Filtreco Drum 100 User manual

1www.filtreco.nl
It is
clear.
www.filtreco.nl
100309
User manual
Drum 100 (pump)
EN
ORDER NUMBER

3www.filtreco.nl
Introduction
Welcome to Filtreco: Filtration systems for koi ponds
Every koi lover knows the importance of good water quality. And that means having a good filtration
system for your pond. To keep your water clear, the choice is clear: Choose Filtreco. We know how much
you love your fish, and that is why we are the specialists that you can rely on. Your goal is to keep your
water clean, clear and healthy for your fish. But for clean water, you must choose the right filtration
system for your own specific situation. That's why Filtreco oers the widest selection of pond filters.
All with an unparalleled level of service, the lowest risk of malfunction and easy installation. Make no
mistake: when only the best quality will do, choose Filtreco. High-quality technology means quality of
life for your koi.
It is clear.
Introduction
This is the user manual for the Drum 100 (pump).
By purchasing this Filtreco filter, you have made an excellent choice. Please read this user manual carefully
before you start using this system. This will enable you to familiarise yourself with the system first. Any
work carried out on or with this system must always be performed in strict accordance with this user
manual.
To ensure safe, proper use, always adhere fully with the safety guidelines. Please keep this user manual
in a safe place and transfer it to the new owner in the event that the system changes ownership.
Filtreco
Nusterweg 69
NL-6136 KT Sittard
The Netherlands
CoC 14052952
VAT NL 58.28.235.B01
Filtreco is a WTH B.V. brand.
IBAN: NL39RABO0136750729
BIC: RABONL2U
[phone]
info@filtreco.nl
www.filtreco.nl

5www.filtreco.nl
Contents
Drum
filters
Introduction ............................................................................................................ 03
Contents ................................................................................................................... 05
1. What's included .................................................................................................... 06
2. Product description ............................................................................................. 06
3. Assembling the filter ........................................................................................... 06
4. Instructions for use .............................................................................................. 06
5. Safety instructions ................................................................................................ 07
5.1 Danger of electrical shock in contact with water .......................................... 07
5.2 Pacemakers .......................................................................................................... 07
5.3 Guidelines for electrical installations ............................................................... 07
5.4 Safe use ................................................................................................................. 07
6. Placement and setup .......................................................................................... 08
6.1 Connecting the control box .............................................................................. 08
6.2 Connecting the electrodes and water level meter ........................................ 08
7. First use .................................................................................................................... 09
7.1 Sequence for first use ........................................................................................ 09
7.2 Adjusting water level meter ............................................................................. 09
7.3 Flush cycle ........................................................................................................... 09
8. Control box .............................................................................................................. 1 0
9. Control panel (malfunctions) ........................................................................... 1 0
10. Cleaning and maintenance ................................................................................ 1 2
11. Troubleshooting ..................................................................................................... 1 3
12. Winterising ............................................................................................................... 1 3
13. Wear parts ................................................................................................................ 1 3
14. Technical specifications ...................................................................................... 1 3
15. Wiring and power outages ................................................................................ 1 3
16. Technical diagram ................................................................................................. 14
17. Diagram for assembly in a pond ..................................................................... 1 5

