Farho NEXHO-NT Manual

NEXHO-NT – Internet Module
Fitting and Operating Instructions
NOTICE
Please read these instructions carefully and keep them for future consultation.
NEXHO range equipment must be installed by an accredited, qualified electrician
and must observe Low Voltage Regulations. The installation as a whole should
meet the provisions of aforesaid regulation. Any claim presented will be deemed
invalid if the prevailing regulations have not been met.

1
TABLE OF CONTENTS...........................................................................1
INSTRUCTIONS FOR USE......................................................................4
General information ..........................................................................4
Commissioning.................................................................................5
Positioning.......................................................................................8
How to synchronize a second device with an installation already done with
the original device? ...........................................................................8
How to reset the nexho application downloaded in my device? .............10
How to set the time? ......................................................................11
How to change the configuration passwords? ....................................11
How to deactivate the password request in NEXHO application?..........12
How to control your nexho installation from outside your house through
internet? .......................................................................................12
How to reset the internet module NEXHO-NT?...................................16
WORKING WITH HEATERS .................................................................18
How to install radiators in your automation network?..........................18
How to change the name of one heating zone?...................................19
How to change the temperature in the different rooms.......................19
How to activate the programs in the XP heaters................................20
How to deactivate the programs in your XP heaters...........................20
How to personalize or modify the programs of your XP heaters? .........21
How to install a radiator in a “repeater mode” ...................................21
WORKING WITH THERMOSTATS.........................................................24
How to install a thermostat module in the automation ........................24
How to change a name of a thermostat zone .....................................25
How to change the temperature in the different rooms? .....................25
How to activate the programs in the thermostat modules NEXHO-CL?.26
How to deactivate the programs in the thermostat modules NEXHO-CL?26
How to personalize or modify the programs of your thermostat modules
NEXHO-CL? ...................................................................................26
WORKING WITH PRESENCE DETECTORS ............................................28
How to install a presence detector in the automation network? ...........28
WORKING WITH FLOODING DETECTORS .............................................29
How to install a flooding detector in the automation network?..............29
TABLE OF CONTENTS

2
WORKING WITH FIRE DETECTORS......................................................30
How to install a fire detector in the automation network?....................30
WORKING WITH NUMERIC MODULES .................................................31
How to install a numeric module in the automation network ................31
WORKING WITH POWER CONTROL MODULES ....................................32
How to install power control modules in the automation network .........32
How to change a name of a power control module? ............................33
How to delete a power control module from the list? ..........................33
How to activate/deactivate a power control module from your application?34
How to activate the programs in a power control module? ..................34
How to deactivate the programs in a power control module?...............34
How to personalize or modify the programs of your power control
modules?.......................................................................................35
WORKING WITH LIGHT MODULES ......................................................36
How to install a light module in the automation network? ....................36
How to delete a light module from the list? .......................................37
How to change light intensity in any given zone/room from the nexho
application? ...................................................................................37
How to activate the programs in a light module?................................38
How to deactivate the programs in a light module? ............................38
How to personalize the programs of your light modules?.....................39
WORKING WITH BLIND MODULES ......................................................40
How to install a blind module in the automation network?....................40
How to delete a blind module from the list?.......................................41
How to open and close a blind? ........................................................42
How to activate the programs in a blind module? ...............................42
How to deactivate the programs in a light module? ............................42
How to personalize the programs of your blind modules? ....................43
CONFIGURE THE SECURITY MODE ......................................................44
How to modify the security password?..............................................44
How to receive security alarms in your mobile?..................................44
How to configure the actions that your system has to take when receiving
a potential security breach?.............................................................45
How to activate/deactivate your security mode against intrusions? ......46
How to activate/deactivate your security mode against intrusions from
the numeric module? ......................................................................47
How to configure the actions that your system has to take when receiving
a potential flooding alert? ................................................................47

