Fencee power DUO RF PDX10 User manual

STORED
ENERGY
OUTPUT
ENERGY
OUTPUT
VOLTAGE
OUTPUT
VOLTAGE 500 
SWITCHING
ON/OFF
fencee power DUORF PDX10 1,4 J 1 J 9000 V 5000 V
fencee power DUORF PDX20 3 J 2 J 12 000 V 6000 V
fencee power DUORF PDX30 4,5 J 3 J 11 200 V 6400 V
fencee power DUORF PDX40 5,7 J 4 J 10 000 V 5500 V
fencee power DUORF PDX50 7,5 J 5 J 11 000 V 6600 V
fencee power DUORF PDX70 10 J 7 J 10 500 V 7500 V
35 km 8 km 2 km 1,5 km
60 km 15 km 3 km 1,5 km
100 km 23 km 5 km 2 km
120 km 30 km 8 km 3 km
140 km 40 km 10 km 4 km
180 km 70 km 17 km 8 km
CEE
TEOR. MAX
fencee p o w e r DUO RF P DX 1 0
fencee p o w e r DUO RF P DX 2 0
fencee p o w e r DUO RF P DX 3 0
fencee p o w e r DUO RF P DX 4 0
fencee p o w e r DUO RF P DX 5 0
fencee p o w e r DUO RF P DX 7 0
230V ~ /12 V
Safe Animal Management | Power supply - 230 V~/ 12 V
Electric fencing
[phone]
www.fencee.eu
EN
INSRUCTION FOR USE
Smart Farm fencee
Cloud System is
protected in the EU
utility model.

2
In Lanškroun March 7th. 2019
Ing. Jan Horák
Executive Head of the Company
Phone: [phone]
[e-mail]
www.fencee.eu
DECLARATION OF CONFORMITY
ENERGIZERS FOR ELECTRIC FENCES
fencee power DUO RF PDX10, fencee power DUO RF PDX20
fencee power DUO RF PDX30, fencee power DUO RF PDX40
fencee power DUO RF PDX50, fencee power DUO RF PDX70
Test Report No.:
38 139
Manufacturer:
VNT electronics s.r.o.
Dvorská 605, 563 01 Lanškroun
Company ID-No.: 64793826
declares that the below listed products:
are in accordance with requirements of standards
and regulations relevant for given type of devices:
Products are safe under condition of their conventional use
in accordance with instructions for use. Declaration
of conformity is issued pursuant to these materials:
Issued by accredited Státní zkušebnou strojů a.s.,
Třanovského 622/11, 163 00, Praha 6.
This declaration is issued at explicit responsibility of the manufacturer.
2014/35/EU
2014/30/EU
2014/53/EU

3
Thank you for purchasing the product
of the company VNT electronics s.r.o.
The equipment conforms to safety regulations in accordance with
valid legislation as well as relevant EU (CE) regulations.
We also ask you to read these instructions for use before using the device carefully
and to keep it for possible application in the future.
Electric fence must be constructed so that persons are protected against
unintentional contact with pulses conductors under normal operating conditions.
From the point of view of legislation relate to the fences especially the standard
2014/35/EU - 2014/30/EU and
R&TTE EN300-220 a EN 61000-6-3:2007 + A1:2011
1. CONTENT
1Content ........................................................................................... 3
2Important recommendations .............................................................. 4
3Package contents ............................................................................. 4
4Function electric fence ........................................................................ 5
5Introduction ..................................................................................... 6
5.1 Remote control ............................................................................. 6
5.2 Enerizers PDX with power output higher than 5 J ................................... 7
5.3 List of main advantages ................................................................... 7
6Product description ............................................................................ 8
7Ready to use ................................................................................... 14
8Control ......................................................................................... 17
8.1 Control of energizer .................................................................... 18
8.2 Control of remote controller ......................................................... 19
9Explanation of LED indicating lights and bargraph indicator ........................ 22
10 Safety guidelines ............................................................................. 22
11 Troubleshooting .............................................................................. 26
12 Guarantee ...................................................................................... 27
13 Technical parameters ........................................................................ 28