6 Drum 100 (pump)
1. What's included
• PP basin
• PP drum with brushes
• 70 micron stainless steel panel
• PP duct
• Water level meter with 3 pins
• Drum motor
• Submersible pump
• Spray tube with 8 sprayers (the first of which has a higher
flow)
• Inlet of your own choice
• 7x 110 mm outlets
• 2x 110 mm drum bypasses
• 1x 1 1/2" drain with ball valve
• Control box
• Cover with safety lock
2. Product description
The drum filter consists of a PP basin containing a PP drum
with mesh. The drum is pump-fed and installed beside the
pond. The inlets are below the water surface level, and the dirty
water is pump-fed through the floor drains or skimmers with
one or more pumps into the first filtration chamber. On the
outflow side, the water flows out of the drum through a siphon
loop. Because the dirty water flows through the drum, contami-
nants in the water cling to the interior of the drum. As a result,
less water can flow through the mesh and the water level on
the inside of the drum rises. The water level meter detects this
and initiates the flush cycle. This cycle consists of activating
the drum motor and spray pump. This causes the drum to turn
slightly more than one full rotation and the sprayers flush the
mesh clean. The flush water then flows into the sewage along
with the waste. The cycle repeats as often as necessary.
3. Assembling the filter
The housing of the filter consists of a PP basin with one
partition. The partition is fitted with a silicone sealing strip at
the flange which separates dirty water from clean. There are
also 2 holes in the partition which are covered with a cap. In
case of a breakdown in the drum control, the covers can be
removed to enable the water to bypass the drum and flow past
it without being filtered. This enables you to still use the
biological filtration segment.
The basin is fitted with a removable waste drain. The inclined
surface accelerates the water flow, causing the waste to be
carried along with it into the drain. There are also 4 brushes
installed on the inside of the drum which sweep away any algae
or other coarse particles that cling to the drain. The drum filter
is fitted with a removable spray tube made of PP, which is
equipped with flat jet nozzles. The sprayers feature a quick-
release system, making them easy to remove for cleaning. The
water level meter in the basin consists of 3 electrodes, 1 flush
level, 2 high-level safeties and 1 common electrode. The water
level for initiating the flush cycle is adjustable. Inside the basin
is a high-pressure submersible pump which supplies water to
the sprayers under high pressure during the flush cycle.
The drum motor is mounted on the outside of the drum filter.
The shaft is enclosed by a retaining ring in the installation plate.
The shaft connects to the drum via a flange with a pipe. To
remove the drum, you can simply detach this pipe-shaft
connection, after which the drum can be taken out. You do not
have to disassemble the motor to do this. The screens can be
removed by detaching the tension straps and unscrewing the
cover panel to remove it.
4. Instructions for use
The Filtreco drum filter and all parts and accessories that it
comes with may only be used as follows:
• for cleaning garden ponds
• according to the user manual and technical specifications
• only with water temperatures between +4 ˚C and +35 ˚C.
• only suitable for transporting water
• not for commercial or industrial purposes
• not suitable for salt water
• never use without running water
• never use in combination with chemicals, foods or
flammable/explosive liquids

7www.filtreco.nl
5. Safety instructions
This system may cause bodily harm or damage to property if
you do not use it properly and in accordance with all safety
guidelines, or if you attempt to use it for any purpose other
than that for which it was designed. This system must never be
operated by children or anyone under the age of 16, or by anyone
who has a physical, mental or sensory impairment or lack of
experience and knowledge, unless they are under supervision
and have been instructed on the safe usage of the system and
informed of the dangers associated with it. Children must be
made aware that this system is not a toy. Cleaning and mainte-
nance must be performed by an adult user. This must never be
performed by a child, even if they are under supervision.
5.1 Danger of electrical shock in contact with water
If your system has not been connected properly and in ac-
cordance with the safety guidelines, and a live electrical cur-
rent comes into contact with water, this can result in electrical
shock, causing serious injury and even death. Always switch o
the current on any water-bearing equipment before you come
into contact with the water.
5.2 Pacemakers
The cover has a magnetic switch. The magnetic field may
interfere with pacemakers.
5.3 Guidelines for electrical installations
The electrical installation must be carried out in accordance
with all national legislation and may only be performed by a
nationally certified electrician. A person is considered an
electrician if they have the appropriate training, knowledge,
experience and certification, and are capable of assessing and
conducting the necessary work. The job of an electrical specialist
also includes recognising any possible hazards and complying
with all applicable regional and national standards, regulations
and provisions of law.
• For your own safety, always consult a professional electrician
in case of any problems.
• This system can only be connected to a power supply that
matches its electrical specifications. All specifications for
this system can be found in this user manual.
• The system must be protected by a residual current device
with a fixed residual current of max. 30 mA.
• Use only extension cables and power dividers that are
splash-proof and whose cable diameters are the same as
the ones supplied with the system.
• Do not allow the plug connections to come into contact
with water or moisture.
• Connect the system only to a power outlet that has been
installed according to industry standards and does not
contain a dimmer.
5.4 Safe use
• Never use this system in connection with faulty electrical
cables or a defective housing.
• Never pull on the cables to adjust the placement of the
system. Ensure that the electrical cables are not pulled
tightly.
• Lay the cables through a secure duct to avoid damage and
make sure no one can trip or fall over them.
• Only open the housing of the motor or other electrical
components if this is necessary as instructed by the user
manual.
• Only perform maintenance and other tasks on the system
as described in this user manual.
• In case of any problems that you are unable to resolve,
please contact Filtreco.
• Only use original spare parts in combination with this system.
• Do not attempt to modify the technical features or
specifications of this system in any way.
• The connector cables cannot be replaced. In case of a
broken cable, the entire system or aected part must be
replaced entirely.
• When using in the open air, a roof must be placed above
the control box and a rain-proof cover must be placed
above the motor.
• Over-voltage in the mains can cause the system to
malfunction.
• Do not inhale the spray mist from the sprayer system. The
spray mist may contain harmful bacteria.
• If the cover is lifted, the flush system stops working. Once
the flush cycle has completed, allow some time before
opening the cover.

