Fencee 8225 User manual

USER MANUAL
[phone]
www.fencee.eu
Electric fencing
AUTOMATIC SMART CHICKEN DOOR
Manual for models Art.Nr. 8225, 8226, 8227
VNT electronics s. r. o.
Dvorská 605, 563 01
Czech Republic

2
CONTENT
1Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2Installatio+n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3Solar panel install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4Set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 System time setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Opening mode setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Closing mode setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5Anti-pinch function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7Technical specications . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3
1. PREPARATION
CONFIRM THAT THE SPACE IS LARGE ENOUGH.
Before installing/assembling, make sure that you have enough space at the
place of the intended installation/assembly. For smooth operation of the
device, it is necessary to provide a minimum of 31 cm of space above the
upper edge of the door, left, right, and below at least 3 cm from the edge of
the device. Therefore, the required size of the opening you need to mount the
appliance is 20,3 × 4,8 × 25,4 cm.
PARTS NEEDED FOR INSTALLATION
• Two AA alkaline batteries (included in package, don't use rechargeable
batteries)
• 6 pcs Tapping screw (included in package)
• DC cable (included in Art.Nr. 8226 version - Automatic chicken coop door AC)
• Solar panel 2W, Art.Nr. 8228 (not included, optional accessories
for Art.Nr. 8227 version - Automatic chicken coop door AC + Solar)
• 5,2 V 1A USB adapter (included in package Art.Nr. 8226 Automatic chicken
coop door AC)
PARTS NEEDED FOR INSTALLATION
• Screwdriver
•Pencil
• Power drill
• Jigsaw/ keyhole hand saw
We recommend the use of safety goggles and gloves.

4
2.1.
Use a screwdriver to unscrew the two
screws that secure the battery cover.
2. INSTALLATION
2.2.
Remove the battery cover and place
two AA alkaline batteries inside
(Don't use rechargeable batteries).
Then close the battery cover and
tighten the screws.
2.3.
First time the door is turned on, the
door must be closed; opening does
not respond. Press the button to clo-
se the door, then perform the basic
cycle manually, press the button to
open the door until it reaches,
then the button to close the door .
2.4.
Position the opened door where it
will be installed and mark the sides
of the opening.

5
2.5.
Drill holes in the marked corners to
make it easier to use a jigsaw to cut
out the door from the hole.
2.6.
Use a jigsaw to saw off the opening
by connecting the hole.
2.7.
Before installing the door, please
make sure that the installation
surface of the door is flat and do not
bend the door panel.
2.8.
Put the door panel in the position to
be installed, and screw in the screws
gently.
Do not overtighten the screws or the
rails will be crushed and the door will
not move!

6
2.9.
Press to test the door
opening and closing.
2. INSTALLATION
3.1.
Fix the solar panel and the brackets
with screws.
3. 2 W SOLAR PANEL INSTALL (Art. Nr. 8228)
3.2.
Place the solar panel slanted upward
as shown, and x the solar panel
beside the door panel with four
selftapping screws.
3.3.
Plug the power cord from the solar
panel into the controller. Now you can
adjust the angle of the solar panel to
receive more sunlight, and tighten the
screws on the bracket after that.

7
Warning
Timer
Sensor
Mix
Battery level
Open and
close state
UP DOWNOK
Close state
Open state OPENING
CLOSING
3. 2 W SOLAR PANEL INSTALL (Art. Nr. 8228)
4. SET UP
DEFAULT MODE
The door automatically works on default mode if not congured differently
by the user. Default mode is sensor mode (Both open and close). ln the
default mode, the door detects the ambient brightness through the light
sensor, open when it detects daylight, and close when it is dark.

8
4.1. SYSTEM TIME SETTING (12/24 HOUR)
4.2. OPENING MODE SETTING
1. Press any key to light up the screen, and then press to enter the
settings.
2. Press to set the time convention, 12-hour or 24-hour. Then press
to save and enter the current time setting.
3. Press to set the hour when the hour flashes, press to save
and enter the minute setting.
4. Press to set the minute when the minute flash, press to save
and enter the next step.
1. The icon is displayed , and the coop door icon is fully open, as shown
below. Press to switch between the various modes, the top icons
will also change to indicate the selected mode.
2. Press to select the required mode and enter its settings.
This mode is for automatic opening of the coop door in the morning at the
time you have set, as shown on the following gure.
Press to set the hour when the hour flashes, press to conrm and
enter the minute setting.
Press to set the minute when the minutes flash, press to conrm
and proceed to the next step.

9
Current ambient
light level
Desired ligt level (light range
of the sensor : 45 - 99)
4.3. CLOSING MODE SETTING
This mode is for automatic opening of the coop door at dawn using the light
sensor, as shown below. The number on the left shows the current ambient
light level, and the flashing number on the right is the desired light level you
would like to set for opening the door. Press to adjust the flashing
value, press to conrm and enter the next step. The door will open when
the ambient light level reaches the desired light level you have set.
3. After the door opening mode is set, it will go to the next step.
1. The icon is displayed, and the coop door icon is fully close, as shown
below. Press to switch between the various modes, the top icons
will also change to indicate the selected mode.
2. Press to select the required mode and enter its settings.

