Fire Mountain JH06112001 User manual

14 kW Outdoor Gas Patio Heater/
14 kW Gas-Terassenheizer
PLEASE READ AND KEEP THESE INSTRUCTIONS FOR FUTURE USE
BITTE LESEN SIE SICH DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH UND HEBEN SIE FÜR
ZUKÜNFTIGE ZWECKE GUT AUF
SAP Code: JH06112001
For further assistance, other products and more, join us at:
Website: www.firemountain.co.uk
Facebook: www.facebook.com/fire-mountain

Thank you for choosing our Fire Mountain Outdoor Gas Patio Heater. Please read this user
manual carefully and keep it for future reference. If you need any assistance, please contact
our customer service team on the details provided on the back page of this manual.
Warning
READ THE INSTRUCTIONS BEFORE USE.
This appliance must be installed in accordance with such regulations as are in force.
This appliance requires installation by a competent person.
Use only in well-ventilated areas.
This appliance should be not used inside the home or commercial use.
This appliance should be used for space heating only.
This appliance should not be used in basements or below ground level.
This appliance has no atmospheric sensing device.
This appliance requires an approved hose and regulator that are defined under the GAS
REQUIREMENTS in the manual, or check with your gas supplier.
Do not place items on or against this appliance.
Do not store chemicals, flammable materials or spray aerosols near this appliance.
Do not operate this appliance in an explosive atmosphere, such as areas where gasoline or
other flammable liquids or vapours are stored.
Turn off the gas valve immediately if smell of gas is detected.
Extinguish any open flame.
If odour continues, contact your gas supplier immediately.
The user assumes all risk in the assembly and operation of the gas heater. Failure to follow
the warnings and instructions in this manual can result in severe personal injury, death or
property damage. If user cannot read or fully understand the instruction manual, please
contact the retailer. Supplier will not be responsible for user’s negligence.
1

2
Caution: Please read the following safety guidelines before operation
This patio heater is for outdoor use only (see attached diagrammatical representations of
outdoor areas).
This outdoor heater is not intended to be installed on recreational vehicles and/or boats.
Do not use the heater inside the home.
Gas heater without atmospheric sensing device should only be used for heating buildings
used for animal rearing or for outdoor use.
The installation must conform to appropriate State regulations.
Installation and repair should be done by a qualified service person.
Improper installation, adjustment, alteration can cause personal injury or property damage.
Do not attempt to alter the unit in any manner.
Never replace or substitute the regulator with any regulator other than the factory-
suggested replacement.
Remove transit protection before use.
Do not store or use petrol or other flammable vapours or liquids in the heater unit.
Plumbing tape must be used for all threaded gas connections to prevent leakage.
The whole gas system, hose, regulator, pilot or burner should be inspected for leaks or
damage before use, and at least annually by a qualified service person.
All leak tests should be done with a soapy water solution, Never use an open flame to check
for leaks.
Do not use the heater until all connections have been leak tested.
Turn off the gas valve immediately if smell of gas is detected.
Do not transport the heater while it's operating.
Do not move the heater after it has been turned off until the temperature has cooled
down.

3
Keep the ventilation opening of the cylinder enclosure free and clear of debris.
Do not paint the radiant screen, control panel or top canopy reflector.
Control compartment, burner and circulation air passageways of the heater must be kept
clean.
Frequent cleaning may be required as necessary.
The gas cylinder should be turned off when the heater is not in use.
Check the heater immediately if any of the following occurs:
•The heater does not reach temperature.
•The burner makes popping noise during use (a slight noise is normal when the
burner is extinguished).
•Smell of gas in conjunction with extreme yellow tipping of the burner flames.
Avoid inhaling fumes emitted from the heater's first use. Smoke and odour from the
burning of oils used in manufacturing will appear. Both the smoke and odour will dissipate
after approximately 30 minutes.
The hose assembly must be located out of pathways where people may trip over it or in
area where the hose will not be subjected to accidental damage.
Avoid twisting the flexible tubes and hoses.
Any guard or other protective device removed for servicing the heater must be replaced
before operating the heater.
Adults and children should stay away from high temperature surfaces to avoid burns or
clothing ignition.
Children should be carefully supervised when they are in the area of the heater.
Clothing or other flammable materials should not be hung on the heater or placed on or
near the heater.

