FHC GLENDALE User manual

FRAMELESS HARDWARE COMPANY P.O. Box 1906, South Gate, CA 90280 Toll Free: [phone] |Fax: [phone] |Web: fhc-usa.com
SHOWER HINGE TEMPLATE PROFESSIONAL GRADE
Glass Sizes: 3/8" to 1/2" (10 mm to 12 mm) Tempered Glass Only
Construction: Solid Brass with HD Stainless Steel Back Plate
Closing Type: Self-Centering When Within 15 Degrees of Closed Position
Cutout Required: Cutout No. SD1
Includes: Hinge body, glazing gaskets, wall mounting screws, allen
head/phillips head cover plate screws, and fabrication template.
Use: Residential Bath and Commercial Hotel Applications
SPECIFICATIONS
28"
MAX
WIDTH
32"
MAX
WIDTH
2-HINGES 3-HINGES
SEE TEMPLATE ON BACK
Refer to Dimensions Shown
to Ensure Accuracy
MAX
80
LBS
MAX
120
LBS
CARE & CLEANING GUIDELINES:
For best results, keep the following recommendations in mind when caring for your FHC shower door hardware.
Your shower door should be dried daily with a soft towel or cloth to ensure its original nish. Do not use harsh
cleaners or chemicals on the hardware, as many of the components are coated with a clear lacquer that will
become damaged beyond repair. Always test your cleaning solution in an inconspicuous area prior to cleaning
the entire hardware surface. Wipe surfaces clean using a soft, dampened cloth or sponge, and rinse completely
with warm water immediately after applying the cleaning solution. Use only small amounts of liquid, gentle,
cleaner. Never use abrasive products, sponges, or wire scrub brushes while cleaning hardware.
MAINTENANCE:
FHC’s hinges come factory greased for a silent, hassle-free experience.
If there is any noticeable squeaking that occurs after installation, it is recommended
to apply a few drops of (3 in 1) multi-purpose oil to the hinge, at the nylon washer/pivot
location. The lubricant will penetrate the hinge crevices, reducing friction, cleaning
grime, and/or buildup. Spray lubricants are prohibited. If, for some reason, the hinge
is disassembled during maintenance, use a small amount of white lithium grease
to lubricate the interior hinge components.
EXPERIENCE AND INNOVATION
GASKET SPECIFICATIONS:
For 3/8" (10mm) Glass: Use One Thick Gasket On Each Side
For 1/2" (12mm) Glass: Use One Thin Gasket On Each Side
GLASS INSTRUCTIONS:
Only use tempered safety glass. To prevent damage to the hinge nish
during installation, do not use power tools when installing these hinges.
IMPORTANT INFORMATION:
The Glendale Series Hinge has a dual degree pivot pin. It comes factory set
at 90 degrees for normal door closing applications. There is also a secondary
setting on the hinge pivot pin that can be eld adjusted to allow an additional
5 degrees of closing for jobs that require a rmer positive position against a
jamb or seal.
MAXIMUM DOOR
CAPACITY
3/8" (10 mm) GLASS 1/2" (12 mm) GLASS
WEIGHT WIDTH WEIGHT WIDTH
USING 2 HINGES 80 LBS. (36 kg) 28" (711 mm) 80 LBS. (36 kg) 28" (711 mm)
USING 3 HINGES 120 LBS. (54 kg) 32" (813 mm) 120 LBS. (54 kg) 32" (813 mm)
NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
GLENDALE
Wall Mount Hinge - Full Back Plate
ITEM NO. GLENF1
GLEN037 Glendale Wall Mount Hinge - Full Back Plate
3-1/2"
(89 mm)
2-3/16"
(56 mm) 7/16"
(11 mm)
3-1/2"
(89 mm)
2"
50 mm)
SPECIFICATIONS
28"
MAX
WIDTH
32"
MAX
WIDTH
2-HINGES 3-HINGES
SEE TEMPLATE ON BACK
Refer to Dimensions Shown
to Ensure Accuracy
MAX
80
LBS
MAX
120
LBS
LIT0001AREV. 07.25.22 PG 1 OF 2
MAXIMUM DOOR
CAPACITY
3/8" (10 mm) GLASS
Approx. 5 lb/ft2
1/2" (12 mm) GLASS
Approx. 6.4 lb/ft2
DOOR WEIGHT DOOR WIDTH
USING 2 HINGES 80 LBS. (36 kg) 28" (711 mm)
USING 3 HINGES 120 LBS. (54 kg) 32" (813 mm)
NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.

FRAMELESS HARDWARE COMPANY P.O. Box 1906, South Gate, CA 90280 Toll Free: [phone] |Fax: [phone] |Web: fhc-usa.com
SHOWER HINGE TEMPLATE PROFESSIONAL GRADE
DO NOT MEASURE / SCALE DRAWING
USE DIMENSIONS SHOWN
For Technical Support
Call Toll Free in the U.S.
[phone]
USE ONLY
MONOLITHIC
TEMPERED GLASS
EXPERIENCE AND INNOVATION
LIT0001AREV. 07.25.22 PG 2 OF 2
GLENDALE
Wall Mount Hinge - Full Back Plate
ITEM NO. GLENF1
Cutout No. SD1
CUTOUT NO. SD1
1-3/4"
(44 mm)
1-1/2"
(38 mm)
2-1/4" (57 mm)
1/4"
(6 mm)
5/8" (16 mm)
Diameter
Holes
2-1/2" (63 mm)
1-1/8"
(28.5 mm)
EDGE OF GLASS
CUT OUT
1/8" (3 mm) 1/8" (3 mm)
1-1/8"
(28.5 mm)
IMPORTANT:
Measure from Finished
Edge of Glass
EDGE OF GLASS
NOTE:
Template is for standard
3/16" (5 mm) glass-to-wall
clearance.