10
Current ambient
light level
Desired light lever (light range
of the sensor : 00 - 44)
This mode is for the automatic closing of the coop door at the time you have
set, as shown on the following gure.
Press to set the hour when the hour flashes, press to conrm and
enter the minute setting.
Press to set the minute when the minutes flash, press to conrm
and proceed to the next step.
This mode is for the automatic closing of the coop door in the evening /at
dusk using the light sensor, as shown below. The number on the left shows
the current ambient light level, and the flashing number on the right is the
desired light level you would like to set for closing the door. Press to
adjust the flashing number to a desired light level, press to save and
enter the next step. The door will close when the ambient light level reaches
the desired light level you have set.
This mode uses a combination of both Sensor and Timer, when selecting this
mode, you will be requested to set the default time rst, and the screen will
display . Then you will be requested to set the Sensor, and the screen will
display .

11
5. ANTI-PINCH FUNCTION
When both are set, the door opener will use the Light Sensor as its primary
reference for closing. If it is not dark enough to close using the Light Sensor,
the default time you set will be used instead.
3. After the Closing mode setting, the screen displays SAVE, indicating the
end of the setting up process. After that, teh screen power down in 120
seconds later to save battery.
This function is designed to prevent your chickens from getting caught when
the door automatically closes (This function does not take effect when the
door is manually closed).
When the door is automatically closed and it nds that there is something
below blocking the door, it will automatically open to the highest point and
then close the door to try to remove the obstacle. This attempt is repeated
up to three times. If the door is not closed after three attempts, the screen
will display E2 and the light flashes slowly.
lf the "E2" appears, and the light flashes quickly, it means that something
is preventing the door from closing during the automatic closing process.
Please remove the obstacle and then press the button. Perform the basic
manual cycle, press the door open button , when it reaches, then the door
close button . The door will then begin to operate as previously set.
Low batteries affect anti-pinch function operation.
Battery-only or solar panel battery operation exhibits a different response to
the pinch function than adapter-only or battery adapter operation.
Battery operation even with a solar panel: responds reliably just above the
middle of the door opening and above, the distance from the bottom of the
opening increases with battery discharge.
Operation on adapter or adapter with batteries: responds reliably from the
middle of the door opening and above, here the response does not change
with battery discharge unless there is a power failure.
If the door gets stuck outside this reaction distance, it indicates a normal
closed state but is not physically open. Perform the basic cycle manually,
press the button to open the door and then the button to close the door
when the door is closed. if this condition repeats, the closing parameters
must be reset in chapter 4.3.

12
6. USAGE
Read all instructions.
1. Use two AA alkaline batteries to power the door.
Never use rechargeable batteries.
2. lf the door has to be stored unused for an extended period, the batteries
should be removed.
3. Before installing/assembling the door, make sure that you have enough
space at the place of the intended installation/assembly.
4. lnstalling the device indoors will affect the accuracy of the Sensor and Mix
modes.
5. Frequently lighting up the screen will increase battery drain.
6. The screen will always be on when the setting is not completed, and the
battery consumption will be high.
7. No matter what mode is set, you can open/close the door manually by
pressing .
8. During the setting up process, the battery level icon is not displayed.
You can judge whether the setting up is in progress by looking at this icon.
9. The main interface will display the system time and the mode. For example,
if the door opening setting is Timer and the closing is Mix, then the main
interface will display both the Timer and the Mix icons.
10. When the door is opening or closing, the following screen will be displayed
until it has nished (When the screen is on).
11. lf you'd like to test that the door will open and close using the light sensor,
simply choose Sensor mode for both opening and closing. Hold your hand
over the sensor for 4 minutes to simulate darkness and the door will close.
Remove your hand and the door will open 4 minutes later.
12. lf the screen does not light up when pressing any key, please check the
battery status.
13. lf the battery icon appears , it means your batteries' levels are getting
low and you will need to replace them soon.

13
14. It is recommend to install the door in a dry place away from any rain.
This will prolong the life span of the opener.
15. When there is a lot of dust on your chicken door, please clean it up in
time.
16. If "E1" is displayed and the light flashes rapidly, it means that there is
something wrong with the current time. Please set the current time again.
Additional information about the products:
• Doors with battery-only operation cannot be connected to
mains adapter or solar panel.
• The solar panel has its own built-in rechargeable
battery, which, when sufciently charged, will power
the door during several days. If the battery fails to
charge, the AA alkaline batteries will be used as a power
source.
• If the cable length is not sufcient to connect the solar
panel to the door, it can be adjusted with a conventional,
extension cable with 5,5/2,1 mm power connector.
Ensure waterproofness when connecting.

14
7. TECHNICAL SPECIFICATIONS
Automatic chicken
door
Art.Nr. 8225
Automatic chicken
door AC
Art.Nr. 8226
Automatic chicken
door AC + Solar
Art.Nr. 8227
• Automatic door
• User manual
• Batteries AA
• Screws
• Automatic door
• User manual
• 230 V adapter with
USB power cable
• Screws
• Automatic door
• User manual
• 230 V adapter with
USB power cable
• Solar panel
• Screws
Door weight 0,85 kg
Door size 34,9 × 24,1 × 4,6 cm
Power supply mode
(Power supply combination)
Door:
·2 pcs AA alkaline batteries
Door AC:
·2 pcs AA alkaline batteries
·adapter 5V DC
·2 pcs AA alkaline batteries + adapter 5V DC
Door AC + Solar panel:
· solar panel
·2 pcs AA alkaline batteries
·2 pcs AA alkaline batteries + solar panel
·adapter 5V DC
·2 pcs AA alkaline batteries + adapter 5V DC
Supply voltage 3,0 V (5,2 V for adapter, 7,0 V for solar panel)
Suppy current 0,2 - 1,5 A

15

16
VNT electronics s.r.o.
Dvorská 605, 563 01 Lanškroun
Czech Republic www.fencee.eu
Electric fencing
07022024