4
2. IMPORTANT RECOMMENDATIONS
•The energizer will provide better protection for your animals and land. Local conditions and
surroundings always aect the device function and for that reason the manufacturer is not
able to guarantee full protection against damage to the enclosure fence.
•Only use the original 14 V / 1 A adapter to supply the energizer. The supply voltage must not
exceed 16 V. Controller must be used if the solar panel is used as the energizer must not be
connected directly to the solar panel.
•Switch o the energizer before carrying out any work on the electric enclosure fence.
•Read thoroughly the Safety Guidelines paragraph.
•Strictly observe all safety guidelines during installation work.
•Do not connect the device on one enclosure fence to another appliance. Damage to all co-
nnected devices and appliances may occur in the event of lightning strike.
•The device may only be repaired by the manufacturer’s qualied personnel.
•Please dispose all waste in accordance with your country’s code of practice.
•Do not let the unconnected battery cable hang freely as the short circuit and the consequent
destruction of the energizer may take place.
•The displayed output voltage tolerance is ±10%.
We recommend that this manual is read thoroughly and fully
understood before using the device and that it is retained for
future reference!
3. PACKAGE CONTENTS
•Energizer fencee power DUO RF PDX
•Basic RF antenna
•Remote controller
•CR2 battery
•Earthing cable 150 cm
•Connecting cable to the fence system 100 cm
•14 V/1 A power supply adapter for mains connection
•Battery cable 170 cm
•fencee warning sign – Warning! Electric fence!
• 2 installation self-tapping screws and rawlplugs
•User Manual

5
3
9
4
6
2
15
14
12
5
8
10
11
13
6
7
8
11
1
4. FUNCTION ELECTRIC FENCE
How the electric fence works
Electric fence system consist from the energizer and fencing marked with posts and
conductors. The energizer creates regular high-voltage impulses that generate a voltage
between the conducting material and the ground. When an animal (or a person, vegetation
or similar) creates a connection between the ground and the conducting material, the circuit
is completed.
Generated impulses are unpleasant, but not dangerous to people or animals as they only
act for a short period of time and results in the desired deterrent eect. The impulse lasts
for a matter of milliseconds. These fences serve not only to enclose an area, but also act as a
deterrent e.g. to protect against wild boars.
Benefits of electric fence systems:
• Electric fences are long-lasting, simple to put up and great value for money compared with
normal fences.
• It is easy to assembly and exible for using.
• Designed for guarding and protecting dierent animals.
• Compared to other fences, such as barbed wire, it does not cause any damage to the animals.
6High-voltage connecting cable
7Conductor
8Line connector
9Fixed post
10 Tensioner
11 Insulators
12 Flexible post
13 Warning sign
14 Gate
15 Insulator of gate
1Energizer
2ON/OFF button on energizer
3Earthing cable
4Anticorrosive earthing rod
5Lightning diverter

6
5. INTRODUCTION
Energizers power DUO RF PDX may be either powered from 230 V mains using 14 V power
supply adapter (include in the package contents) or appropriate 12 V battery.
The integrated microprocessor fully controls the operation and ensures optimal performance
taking into account the condition of the fence system and the current situation.
The fence load is continuously measured during the fence systems operation. The energizers
power output is then automatically adjusted to keep the required output voltage in the widest
possible load range. This control signicantly aids in saving energy when using quality fence
system with a low load. It also optimises energy consumption to maintain adequately high
fence system voltage, which is, for example, overgrown with grass (high load).
LED indicator lights and BARGRAF on the front of the energizer show the power supply status
and fence system voltage and also signal any potential faults on the fence.
5.1 Remote control
Energizers power DUO RF PDX may be remotely controlled using RF technology and Cloud
application; it is also essential to install FENCE WiFi GATEWAY GW100, which centrally controls
and monitors all connected devices.The PDX energizer is paired with the FENCE WiFi GATEWAY
GW100 thus the energizer may be remotely controlled using the fencee Cloud application
from mobile phone or via web interface.
The PDX remote controller can be used for energizers power DUO RF PDX.
However, the energizers power DUO RF PDX can also be paired and contro-
lled using the remote controller for energizers energy DUO RF EDX
UPTODATE
INFORMATION
Online up-to-date
information on all devices.
Control and monitor
using mobile application.
CONTROL
FROM PHONE
ALARM
SIGNALLING
Immediate warning sent
to the phone and e-mail
relating to the problem.
SAVING TIME
Using remote control means that walk around
the fence system is no longer required. All is
monitored and controlled from the phone, web
site or gateway.