8 Drum 100 (pump)
6. Placement and setup
If you plan to install this system in a way that deviates
significantly from the recommendations in this user manual,
allow for a specialist to inspect the installation to ensure that
all technical specifications have been met.
The drum filter must always be placed in a level position. The
bottom of the filter must be completely supported. It
is recommended to place the system on a flat cement floor.
When positioning the filter, ensure that there is adequate space
on all sides so that you have room to perform maintenance. In
order for the filtration system to work properly, the filter must
always be placed above the water level.
Any greater deviation will result in an inaccurate measuring
of the water level. If the water level rises by more than 2 cm,
the water will overflow via the duct into the sewage system.
To prevent this, position the short electrode so that it is 1 cm
below the surface on the upper side of the drain. To maintain a
constant water level, you can install an automatic filling station
with overflow function for your pond.
For optimal water flow, use all 7 outlet connections. It is
recommended to use flexible rubber sleeves and joints when
connecting the water lines. These can compensate for small
dierences in dimensions and also absorb vibration.
Install slide valves or ball valves in front of and behind the filter,
so that the filter can be emptied during maintenance.
Maintain enough distance between the wall and the drain so
that you can remove the drain.
The drainage duct can be connected to a sewage connection
with a 110 mm diameter. Make sure that the duct is positioned
at an adequate incline. It is recommended to install a pipe with
a flexible rubber sleeve. These can compensate for small
differences in dimensions and also absorb vibration. They can
also be detached to remove the drainage duct.
Always use high-quality pipes with an adequate wall thickness.
Ideally, use 45 degree elbow connectors.
Lay the pipes at a downward angle so that they can be fully
emptied during the winter to protect them against frost.
Note! Electrical shock hazard. Use of this electrical system or
installation in connection with a (swimming) pond may result
in severe injury or death.
Only use this system in accordance with national and regional
regulations.
Always use suitable transport and lifting equipment when
transporting and assembling this system.
6.1 Connecting the control box
Ensure that the control box is not plugged in to the mains
power supply! Open the control box!
Hang up the box on 4 screws aligned with the grooves on the
back of the box. Space between the holes in the wall:
w = 280 mm x h= 251 mm. Remember that the length of the
cable for the electrical equipment is 3 metres. Be careful when
opening the box and remember that the screws you must loosen
to open the door should not protrude when you turn the box
open. The same goes for when you close the box.
6.2 Connecting the electrodes and water level meter
Ensure that the control box is not plugged in to the mains
power supply! Open the control box!
Turn the gland caps on the underside of the box and slide them
over the corresponding cable. Run the cable through the
cable gland into the box, leaving adequate length. Then twist
the gland caps closed again. Connect the electrodes as shown
below using a suitable screwdriver. The labels on the electrodes
match the codes on the connection inside the box.