4
Heater Location
The heater is primarily for outdoor use only (see
attached diagrammatical representations of outdoor
areas). Do not use it for indoors or in an enclosed
area. Always ensure that adequate fresh air
ventilation is provided.
Do not use the heater for the heating of domestic
premises.
Do not use the heater in the basements or below
ground level.
Always maintain 120 cm (47") clearance from
combustible materials, or minimum 45 cm (18") top
and 60 cm (24") sides.
Heater must be placed on level firm ground.
Never operate heater in an explosive atmosphere like in areas where gasoline or other
flammable liquids or vapours are stored.
To protect heater from strong wind, anchor the base securely to the ground with screws.
Gas Requirements
Use propane, butane or LGP only.
The heater is designed for use with 10kg cylinder. Maximum size of cylinder suitable for the
appliance is 30 cm x 59 cm (H). Inner dimension of stand with supporting bars is 325cm x 60
cm (H).
The appliance requires approved gas hose in 60 cm length and a regulator.
Regulator maximum inlet pressure must not exceed 690 kPa(100 PSI) .
Regulator outlet pressure to be 28 mbar(2.8 kPa or 11" W.C.) to 50 mbar depending on
countries.
The hose and regulator assembly must conform to local standard codes.

5
The installation must conform to local codes, or in the absence of local codes, to the
standard for the storage and handling of liquid petroleum gases.
A dented, rusted or damaged gas cylinder may be hazardous and should be checked by
your gas supplier. Never use a gas cylinder with a damaged valve connection.
The gas cylinder must be arranged to provide for vapour withdrawal from the operating
cylinder.
Avoid twisting the flexible tubes and hoses.
Never connect an unregulated gas cylinder to the heater.
Disconnect the gas cylinder when the heater is not use
Leakage Test
Gas connections on the heater are leak tested at the factory prior to shipment. A complete
gas tightness check must be performed at the installation site due to possible mishandling
in shipment or excessive pressure being applied to the heater. The heater must be checked
with a full cylinder.
1. Make sure the safety control valve is in the OFF position.
2. Make a soapy water solution of one part liquid detergent and one part water. The soapy
water solution can be applied with a spray bottle, brush or rag to all gas connections. Soap
bubbles will appear in case of a leak.
3. Turn the gas supply ON.
4. In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas
supply ON and recheck. Contact your dealer or gas supplier for assistance if bubbles
continue to appear.

Diagrammatical Representations of Outdoor Areas
6

7

Parts and Specifications
8

B. Specifications
•For outdoor use only
•Uses propane, butane or LPG only
•Max Wattage: 13.5W
•Consumption: 982g/hr
•Weight: Metal w/powder coating 14.5kg, Stainless Steel 14kg
•Height: 1860 mm
•CE approved
Tools Needed
•Open ended wrench 10 & 13mm
•Adjustable opening wrench (2) 20cm (8”) long
•Slip joint pliers 23cm (9”) long
•Screwdriver w/medium blade
•Plumbing tape for joints
•Spray bottle of soap solution for leakage test
9
WARNING
This appliance requires a
regulator that is defined under
the GAS REQUIREMENTS or
check with your gas supplier.

Assembly Procedures
Step 1
Flip the tank housing (H) upside
down and attach the wheel
assembly (J) to the base of the
tank housing (H) using 2pcs M8 x
16 screws (AA) and M8 nuts (BB).
Step 2
Assemble the burner (G) on tank
(H) with screw (CC) and Nut (DD).
10

Step 3
Remove the 3 preassembled screws (EE)
from the top of the burner (G). Attach the
glass tube ring (F) to the top of the burner
(G) using the 3 screws removed at the
beginning of this step. Be sure to fully
tighten.
Step 4
Place the glass tube (E) into the top of the
glass tube ring (F).
Step 5
Attach the 3 mesh guards (F) onto the
hooks at the top of the burner (G), attach
the 3pcs M5 nuts (DD) at the bottom of
the mesh guard (F).
11

Step 6
Assemble the reflector (A+B) with screws
(KK) 9pcs and Nuts (HH) 9pcs.
Step 7
Assemble the 3pcs M8X65 double head
screw (LL) on the Heat Insulation plate (C).
Step 8
Assemble the Heat Insulation plate with
flame screen on mesh guard, with 3pcs
M5 nuts (DD).
12

Step 9
Assemble the reflector with 3pcs M8 nuts
(MM).
Step 10
Attach the anchoring arms
(FF) onto the base of the tank
housing (D) using 6 M6 x 12
screws (BB) and 6 M6 nuts
(DD).
13

Operation
To Light
1. Unscrew the ignition button on the burner to see if the
battery (H) has already been placed inside. If the battery (H)
is not already within the ignition button on the burner,
please place the battery (H) into the ignition button slot.
2. Make sure the ignition control knob is turned to the “off”
position. Connect propane gas tank and slowly open the
valve on the propane gas tank by turning the knob counter
clockwise.
3. Press in and turn the ignition control knob to the “pilot”
position; hold down for 1 minute.
4. Push the ignition button, while still holding down control
knob down, to generate a spark.
5. Check to see if there is a pilot light through the glass tube
(E). If there is, turn the control knob to the “low” position.
6. For maximum flame height and output, turn the control
knob to the “high” position.
To Extinguish
1. Push and turn the ignition control knob clockwise to the
“off” position.
2. Turn the propane gas tank valve on the gas tank to close
the gas supply and disconnect the propane gas tank
Warning: If the lighting instructions are not followed directly
a fire or explosion may occur resulting in property damage,
personal injury or death.
14
WARNING
Do not move the heater, or
cover it with a protective cover
until the product has cooled
down.