7
5.3 List of main advantages
Current information about the fence
Alarm signallingTransmitter range up to 10 km
The package
power DUO PD / power DUO RF PDX
contains an AC adapte
Comfort - saves unnecessary trips to
the fence
No SIM CARD needed
Award Zlatý Klas 2019
Energizer power DUO RF PDX50
Additional functions of fencee power DUO RF PDX with remote control
5.2 Energizers PDX with power output higher than 5 J
Standard’s special requirements must be observed for energizers with power output higher
than 5 J, namely time cut-o limit when the power output is increased and thus ensuring
safety.
Products must be identied by mark.
fencee energizers have time cut-o limit of 50 seconds, which means that whilst the fence
system is under load and its resistance drops below 500 Ohm (overgrown grass, fallen branches,
etc.), the energizer will supply the maximum of 5 J for 50 s. If the fence system resistance does
not increase during this time (carrying out corrective measures), the energizer will gradually
increase the power output.
Acoustic and visual warning when the fence system is suddenly under load is another feature.
If the fence resistance drops abruptly during one pulse from over than 1000 Ohm to less than
400 Ohm (fallen branches, tangled animal or human, etc.), alarm is triggered after six pulses,
acoustic warning and red LED indicator light ashes. At the same time, the pulse period is
shortened to 3 s. The alarm is switched o after increasing the fence resistance to more than
600 Ohm or after the time limit of 10 min. Both functions are independent and separate.
Power switching
Manual switching between the high and low power output; option for reducing
demand on the battery.
Control from phone
Control and monitor using the fencee Cloud mobile application.
Combined power supply
Power supply is either from 230 V mains or standard 12 V battery, which may also be
used as the backup power supply.
LED Bargraph
Provides visual information on fence system status.

8
1Connector for connecting adapter ( 14 V /1 A)
2Connector for connecting battery (12 V )
3LED control of connecting energizer and status indication
4BARGRAPH Indicator – indication of voltage on fence system
5ON/OFF switch button
6Earthing (black)
7Connection to fence system (red)
8Antenna
3
4
5
67
1
2
8
6. PRODUCT DESCRIPTION
Meaning of displayed symbols
Earthing connection for connecting to your earthing system.
Full voltage fence system connection for connecting to your fence system.

9
REMOTE CONTROLLER
Antenna
Display
Keypad
fencee power DUO RF PDX can be used for up to 10 km (with direct visibility between the
controller and the energizer). However, the maximum range and accuracy are aected by a
number of factors – weather, terrain, vegetation, etc. In a densely
forested, or built-up terrain the range will be shorter - which is not
due to a defect of the device, but by the laws of physics and technical
possibilities (within the permitted European standards).
Ensuring maximum range and accuracy of the device:
Check if the battery in the controller is sufficiently charged.
Hold the controller as high as possible, the RF antenna must
point up and be almost perpendicular to the ground.

10
DISPLAY
Sound
alarm
Controller
battery
Signal
strength
Update
mode
Type of
device
Energizer
power
Energizer
number
Energizer
battery
Measured
unit
Measured
value

11
Sound alarm
Controller alarm sound turned ON/OFF. Can be changed in the settings.
Controller Battery
Current battery capacity in the controller.
Displays three states - FULL 100 % I HALF 50 % IEMPTY
Signal strength
Indication of the quality of connection between the controller and the energizer.
Data Update Mode
Indicates the set data update mode.
Round arrow – automatic mode with a frequency of 1 minute.
Round arrow with letter i – mode with a frequency of 1 hour.
The mode setting aects the battery life in the controller.
Energizer power
Indicates the status of the energizer – ON 100 % I ON 50 % I OFF
Energizer number
Number of the selected energizer. It is possible to assign up to 6 energizers to one
controller.
Energizer battery
Current battery capacity of the energizer.
Displays three states - FULL 100% I HALF 50% I EMPTY
Type of device
Icon indicating the type of the selected device.
When communicating with the energizer, the icon will ash.
Currently, only the G- energizer icon is used.
Measured value
The value measured by the energizer and sent to the controller.
Measured unit
Unit of the measured value. Here you can see kV - voltage of the output pulse,
or V- battery voltage of the energizer.