9www.filtreco.nl
7. First use
Before using the drum filter for the first time, it is advisable to
thoroughly clean the pond manually and flush the pipelines if
possible. The reason for this is to prevent the newly started fil-
ter from immediately experiencing an interval breakdown.
Note! Electrical shock hazard.
• Always switch o the current to the system before coming
into contact with the pond water.
• Secure the system to prevent it from unintentionally being
switched on.
• Never connect the system to a power supply that is fitted
with a dimmer.
• Do not use the system in combination with a switch that
has a timer function.
• Only switch on the control box if the submersible pump
is below the water level and the electrodes are below the
surface.
7.1 Sequence for first use
• Remove the cover from the filter.
• Check all the water inlet and outlet connections.
• Check the line from the pump to the spray tube to ensure
it is hand-tight.
• Open the valves on the outflow side.
• Open one valve in the in-flow line.
• Switch on the pump.
• Ensure that the siphon loops are placed at a constant
height of 465 mm from the ground.
• Adjust the flow of the pump to point downwards in case
the water level quickly reaches the high level.
• Check all the water inlet and outlet connections again.
• Plug the connectors into the corresponding power sockets:
The plug for the spray pump goes into the power socket labelled
"spray pump".
The plug for the drum motor goes into the power socket labelled
"drum motor".
The plug for the water pump(s) goes into the power socket
labelled "pond pump".
Any additional components connect into the power socket
labelled "spare".
Please make sure that the power sockets can support a total
output of 2500 W from "pond pump" and "spare" combined!
7.2 Adjusting water level meter
The water level meter consists of 3 stainless steel electrodes:
• The "high-level" electrode (the short coated electrode)
• The "flush-cycle" electrode: the short coated electrode
• The common electrode: the long uncoated electrode
The flush-cycle electrode is set to the lowest level by default.
This means that it flushes after the water rises by about 90 mm
before the high-level electrode is activated.
If you would like for the flush cycle to take place later, you can
unscrew the cable gland and place the electrode higher.
Afterwards, tighten the cable gland again.
Note! The other two electrodes do not have an adjusting function.
7.3 Flush cycle
If the pond's water quality is such that the flush cycle lasts less
than 3 minutes, then the flow into the water inlet must be reduced
to ensure that the cycle lasts for more than 3 minutes. After the
contamination in the pond has decreased, the throttling in the
inlet line can be gradually reduced as long as you allow for the
flush cycle time mentioned above.

10 Drum 100 (pump)
8. Control box
The control box consists of a housing with:
• 5powersockets,namely:
- Pond pump 1 for pond pump 1
- Pond pump 2 for pond pump 2
- Spare for any extra pond pump or other electrical
equipment
Note! These 3 power sockets have a combined total output
of 2500 Watts!
- Spraypumpforthehigh-pressuresubmersiblepump-max.
1000 Watts
- Drum motor for the drum motor - max. 100 Watts
- Main switch to switch the power supply to the box on
and o
9. Control panel (malfunctions)
The control panel is situated behind a locking hatch. It is easy
to unlock this hatch and open it upwards. Always close the
hatch carefully after every use.
1 Start/Stop:
Makes it possible to start and/or stop the flush cycle. This
button can be used either in manual or in automatic mode.
2 Reset Error:
Resetting an error/outage. If the error is actually resolved, it is
possible for the system to work normally again. If the error is
reset but still continues to exist, the Error LED will immediately
light up again.
3 Change Mode:
By pushing this button, you can switch back and forth between
Auto(matic) and Manual mode. In Manual mode, you can start
or stop one flush cycle by pressing Start/Stop. The flush cycle
will never start automatically in Manual mode. In Auto mode,
the flush cycle is initiated if the flush level is activated (electrodes
detect contamination) based on an increased water level.
4 Change Flush Time:
By pressing the Change Flush Time button, you can change the
flush time.
5 Power LED:
The Power LED glows green when the system is connected to
power (Main Switch is on).