Replacing the Gas Cylinder
1. Close the valve of the gas cylinder.
2. Disconnect the regulator from the cylinder following the instructions that came with
your regulator.
3. Replace the cylinder.
4. In the absence of any flame, remove the plug or seal cap from the cylinder valve.
5. Check for the presence and good state of the gasket before connecting the regulator.
6. Perform leak test using soapy water solution.
Storage
•Always close the valve of the gas cylinder after use or in case of a disturbance.
•Remove the pressure regulator and the hose attachment if the heater is not to be
used for a period of time.
•Cylinder must be stored outdoors in a well-ventilated area out of the reach of
children.
•Disconnected cylinder must have threaded valve plugs tightly installed and must
not be stored in garage or any other enclosed area.
•Storage of heater indoors is permissible only if the cylinder is disconnected and
removed from the heater.
•Check the tightness of the gas valve and for damage. If you suspect damage, have
it changed by your gas dealer.
•Never store liquid gas cylinder in a sub-terrain, or at places without adequate air
ventilation.
15

Cleaning and Care
Wipe off powder coated surfaces with soft, moist rag and soap water. Do not clean heater
with cleaners that are combustible or corrosive
Remove debris, spider and insect nests from ventilation opening of the cylinder
enclosure, control compartment, burner and circulation air passageways of the heater
with heavy duty pipe cleaner or compressed air to keep appliance clean and safe for use.
Never clear ports or other openings with toothpicks or other article that will break and
block the ports.
If carbon deposits develop, remove the reflector and flame screen and clean them with
soap water. Do not paint the flame screen, control panel or reflector.
Cover the burner unit with the supplied protective cover when the heater is not in use.
Wait until the heater is cool before covering.
In a salt-air environment, such as near an ocean, corrosion occurs more quickly than
normal. Check frequently for corroded areas and repair them promptly.
General Safety
Equip your home with a least one smoke detector on each floor.
Keep at least one dry-powder operative ABC-type Fire
Extinguisher in the home at all times.
Keep areas around heat sources free of papers and trash.
Store paints, solvents, and flammable liquids away from all heat
and ignition sources.
Develop a fire-escape plan before a fire occurs. Be certain every
person understands the plan and is able to carry out the plan in case of emergency.
If your clothing does catch fire don't run. Drop down immediately and roll to smother the
flames.
16

First Aid for Burn
EYES
Seek medical attention IMMEDIATELY. Do not put ointments or liquids in eye.
ELSEWHERE
Consult a doctor if the burn is not healed in 24 hours, or the burn is larger than the size of a
palm.
If serious, send promptly for an ambulance or a doctor.
If possible, run affected area under cold water (not ice or ice water) for 10-15 minutes if
the skin is intact.
Cut and gently lift away any clothing covering the burned area, without pulling clothing
over the burns.
Leave in place any clothing that is stuck to the burns. Do not put any creams or greases on
the burned area.
If the casualty's hands or wrists have been burned remove jewellery if possible without
causing, further injury (rings, watches .and so forth) and place in his pockets. This prevents
the necessity to cut off jewellery since swelling usually occurs as a result of a burn.
Do not pop any blisters. Cover the burn with a light gauze dressing. If blisters pop, apply a
light antibiotic ointment and dress as above.
17

Problems Check List
18

Customer Services:
If you would like further advice or information on your product, ensure you have the
SAP code ready and please get in touch with us at Fire Mountain on the contact
options below:
SAP Code: JH06112001
Phone: [phone] (Mon – Fri 9am to 5pm)
Email: [e-mail]
Address: Alfresia, Vale Mill (Rochdale) Ltd, Robinson Street, Rochdale, OL16 1TA
19
Guarantee
Our products are guaranteed for a period of 2 years from the date of purchase. Products
that develop a fault within this period are covered by our warranty and we will replace
defective parts, or where not available the whole product. The warranty does not apply to
any defect in the goods arising from fair wear and tear, wilful damage, accident,
negligence by you or any third party, use otherwise than as recommended by us, failure to
follow our instructions, any alteration or repair carried out without our approval or has been
the subject of commercial use. Your statutory rights remain unaffected, in particular any
rights you have under the Consumer Rights Act 2015.
If you have a problem with your product within this warranty period please contact our
customer services team.
In the event of changes to the specification of a product and we are not able to replace
parts, we will replace the whole product within the 2 year guarantee period
For products that fall outside of the 2 year guarantee, we will endeavour to provide spare
parts to purchase for as many of the replaceable parts as possible, but cannot foresee
specification changes or upgrades to products or parts outside of the initial 2 year period.