12
Down
arrow
Pairing
Up
arrow
Info
Settings
Controller
ON/OFF
Data
Selection
Alarm
Energizer
ON/OFF
Energizer
power
Step back
KEYPAD

13
UP Arrow / DOWN Arrow (short press)
Selection of device. Change the values in the settings mode.
Data selection (short press)
Toggles the data displayed on the controller. You can display the pulse
voltage (kV) or the energizer battery voltage (V).
Settings (long press)
Switches the controller to the settings mode where you can set the behaviour
of the controller.
Settings (short press)
Switching individual items in the settings mode.
ON/OFF controller
Turn on (short press)
Exit the current mode. Goes back from pairing mode, or from setup mode
back to the main screen.
Turn on (long press)
Turns the controller on or o.
Info (short press) – manual data update
Updates the information of the selected energizer.
Pairing (long press)
Switches the remote controller into the pairing mode.
Energizer ON/OFF (short press)
Turns the selected energizer on or o.
Energizer power (short press)
Switches energizer power (50 % or 100 %).
Alarm (short press)
A short press turns o the controller's beep.
Alarm (long press)
Long press clears the alarm notication.

14
3m
Energizer min. 20 cm
above the ground
MIN.
1m
Min. 10 metres from
next earthing point 3m
1. 2. 3.
7. READY TO USE
Choose a place suitable for installation of energizer.
• where you can achieve a good earthing.
• which is distant enough from children and animals
• where energizer is well accessible.
• where permanent water stream is avoided.
To mount energizer on wall, use attached screws, on which you can hang the energizer easily.
Assembly of energizer by using DIN rail
Energizer can be easily and practically mounted by using DIN rail and mounting bracket.
Set for assembly on DIN rail can be ordered as separate accessories.

15
ON THE GROUND - IN A PUDDLE ON THE GROUND - UPSIDE DOWN
NEGATIVE
ANGLE
NEVER EXPOSE TO
A CONTINUOUS
STREAM OF WATER!
VERTICAL ON THE
WALL IDEALLY
WITH A CANOPY
We recommend
mounting on DIN rail
80 mm (Art.Nr. 8043)
•Energizers must be installed in a dry place.
•Never put energizer on ground – in moist or wet environment.
•Fasten energizer by means of hanging screw or DIN rail with mounting
bracket in vertical position – at least 20 cm above ground.
•Never expose energizer to continuous water stream.
Earthing
Correct earthing is very important because total function of the fence system is
dependent on it!
Beat earthing rod with corrosion protection into ground completely at place with maximum
and permanent humidity. On dry pieces of land or in case of soils with lower electric
conductivity, use one or several supplementary earthing rods (with length of minimum of
1m) and place them at distance of approximately 3 metres from each other.
Exceptions are fence system powered by battery energizer or working with low output. Here
minimum length of earthing rod of 50 cm is recommended. Distance of at least 10 metres must
be between earthing rod of fence system and another earthing system, for example earthing
of a house, protective earthing of electric supply system or earthing of violation alarm.
Do not connect the energizer to already existing earthing.

16
Preview of connector wiring.
Positive polarity
14 V / 1 A Upper connector
for ADAPTER
Lower connector
for BATTERY
Connecting connectors
Models fencee POWER DUO RF PDX have two waterproof input connectors; upper one
for adapter connection and lower one for battery connection. Connectors may be wrongly
connected thus always make sure that the correct connections taken place. This design has
preference for connecting to the mains voltage with the option of connecting to the battery,
as a backup power supply in the event of power failure. Running the energizer for a long time
just from the battery is not desirable due to the higher energy consumption and low capacity
of conventional batteries.
Connecting output terminals
Connect the black earthing output to the earthing rod using earthing cable.
Connect the red output to the fence system using the connecting cable.
If the adapter and battery are connected to wrong connectors,
charging and the low battery indication will not work and the
battery will not be discharging.