11www.filtreco.nl
6 Error LED:
This LED glows red whenever an error or outage occurs. This
may indicate any of the following errors:
System Error:
Error in the control box (relay, electrodes, automation,
motherboard).
- The water pumps are switched o.
- No flush cycle is possible.
• The Main Switch is switched o
• Pull all the plugs out of the box Unplug the system's power
supply cable
• Switch the F1 automat o and then on again
• Close the box and reconnect it to power
• Switch the Main Switch on again
• If the error continues, contact Filtreco
Level Error:
The water level in the filter has reached the high-water level.
More water is flowing in than out.
- The water pumps are switched o.
- No flush cycle is possible.
• Remove the cover and look for what's causing the problem.
• Check the inlet and outlet lines.
• If the outer end of the high-level electrode is above water
again:
- place the cover on the filter
- press "Reset Error"
- The mode will then switch to Manual
• Press "Start" to initiate the manual flush cycle.
- The "Flush" LED turns green
- Check to make sure the spray pump and motor are working
- If the motor is not working, check whether its plug is
connected
- If the spray pump is not working, check whether its plug
is connected
- When the flush cycle is complete, the "Flush" LED
switches o again.
- Remove the cover and check whether the water level
has reached the required operating level again
- Repeat the steps above if necessary
- If this continues to happen, you must decrease the inflow
capacity to the filter or increase the outflow capacity
from the filter.
Door Error:
The cover (contact) is not closed. The cover is not installed or
is not closed properly.
- The water pumps are switched o.
- No flush cycle is possible.
• Check whether the cover is closed properly
• Press "Reset Error" to return to the manual cycle
• The "Door" LED switches off and the "Manual" LED
switches on
• Press "Change Mode" to return to automatic mode.
If the error continues, check whether the magnet is still in place
under the holder for the cover. If so, then perform the following
steps:
• Switch o the "Main Switch"
• Disconnect the power plug from the mains
• Open the box
• Check whether the DR+ and DR- cables are properly
connected
Interval Error:
This occurs when 50 flush cycles have occurred in a row with
a pause of less than 3 minutes between each cycle. This may
occur when the water is heavily contaminated.
- The water pumps are switched o.
• Set the flush-cycle electrode to the highest level. Now, a
flush cycle will be initiated later.
• Check the outflow lines to see whether they are clogged.
• Check the sprayer heads and clean them if needed.
If this does not help, reduce the incoming flow until the most
heavy contamination is eliminated.
7 Auto Mode LED:
The LED glows then the system is in automatic mode.
8 Manual Mode LED:
The LED glows when the system is in manual mode.

12 Drum 100 (pump)
9 LEDs for the selected time interval:
Depending on how dirty the water is, you can choose between
5 dierent flush times.
The normal flush time can be used for average water
contamination. If the pond is very clean and hardly contains
any contaminants, such as in the winter time, you can switch to
the "eco" or "smart" setting. This reduces your water consump-
tion. If the water is heavily contaminated and you would like to
flush the screen more frequently, you can choose the "super"
or "turbo" setting.
You can change the selected flush times in Manual mode by
pressing "Change Flush Time".
The sprayer does not begin spraying until 1.5 seconds after the
motor starts. This ensures that only the soiled portion of the
screen is sprayed.
The Eco setting has a spray time of 5.5 seconds (quarter turn).
The Smart setting has a spray time of 8 seconds (half turn).
The Normal setting has a spray time of 11 seconds (1 turn).
The Super setting has a spray time of 22 seconds (2 turns).
The Turbo setting has a spray time of 33 seconds (3 turns).
Make sure that there is an interval of at least 3 minutes between
flush cycles, otherwise the drum will experience an interval error.
Confirm your choice by pressing "Change Mode". Your choice
is now saved. In manual mode, you can change this again if you
wish.
10 Safety Switch:
If the 'Safety Doorswitch E' is switched on, the system is supplied
with electrical current. After you use 'Safety Doorswitch E', the
system will always start in Manual mode. If you want to open
the control box, you must switch o 'Safety Doorswitch E' or
else the door cannot be opened. This is an additional safety
feature.
10. Cleaning and maintenance
Note! Electrical shock hazard! This can result is severe injury
or death.
When performing cleaning and maintenance, always take the
following measures:
• Always switch o the power supply and secure it from
being accidentally switched back on before you come into
contact with the water or perform any maintenance work
on the system.
• General cleaning - 1x each month:
- Switch o the "Main switch" and unplug the system from
the mains power supply.
- Remove any coarse waste (such as algae) on the
inside of the drain.
- Clean the brushes inside the drum.
- Clean the inside of the drum.
- Clean the door security blocks.
- Clean the water level meter electrodes.
• Cleaning the sprayer heads - 2x per month:
- Remove the sprayer head by turning it to the left to
unscrew it from the quick-release fastener.
- Remove the gasket from the holder.
- Remove the right-angle sprayer from the connector.
- Clean it.
- Install the gasket and sprayer back into the holder.
- Turn the holder onto the clamp bracket.