3
How to activate/deactivate the security mode against flooding? ...........48
How to configure the actions that your system has to take when receiving
a potential fire alert? ......................................................................48
How to activate/deactivate the security mode against fires?................49
WORKING WITH SCENES ...................................................................50
What is an scene?..........................................................................50
How to create an scene?.................................................................50
How to activate one scene? .............................................................51
How to change a general or a security scene? ...................................51
How to delete a general or a security scene?.....................................52
WORKING WITH ASSOCIATIONS.........................................................53
Why associate?..............................................................................53
How can we associate? ...................................................................53
How to make work during certain hours a day, an association of light
modules?.......................................................................................54
TROUBLESHOOTING...........................................................................56
It has been impossible to connect with X of the X modules installed in X56
Impossible to connect with the internet module .................................57
TECHNICAL DETAILS..........................................................................58
Care and maintenance ....................................................................58
GUARANTEE CONDITIONS ..................................................................59

4
Thank you for purchasing FARHO'S Internet Module NEXHO- NT
It has been designed and manufactured in accordance with domestic
appliances' requirements pursuant to the following standards: UNE-EN
60950, UNE-EN 301 489, UNE-EN 61000-6 and UNE-EN 300 220.
The Internet Module NEXHO-NT enables you to control, by radio frequency
means, both FARHO heaters (XP Model) and any other device from the
NEXHO range installed in your house, by means of radio frequency. You will
be able to control your NEXHO installation from your smartphone, TABLET
or PC using our NEXHO application/software. Please consult our web page
www.nexho.com in order to see the operating systems that are supported
by the NEXHO application which are available to download from their
respective application/software shops you can find in the internet
Once the application is downloaded and configured together with the
Internet Module NEXHO-NT you will be able to surf through the different
existing menus and control, in an intuitive and user-friendly manner,
controlling everything in your system: modifying room temperatures, turning
the system on/off, changing the intensity of the lights in any given room,
programming the opening of the blinds, and all of this, without the need for
cables.
Moreover, if both your installation and mobile device have internet access
you will be able to do this through Internet and at no cost. You will also have
the option of configuring your Internet Module NEXHO-NT so you receive
ALERTS in your mobile device if any of the alarms in your house go off:
flooding, fire, smoke, intrusion, etc.
By simply following the instructions given here you will be able to enjoy all
the features and quality of life afforded by Farho products.
INSTRUCTIONS FOR USE
General information

5
The Internet Module NEXHO-NT comes with a connecting cable RJ45, one
radio frequency transmitting antenna , a feeder plug and a 230V/125V
adaptor.
In order to use the Internet Module NEXHO-NT it is necessary to have a
router with Wi-Fi connectivity and at least one controlling device such as a
smart phone, TABLET or PC with internet connection that are not included
in this package.
Synchronization with the NEXHO-NT module is a critical process for the
correct functioning of the installation. Please follow the next steps in the
same order as described in order to avoid any type of problems during the
initial installation.
Download the NEXHO application from the respective applications shop
(Android Market, Apple Store, etc.) in your device. Consult the instructions
manual in your Smartphone if you are not familiarized with the downloading
of applications from virtual shops. You can also consult in our web page if
you want to know the different compatibilities and existing versions for the
NEXHO application
Screw the radio frequency transmitting antenna into the corresponding
connector at the back of the Internet Module NEXHO-NT
Use the data cable RJ45 to connect the Internet Module NEXHO-NT to your
router.
Insert the feeder plug into the corresponding connector at the back of the
Internet Module NEXHO-NT and connect the feeder to the house mains.
Connect the Internet Module NEXHO-NT to the power and wait until only the
green light in the module is on.
Commissioning

6
Configure your Smartphone or any other device to connect to the Wi-Fi
network generated by the router that has been connected to the Internet
Module NEXHO-NT. This step is vital in this process. Do not forget to
connect yourself to the Wi-Fi network generated by the router when you are
doing the initial installation. If you don’t do this, the application wont connect
to the Internet Module.
Log on the NEXHO application. Make sure that any other device connected
to the Wi-Fi network generated by your router does not have the NEXHO
application open. If this is the case please close the NEXHO application on
this second device.
Start the synchronization with the Internet Module. Your terminal screen
will remain on waiting mode (if when turning on the application the Initial
Installation message does not appear, please
reset the application following the steps described in section “HOW TO
RESET THE NEXHO APPLICATION IN MY TERMINAL?” in this manual.
Using a small screw driver or any other alternative tool, push the “push
button switch” in the back of the Internet Module NEXHO-NT. After doing
so, a message will show in your device screen indicating the status of the
synchronization of your mobile device with the Internet Module NEXHO-NT.
When the synchronization progress bar finishes, the module NEXHO-NT will
be ready to start with the configuration of your installation with the NEXHO
product range.
It is possible that in some of the mobile devices, when starting up the
NEXHO application, it is not necessary to push the installation “push button
switch” (mainly some devices working with Android). If you observe that
when pressing the switch the application does not connect itself, wait for a
few seconds. More than likely synchronization will take place automatically.

