the third time, it returns to the single loop working
mode.
Note : 1.The function is available in the 3# heating zone.
2.You can change the power level from 1 to 9.
3. When the Double loop function is available, the corresponding
indicator shows “P”

Lock key
Lock function : To ensure the safety of children, the
hob is provided with the function of lock function.
Activating the lock function : When the lock is
deactivated, touch the “Lock” key to activate the
Lock function, and the timer indicator shows “Lo”,and the
indicator lamp will light up.
The rest keys disabled except the "ON/OFF" key.
Deactivating the lock function : When the hob in the
locking mode, you can deactivate the lock function
by holding the “lock” key for a while.
The power of each heating zone are shown as follow:
Heating zone 1 2 3
Power(w)
Inner
18001200
7
Timing cancellation:
If press the "+" and "-" simultaneously, the timing can be
cancelled automatically, with the timing indicator showing “--”.
double-loop three-loop
1800W
950W 2700W
Safety Reminding and Maintenance
A dedicated power protection
air swith protection air switch
must be incorporated in the
fixed wiring in accordance
with the wiring rules.
Never use the ceramic cooker
hob in high temperature
environments such as near a
gas stove or kerosene stove.
Do not put any detergents or
flammable materials in the
equipment installed under the
ceramic hob.

Never wash the induction
cooker with water directly to
avoid danger.
Keep electrical appliance out
of reach from children or
inform person. Do not let them
use the appliances without
supervision.
After being used for a long
time, the corresponding
heating zone of the ceramic
cooker hob is till hot. Never
touch the ceramic surface to
avoid burning.
If the supply cord is damaged
, it must be replaced by the
manufacturer, its service agent
or similarly qualified persons
in order to avoid a hazard.
8
Never have the ceramic
cooker hob to work without
food inside, otherwise its
operational performance may
be affected and danger may
happen.
For sealed foods such as
canned goods, please do not
heat them before opening their
covers so as to avoid any
dangers of explosion due to
heating expansion.
If the surface is cracked, swith
off the appliance to avoid the
possibility of electric shock.
Do not place rough or uneven
appliances, which may
damage the ceramic surface.
Metallic objects such as
knives, forks,spoons and lids
should not be placed on the
hotplate since they can get
hot.
DISPOSAL: Do not dispose this
product as unsorted municipal
waste. Collection of such waste
separately for special treatment
is necessary.
Clean the ceramic hob
on a regular basis to prevent
foreign matters from entering
the fan thus influencing the
normal operation.
Indoor use only.

9
Light Cleaning sponge
Accumulation
of dirt
Special cleaning
sponge for ceramic
glass
Rings and lime
crumbles
Sweetmeat,
melt aluminum
or plastics
Apply white vinegar to the
polluted zone, then wipe it
dry with soft cloth or a
special article available in
local markets
Use a scraper suitable for
ceramic glass (to protect
glass, a silicon product is
preferred) to remove
residuals
Special adhesive for
ceramic glass
Special adhesive for
ceramic glass
Cleanness and Maintenance
You can easily clean the surface of the ceramic hob if
following the methods given in the table.
Hint: please disconnect power before the cleaning.
Type of contam-
ination Method of cleaning Articles used for
cleaning
clean with damp cloth and
dry it with another cloth
clean with damp cloth and
dry it with another cloth
Children should be supervised to ensure that they do not play with the appliance.
3. A steam cleaner is not to be used.
1. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
2. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
5. The appliance is not intended to be operated by means of an external timer or
separate remote-control system.
4. After use, switch off the hob element by its control and do not rely on the pan
detector.

Special DecIaration
All the contents in this material have been subjected to careful check.
For any mistake and omission in printing or misunderstanding of the
contents,the company keeps the right of interpretation.
Addition:any technical improvement will be placed in the revised
manual without notice;for product appearance and color is according
to the actual one
10
Maintenance Service Warranty
For any failure of the product, please contact the special
maintenance department or the customer service center.
1. There is a year’s guarantee with this brand ceramic cooker
hob.
2. The period of warranty shall start from the date on which the invoice
is issued.
3. Any one of the following cases is without the warranty:
Damages caused by improper use, storage and maintenance of
the consumer.
Damages caused by unauthorized disassembly and repair in the
maintenance department not designated by the company.
Model of invoice and model of product maintained are not in
conformity or are altered.
Valid invoice can not be presented.
Damages caused by force majeure.
Using the ceramic hob for commercial purposes.