17
Remote controller
• Open the device back cover.
• Insert the CR2 battery, take care about correct polarity.
• Return the cover to its original position.
• Switch on the controller by red button in the front.
The remote controller is not waterproof, keep it in a dry place.
After switching on the controller and if no energizers are paired, then different
device symbols flash alternately on the side of the display. This only means
that no energizer has been paired yet. Pairing described on page 20, chapter
8.2 Pairing.
8. CONTROL
fencee power DUO RF PDX models behave similarly to fencee DUO PD, but with several states
for radio communication operation added. Switching between states is done using the button
on the energizer. Transitions between states are indicated on the diagram below.
OFF State
The energizer is completely o. It consumes almost no energy.
It is not possible to control it remotely. No LED is active.
ON State
The energizer produces impulses and communicates with the remote controller.
Status LED is lit (adapter) or ashing (battery).
BLUE colour – 100 % output
PURPLE colour – 50 % output
RED colour – error
OFF state RF active - Standby mode
The energizer does not produce a pulse, but it can be controlled remotely.
The status LED ashes every 3 seconds.
BLUE colour – normal state
RED colour – low battery voltage
Pairing mode
Special mode designed for assigning the energizer to the remote control.
Status LED ashes BLUE very quickly.

18
8.1. Control of energizer
OUTPUT SWITCHING  ON/OFF SWITCH BUTTON
Compared to power models, the ON/OFF switch button has extended functionality here. After
rst switch-on of energizer, blue LED is burning or blinking indicating operation at higher out-
put. After each other switch-on, the generator remembers selected mode.
IN SWITCHEDOFF CONDITION OF THE ENERGIZER
Long press (> 2 s) Energizer is switched on .
Short press No response .
IN SWITCHEDON CONDITION OF THE ENERGIZER
Long press (> 2 s) manual switching between high and low output ( appro-
ximately 50 % ) – optional by user for example when using it for more sensitive ani-
mals or in case of battery saving.
Short press switching energizer off to RF active mode (Standby mode).
Short press Energizer is fully switched off.
–
Standby
mode
LONG
press
SHORT
press
SHORT
press
SHORT
press
PAIRING
mode
VERY LONG
press
LONG
press

19
SETTINGS
To enter the settings mode, press (long) the Settings button.
There are currently 3 items available in the settings menu. To select the desired item, shortly
press the Settings button.
To change the settings of the selected item, press the UP or DOWN arrow .
To exit the setting mode, shortly press the red button ON.
The settings will be saved.
Alarm sound (letter “A”)
Audio notication of the controller can be enabled or disabled. The setting is indicated by the
speaker icon.
Update mode (letter “U”)
Sets the data update interval.
Automatic mode updates the data every minute but has a higher power consumption.
Automatic mode updates the data every hour, saving battery.
Limit of the voltage of the fence
Pulse voltage limit on the fence can be set. If the voltage drops below the required limit (3 kV),
an alarm is triggered.
8.2. Control of remote controller
MAIN SCREEN
The energizer is controlled from the main screen.
Use the UP and DOWN arrows to select the desired energizer.
When the Energizer ON/OFF or Energizer Power button is pressed the controller
immediately sends the command to the energizer.
Pulse voltage, or battery voltage can be monitored on the display.
To switch battery or pulse information, press the Data Selection button.
You can update the current energizer data at any time outside
the interval by pressing the button on the controller.

20
PAIRING
To connect the energizer to the controller, it is necessary to perform “pairing“.
•Turn on the energizer, and then turn it o with one short press of the button. Then press the
button for longer time (> 5 seconds) until the status LED starts ashing fast.
Now the energizer is in pairing mode.
•Press the Pairing button on the controller for a longer time. The letter Pappears on the
display. Now the controller is in pairing mode.
•Use the UP and DOWN arrows to select the desired position number on which you
want to pair.
•Move the controller close to the energizer (up to 20 cm) and press the Pairing button.
•If everything went well, the controller is now paired with the energizer. The controller
switches back to the main screen and the energizer switches back to the OFF RF state.
•If the pairing process did not go through, perform it again.
•If you want to delete a position on the controller, perform pairing without an energizer.
•If the controller does not nd any energizer, it deletes the paired position.
•If you want to exit the pairing mode, press the red button ON.
•It is possible to pair up to 6 energizers to one controller – you can control 6 energizers with
one controller.
•It is possible to pair up to 3 controllers to one energizer – you can control one energizer with
3 controllers.