7
Activate the PUSH notifications mode on your device. You
will then be able to receive messages that will inform you
about new actualizations of the application, apart from
allowing you to use the security alerts that the NEXHO
system has to offer. In order to activate PUSH notifications
select the configuration menu from the initial screen of
NEXHOs application in your mobile device or TABLET. In
some versions of this application this menu will appear in
as an icon with the shape of a tool at the top left part of
the screen. If this icon does not appear, press the “Menu”
button of your terminal. In the submenu select
“Configuration”. If you haven´t deactivated the password
request, this will be by default “nexho”. Push notifications
re
q
uire internet connection. Press now the “Notifications”.

The NEXHO system needs an start up installation in order
to link the application in the device with the Internet Module
NEXHO-NT. Moreover, the NEXHO application protects,
with a password all the menus related with security and
configuration
Nevertheless it is important to protect the wifi access to
your router with a password if you haven’t done it
previously. This way you will double protect the system
against external connections to your local network within
your NEXHO system or any other devices and PCS in your
house. Please check your routers instructions manual to
obtain more information about wifi password
confi
g
urations.


8
Farho´s Internet Module NEXHO-NT has been designed for domestic use
and must be always fitted inside the house.
Do not fit the device near water sources that might result in water getting
inside the device due to spraying or sprinkling.
Position your Internet Module in a favorable place to be reached by the
radio signals of all NEXHO devices that have been installed, as close as
possible, or in a central position.
The Internet Module NEXHO-NT allows you to synchronize your system with
several mobile devices, TABLETS or PCs. This way you will be able to gain
control of your NEXHO system from different devices.
In order to configure a second installation (or more) please follow the next
steps.
Synchronization with the NEXHO-NT module is a critical process for the
equipment to work correctly after the installation. Please follow the next
steps in the same order as described in order to avoid any type of problem
during the initial installation.
Download the NEXHO application from the respective applications shop
(Android Market, Apple Store, etc.) in your device as you have done in the
first installation.
Configure your Smartphone or any other device to connect to the Wi-Fi
network generated by the router that has been connected to the Internet
Module NEXHO-NT. This step is vital in this process. Do not forget to
Positioning
How to synchronize a second device with an installation
alread
y
done with the ori
g
inal device?

9
connect yourself to the Wi-Fi network generated by the router when you are
doing the initial installation. If you don’t do this, the application wont connect
to the Internet Module.
Log on your NEXHO application. Make sure that any other device connected
to the Wi-Fi network generated by your router does not have open the
NEXHO application. If this is the case please close the NEXHO application
on this second device, including the device where the first installation was
made.
Start the synchronization at the Internet Module. Your terminal screen will
stay on waiting mode. Using a small screw driver or any other alternative
tool, push the “push button switch” in the back of the Internet Module
NEXHO-NT. After doing so, a message will show in your device screen
indicating the status of the synchronization of your mobile device with the
Internet Module NEXHO-NT. When the synchronizations progress bar
finishes, the module NEXHO-NT will be ready to start with the configuration
of your installation with the NEXHO product range.
It is possible that in some of the mobile devices, when starting up the
NEXHO application, it is not necessary to press the installation “push
button switch” (mainly some devices working with Android). If you observe
that when pressing the switch the application does not connect itself, wait
for a few seconds. More than likely synchronization will take place
automatically.
As you will be able to see, the new installation does not have the names of
the zones or scenes originally configured in the first device. Even though you
can edit them manually (please check the corresponding sections of this
manual), NEXHO application will allow you to send the original names used
during the first installation to future installations.
In order to complete this process please take the following steps:
• Open both applications (the original device where the first
installation took place and the new device). Make sure both devices
are connected to the same WI-FI network generated by your
installations router (the Internet Module NEXHO-NT must be
connected to this router).