13www.filtreco.nl
• Complete cleaning:
- Switch o the "Main switch" and unplug the system from
the mains power supply.
- Close the inlet and outlet spouts and drain the water
through the valve until the filter is empty.
- Remove the drain and clean it thoroughly.
- Remove the drum and brushes and clean them under
running water.
- Remove the spray pump and clean it thoroughly.
- Clean the entire inside of the filter.
• Disassemble the drum as follows:
- Disassemble the spray tube by unscrewing the
connector and removing the drain from the tube clamp.
- Disassemble the drain by loosening the bolts.
Be careful not to lose the gasket and gasket rings!
- Turn the drum until the bolt from the shaft connection
is on top. Remove this bolt.
- Slide the drum slightly towards the partition until the
tube is separated from the shaft and then carefully lift
the drum at an angle upwards out of the silicone seal. Lift
the drum out of the filter basin. Carefully set the drum
down to prevent damage to the screen.
• Assemble the drum as follows:
- Carefully lower the drum into the filter and
set its flange on the shafts of the partition.
- Press the silicone seal into the flange of the drum on
all sides, using your hand.
- Slide the drum with the flange side over the shaft.
- Turn the drum around the shaft until the hole in the shaft
is positioned underneath the hole in the tube. Reinsert
the M8 x 15 bolt and screw it tightly.
11. Troubleshooting
Error codes related to the Error LED are found in chapter 9.
The following issues may occur:
• No water flow:
- Check whether the (slide) valves are open.
- Check whether the water pumps are connected.
- Check whether the inlet or outlet is clogged.
• Insucient water flow:
- Check whether the inlet or outlet is clogged.
- There are not enough inlet connections installed.
- The circulation pump does not have enough capacity.
- There is dirty water and particles in the clean water side
outside the drum: check the seal between the partition
and the flange of the drum.
• The high-pressure pump does not work:
- The plug is not plugged into the right power socket (spray
pump).
12. Winterising
To ensure proper functioning of the system, do not allow the
water temperature to decrease below +4 degrees Celsius.
Measures that you can take:
• Place a cover or lid over the drain.
• The control and motor cannot withstand freezing tempera-
tures. Be sure to place them in a location that is protected
from rain and frost.
In case water temperatures drop below +4 degrees Celsius or
there is a chance of freezing, discontinue using the system.
• Drain the system and clean it according to the instructions
• Allow the surrounding pipes to drain
• Leave the valves open
• Protect the pipes and other components from frost if
necessary.
13. Wear parts
The following parts may be subject to wear:
• Silicone drum seal Order number 100745
• Retaining ring Order number 100757
• Brush Order number 100758
• Drum screens Order number 100703
14. Technical specifications
• Operating voltage: Vac 230V
• Plug: 16 A Euro plug
• Total power output: 3680 Watts
• Cable length: 3 m
• Drum diameter: 80 cm
• Drum length: 60 cm
• Max. flow: 100 m3/h
• Weight: 95 kg
• Height above water level: completely
• Min. water level: As stated
• Max. water level: As stated
• Number of panels: 2
• Number of sprayers: 8
15. Wiring and power outages
If the control box is further away than the 3-metre cable length,
use a CE-approved splash-resistant extension cable to reach
the motor and the spray pump.
The cables for the water level meter cannot be extended using
a power cable. This may cause the system to malfunction.
Original Filtreco cables can be ordered separately. Any damage
to the control box caused by your own wiring or third-party
extension cables is not covered by warranty.
If following a power outage, the power circuit it reactivated, the
control box will revert to its previous mode (the mode which
was activated for longer than 10 seconds): automatic mode in
automatic mode and manual mode in manual mode. The
previously selected flush time will also be reactivated.

14 Drum 100 (pump)
16. Technical diagram

15www.filtreco.nl
17. Diagram for assembly in a pond
P
P

16
Filtreco
Nusterweg 69
NL-6136 KT Sittard
The Netherlands
CoC 14052952
VAT NL 58.28.235.B01
[phone]
info@filtreco.nl
www.filtreco.nl
Filtreco is a WTH B.V. brand.