Flexa 3327199 User manual

Bunk bed - White - 190x90 cm
Dimensions
Length - 197cm
Depth - 103cm
Height - 148cm
Weight - 43,5kg
Issue 3 - 02/11/15
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 3327199

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2, 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
IMPORTANT - READ CAREFULLY -RETAIN FOR FUTURE REFERENCE
ASSEMBLY:
Always follow the instruction. Current legislation requires that the high bed / bunk bed must be fitted with 4
safety-rails and a ladder or platform for the upper bunk. The high bed / bunk bed meets the European EN
747:2012 A1:2015 standards for security and durability.
MATTRESS:
This bed is designed to use a mattress size 190 cm long and 90 cm wide. The total thickness must not
exceed 16,1 cm. The mattress top must not pass the marking on the ladder / the post for the safety-rail.
WARNING:
High beds and the upper bed of bunk beds are not suitable for children under six years due to the risk of
injury from falls. Bunk beds and high beds can present a serious risk of injury from strangulation if not used
correctly. Never attach or hang items to any part of the bunk bed that are not designed to be used with the
bed, for example, but not limited to ropes, strings, cords, hooks, belts and bags. Children can be become
trapped between the bed and the wall, a roof pitch, the ceiling, adjoining pieces of furniture (e.g. cupboards)
and the like. To avoid risk of serious injury the distance between the top safety barrier and the adjoining
structure shall not exceed 75 mm or shall be more than 230 mm.
Do not use the high bed / bunk bed if any structural part is broken or missing.
MAINTENANCE INSTRUCTIONS:
Check regulary that all assembly fastenings are properly tightened. Ventilation of the room is necessary in
order to keep the humidity low and to prevent mould in and around the bed.

Leg x4 (84.5x4.3x4.3cm)
2
Components - Parts
Please check you have all the parts listed below
2
Slat x30 (89.7x6.5x1.5cm) Cross bar x32
List for safety rails. x2
(32.2x2.8x1.2cm)
Endrail x4 (87.7x8.9x2.0cm)
6
Endrail x2 (87.7x6.5x2.6cm)
10
Leg x4 (61.8.7x4.3x4.3cm)
Top rail x2 (98.5x6.5x2.0cm)
7Tread x3 (31.8x6.0x2.6cm)
45
9
No. 12-04308451-20
If you have damaged or missing components,
call the Customer Helpline: 0045 7668 8055
31
Endrail x2 (87.7x6.5x2.6cm)
11
No. 12-01203181-20
No. 12-04306181-20
No. 12-01602761-20
No. 12-01508971 No. 12-020087721-20
No. 12-02603181-20
No. 12-02009851-20
No. 12-02608771-20
Ladder side x2
(117.7x6.5x2.0cm)
8
No. 12-02011771-20
No. 12-02608772-20

Components - Parts
Please check you have all the parts listed below
Bedside rail x4 (186.7x8.9x2.0cm)
12 No. 1305-18673-20
3
Safety rail 3/4 x2 (152.9x6.5x2.0cm)
13 No. 12-02015291-20
Safety rail 1/1 x2 (186.7x6.5x2.0cm)
14 No. 12-02018673-20

Please check you have all the fittings listed below
M6x90mm Connecting bolt x8
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
M6 Ø10x14mm Barrel nut x8
B
E
4,5x40mm Chipboard screw x4
C
10x45mm Dowel x22
D
Components - Fittings
Phillips
screwdriver
(medium)
Small
hammer
Ruler/tape
measure
4,0x30mm Chipboard screw x80
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
4
3,0x20mm Chipboard screw x4
FNo. 3901-30020
4,0x50mm Chipboard screw x8
GNo. 3902-40050
ø10mm Cover cap x16
HNo. 3938-00010-2
6,3x90mm Assembly screw x38
INo. 3909-63090
ø7mm Cover cap x32
JNo. 3938-00007-2
4,0x25mm Chipboard screw x1
KNo. 3903-40025
ø10x88mm Connecting double bolt x4
LNo. 3934-10088
ø8mm Cover cap x8
MNo. 3938-000081-2
6,3x22mm Euro screw x1
NNo. 3907-63022
7,0x50mm Confirmat screw x12
ONo. 3908-70050
6,3x70mm Assembly screw x2
PNo. 3909-63070
8x40mm Dowel x68
Q
No. 3930-08040
Bracket x4
R
No. 4007-024
27,5x17x15mm Angle x1
SNo. 4008-020
70x40,5x20mm Angle x2
TNo. 4008-022 No. 3938-00015-2 U
ø16,8x5mm Cover cap x48
No. 3901-45040
No. 3930-10045 No. 3901-40030
No. 3922-06014
No. 3913-06090
No. 4033-004

Assembly Instructions
Step 1
Insert dowels to
bedsides 12 – and to all
the safety rails 13 and
14 . Insert dowels Qto
crossbars 5and top
rails 7.
It may be necessary to
tap the dowel in very
gently with a small
hammer.
Insert the connecting
double bolts Lto all the
short legs 1.
Twist /turn the bolt to
follow the hole ø6,8 mm
Counter sunk 5 mm
hole should face same
direction as bedside
drilling
Step 2
5
D
14
12
13
5
7
D
D
Q
Q
Q
Q
D
x2
x4
x2
x2
x32
Q
1
L
L
Ø5 MM
Ø6,8 MM
Ø6,8 MM
L
bedside
drilling

