FHC PATGS02 User manual

FRAMELESS HARDWARE COMPANY P.O. Box 1906, South Gate, CA 90280 Toll Free: [phone] |Fax: [phone] |Web: fhc-usa.com
SHOWER HINGE TEMPLATE PROFESSIONAL GRADE
SEE TEMPLATE ON BACK
Refer to Dimensions Shown
to Ensure Accuracy
31"
MAX
WIDTH
SPECIFICATIONS
Glass Sizes: 1/2" (12mm) Tempered Glass Only
Construction: Solid Brass
Closing Type: Self-centering when within15 Degrees of Closed Position
Includes: Hinge body, glazing gaskets, wall mounting screws, allen
head/phillips head cover plate screws, and fabrication template.
Use: Residential Bath and Commercial Hotel Applications
PATRIOT GRANDE
Pivot Glass-to-Glass Mount for 1/2" Glass
ITEM NO. PATGS02
CARE & CLEANING GUIDELINES:
For best results, keep the following recommendations in mind when caring for your FHC shower door hardware.
Your shower door should be dried daily with a soft towel or cloth to ensure its original nish. Do not use harsh
cleaners or chemicals on the hardware, as many of the components are coated with a clear lacquer that will
become damaged beyond repair. Always test your cleaning solution in an inconspicuous area prior to cleaning
the entire hardware surface. Wipe surfaces clean using a soft, dampened cloth or sponge, and rinse completely
with warm water immediately after applying the cleaning solution. Use only small amounts of liquid, gentle,
cleaner. Never use abrasive products, sponges, or wire scrub brushes while cleaning hardware.
MAINTENANCE:
FHC’s hinges come factory greased for a silent, hassle-free experience.
If there is any noticeable squeaking that occurs after installation it is recommended
to apply a few drops of (3 in 1) multi-purpose oil to the hinge, at the nylon washer/pivot
location. The lubricant will penetrate the hinge crevices, reducing friction, cleaning
grime, and/or buildup. Spray lubricants are prohibited. If, for some reason, the
hinge is disassembled during maintenance, use a small amount of white lithium
grease to lubricate the interior hinge components.
GASKET SPECIFICATIONS:
For 1/2" Glass: Use One Thin Gasket on One Side and One Thick Gasket on the other side
For 12 mm Glass: One Thick Gasket Each Side
LIT0005E R04.05.22 PG 1 OF 2
MAXIMUM DOOR
CAPACITY
1/2" (12 mm) GLASS
WEIGHT WIDTH
USING 2 HINGES 145 LBS. (66 kg) 36" (914 mm)
NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
2-5/8"
(67 mm)
2-5/8"
(67 mm)
4-3/4"
(121 mm)
GLASS INSTRUCTIONS:
Only use tempered safety glass. To prevent damage to the hinge finish
during installation, do not use power tools when installing these hinges.
OPTIONAL PIVOT PINS:
Optional 5˚ Pivot Pin P1VPN12 are sold as a set, one pin for the top
hinge and one pin for the bottom hinge. These 5˚ offset pivot pins allow
the installer to adjust the closing position of the door 5˚ inwards or outwards.
2-HINGES
36"
MAX
WIDTH
MAX
145
LBS

FRAMELESS HARDWARE COMPANY P.O. Box 1906, South Gate, CA 90280 Toll Free: [phone] |Fax: [phone] |Web: fhc-usa.com
SHOWER HINGE TEMPLATE PROFESSIONAL GRADE
For Technical Support
Call Toll Free in the U.S.
[phone]
USE ONLY
MONOLITHIC
TEMPERED GLASS
DO NOT MEASURE / SCALE DRAWING
USE DIMENSIONS SHOWN
Cutout No. SD15
PATRIOT GRANDE
Pivot Glass-to-Glass Mount for 1/2" Glass
ITEM NO. PATGS02
IMPORTANT:
Measure from Finished
Edge of Glass
3/4" (19 mm)
Diameter
LIT0005E R04.05.22 PG 2 OF 2
1-17/32"
(39 mm)
1-17/32"
(39 mm)
1-7/8"
(48 mm)
1-7/32"
(31 mm)
1-7/32"
(31 mm)
1-7/32"
(31 mm)
1-7/32"
(31 mm)
3-1/16"
(78 mm)
2-7/16"
(62 mm)
2-7/16"
(62 mm)
3-1/16"
(78 mm)
7/8"
(22 mm)
7/8"
(22 mm)
1-7/8"
(48 mm)
1-9/16"
(40 mm)
5/16"
(8 mm)
5/16"
(8 mm)
5/16"
(8 mm)
5/16"
(8 mm)
5/16"
(8 mm)
5/16"
(8 mm)
1-9/16"
(40 mm)
1-17/32"
(39 mm)
1-17/32"
(39 mm)
EDGE PIVOT PREFERRED OPTION
EDGE OF FIXED PANELEDGE OF GLASS DOOR
5/8"
(16 mm) Diameter
5/8"
(16 mm) Diameter
1/8"
(3 mm) to
3/16" (5mm)
Clearance
FIXED TRANSOM
GLASS DOOR