6
Assembly Instructions
Step 3
Attach top rail 7to
endrail 11 by pushing
the dowels in top rail 7
into the holes in endrail
11 and fasten with 4
screws G. Don’t tighten
too hard.
Insert cross bars 5into
the grooves in endrail
11 and push the dowels
into the holes in endrail
11 . Attach endrail 6to
crossbars 5by pushing
the dowels in crossbars
5to holes in endrail 6.
Attach legs 2to
endrails 6and 11 with
screws I. Fasten with
the allen key.
After attaching the legs,
adjust the crossbars
5by pulling them
downwards out of the
groove in endrail 11 until
there is no gap between
endrail 6and crossbars
5.
Step 4
7
11
11
6
55555555
6
11
2
2
G
I
I
I
I
Step 5
5
x2
x2
x2
G
I

F
Assembly Instructions
Step 6
Attach bedside 12 and
both safety rails 14 to
the bed by placing the
dowels into the holes in
legs 2.
Push barrel nuts B
into the 2 small holes
in bedside 12 . Push
1 connecting bolt A
through each leg 2to
meet barrel nuts Band
then fasten with the allen
key.
Push 4 assembly screws
Ithrough legs 2to
meet the safety rails 14
and then fasten with the
allen key.
Attach bedside 12 to
the bed by placing the
dowels into the holes in
legs 2.
Push 2 barrel nuts B
into the small holes
in bedside 12 . Push
1 connecting bolt A
through each leg 2
to meet barrel nuts B.
Fasten the bolts with the
allen key.
Insert cross bars 5into
the grooves in endrail
10 and push the dowels
into the holes in endrail
10 . Attach endrail 6to
crossbars 5by pushing
the dowels in crossbars
5to holes in endrail 6.
Step 8
7
Step 7
14 14 12
2
2
12 2
2
10
6
5
5
5
5
5
5
5
5
IA
IA
B
B
A
A
B
B
I
A
B
B
12
x2

Assembly Instructions
Step 9
Attach legs 2to
endrails 6and 11 with
screws I. Fasten with
the allen key.
After attaching the legs,
adjust the crossbars
5by pulling them
downwards out of the
groove in endrail 11 until
there is no gap between
endrail 6and crossbars
5.
Attach bedside 12 to
the bed by placing the
dowels attached in Step
1 into the holes in legs
1.
Push 2 barrel nuts B
into the small holes
in bedside 12 . Push
1 connecting bolt A
through each leg 1
to meet barrel nuts B.
Fasten the bolts with the
allen key.
Attach bedside 12 to
the bed by placing the
dowels into the holes in
legs 1.
Push 2 barrel nuts B
into the small holes
in bedside 12 . Push
1 connecting bolt A
through each leg 1
to meet barrel nuts B.
Fasten the bolts with the
allen key.
Step 11
8
Step 10 1
1
6
10
12
1
1
12
1
1
I
I
I
I
B
B
A
A
B
B
A
A
I
A
B
B
12
I
L
A
B

Assembly Instructions
9
1
Step 12
Attach the 2 beds by
placing one bed on top of
the other.
Attach the connecting
double bolts Lin legs
1to the upper bed
by fastening them with
screws Cthrough holes
in legs 2.
Push 2 assembly screws
Ithrough holes in legs
2and attach the safety
rails 13 . Fasten screws
with the allen key.
LADDER CAN BE
POSITIONED LEFT OR
RIGHT!
Assemble the ladder by
attaching the ladder sides
8to treads 9with
screws O.
Attach brackets Rto the
ladder side by fastening
them with screws Eto
holes in ladder sides 8.
Attach angle Sto ladder
side 8with screw N.
13
13 2
2
2
21
1
1
8
8
9
9
9
C
C
C
C
I
O
O
O
O
O
O
N
E
E
R
R
R
R
E
E
S
I
C
R
S
N
O
E
L
L
L
Step 13
Step 14
8
8
11,516,5
FRONT
FRONT

Assembly Instructions
Step 15
Attach the assembled
ladder to the bed. Using
brackets Rattached in
the previous step, attach
the ladder to bedsides
12 . Secure safety rails
13 to the ladder with
screws P. Secure the
brackets Rwith screws
F. Fasten angled
bracket Sattached in
the previous step to leg
2with screw K.
Also, attach angled
bracket Tto both legs
2with screws E.
Place 1 slat 4in the
center of the bed and
two slats 4in both ends
of the bed, 16mm from
bed ends. Follow the
measurements.
Push the bedsides 12
together whilst attaching
slat 4to the bed with 2
chipboard screws E
13
13
2
2
2
12
12
12
12
4
F
F
P
K
E
T
E
E
F
T
K
P
10
Step 16
K
S
832 mm832 mm
16 mm

Assembly Instructions
Step 17
Position the remaining
12 slats 4in the bed
with a distance of 63 mm
between each.
Fasten each slat 4with
2x chipboard screws E
Attach the safety list 3
to the inner side of the
safety rails 13 using
screws E. It should be
positioned in the centre
of the front safety rails
between the slats.
Follow the measurement.
Attach the safety list 3
to the outer side of safety
rails 14 and bedside 12
using screws E. Position
the list to the centre of
the safety rails.
Follow the measurement.
Cover all screws Iand
Awith cover caps U
Assembly is complete.
4
3
13
13
3
14
14
12
13
13
12
14
14
12
3
3
E
E
E
E
E
11
E
E
Step 18
71mm
71mm
63 mm
Max mattress height !
4 4 4 4 4 4 4 4 4 4 4 4 4 4
U

If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk
Ref.no. 44-01428-20 D Stand: 021115 Page 13 (80-12416-20) 12
Assembly Instructions
Note: The two sections
can also be used as two
single beds, as shown in
the picture.
Bunkbed as 2 single beds