Flexispot TT2 User manual

Item No. TT2
Installation Guide

Specifications
Accessory Package
Parts Included
Step 1: Connect the supporting plate with supporting beam
01 02
3
276lbs (125kg) (horizontality)
28.7"-54.3" (730-1380mm)
45.3"-66.9" (1150-1700mm)
0°/60°/70°/80°/90°
Max. Weight Capacity
Column Stage
Height Range
Width Range
Tilting Angle
A B C D E F
Screw
M6
x4 x12 x8 x8 x4 x4
Connect the supporting plate (5) with supporting beam (4) with screws (A) and use allen key (H) to
tighten.
1
23
4
6
5
7
8
9
Attention: The drawings below are for guidance only and they may differ slightly from the product
and fittings received. Please contact our customer service department if you have any queries.
G
x4
H
4x4
x1
Screw
M6
Screw
M6
Screw
St4.2
Screw
St4.2
Cable
ties
Screw
St4.2
1. Foot x2
2. Lifting Column x2
3. Cable Management Tray x1
4. Supporting Beam (with control box) x1
5. Supporting Plate x1
6. Caster (2 with brakes) x4
7. Handset(optional) x1
8. Power Plug x1
9. Handset screw x2
A x4
H
4x4
5
H
A
A
5
4
Step 2: Install lifting columns
Connect lifting columns (2) to supporting beam (4) with screws (B) and use allen key (H) to tighten.
Bx8
F
4x4
4
B
H
2

03 04
Step 5: Install tabletop, handle and handset
Use screws (D) to install the tabletop on the frame, and use four screws (E) to install the handle in
the center of the table. Align it with the edge of the table, and install the handset with screws(9), as
shown in Step 5.
Step 6: Connect all cables to the control box
Fix the wire rope with cable tie (F) and the cable tie can be sticked to the tabletop or use screws (G)
to fix it on the table.
Step 3: Install feet
Connect feet (1) to the lifting columns (2) with screws (C) and use allen key (H) to tighten.
Step 4: Install casters
Install casters (6) on the feet (1). Two casters with brakes are installed on the side of the handle as
the front side of the table, as shown in the picture, and tighten with a wrench.
Cx8
H
4x4
C
H
1
2
6
Without brake
Handle
1
Tighten it
With brake
7
Power port
Port for cable
connected to the
lifting column
A C
H S M 1 M 2
8
D C
Tear off Manage cables Fix it
F
F
F
8
Wire rope
Dx8
Ex4
Fx4 Gx4
D
H
4x4
Loosen
Tighten
Adjust
9
E
Port for
handset
The expansion
distance of the
supporting beam
can be adjusted
according to the
actual use.
Align to the edge
of the table

05 06
Step 7: Install the cable management tray
Firstly, rotate the screws (B) incompletely into the supporting beam (4) , which means do not tighten
them. Next, slide one side of the cable management tray (3) into the screws (B), then press the
other side into the screws (B). Finally, tighten the screws (B) with an allen key (H).
Adjust the tabletop angle
Please adjust the handle according to actual needs, press the handle while turning the table with
two hands to a suitable angle, then to loosen the handle and it will lock the tabletop when you hear
a "pop".
Bx4
H
4x4
Step 2: Buckle in the baffle
Slide one side
Buckle the other side
Tighten
2
3
1
Step 1: The
screws are not
fully tightened
0°
90°
Do not place anything on the table when
adjusting the table so as to avoid damage.
0°/60°/70°/80°/90° Five-range adjustment
Caution nipping hand
Handset Instruction
Height Adjustment
Press "▲" or "▼" to adjust the height.
Anti-collision function
The desk will stop automatically when an obstruction is detected while the desk height adjustment
is in motion.
To adjust the sensitivity of the anti-collision function,
keep pressing "▲ " and "▼" simultaneously for 5s to
alternate between level 1, 2, or 3.
The indicator levels are as follows:
·"A-1" : low sensitivity
·"A-2 " : medium sensitivity
·"A-3 " : high sensitivity
·"A-0 " : switch off the anti-collision fuction.
（Before switching off the function please make sure
there aren't any object under the desk to prevent
potential damage.）
Saving the Height
① Press "M". The display will show "5- ". ② Then press the button "1", "2" or "3".
The current height will be saved to the
corresponding position.
Sit-stand Reminder
① Press "A". 2s later the
display will flash and show "00".
② Press "▲"or "▼" to adjust the
time interval.
③ Press any other button to save
the setting or wait 5s till the
system saves it automatically.
The countdown will then start
automatically.
·Stop: Press and hold "A" for 3s to turn off the reminder.
·Reactivation: during the time interval or the buzz alarming, any operation will start another time loop.
·Snooze: if there’s no operation during the buzz alarm, there will be another reminder in 5 mins. If there
is still no operation during the second alarm the countdown will stop automatically.

07 08
Attention
Waste Disposal
This marking indicates that this product SHOULD NOT be disposed of with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used device, please use the Return and
Collection systems or contact the retailer where the product was purchased. They
can take this product for environmentally safe recycling.
Common Fault Treatment
The following tips will help you detect and eliminate common faults and errors. If you
experience a fault not listed below, please contact your supplier. Only the manufacturer and
certified professionals are capable of investigating and correcting those faults and errors.
1. Power supply: AC100V-240V, 50/60Hz
2. Service Environment: 32-104°F
3. Unplug the power plug before cleaning, and wipe the dust on the surface with a slightly wet
dishcloth when cleaning. Be careful to not let the drops into the internal parts, or into the loose
connector.
4. The electric box contains electronic components, metals, plastics, wires, etc. Ensure you
dispose of it in accordance with each country's environmental legislation. Do not dispose of them
with general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen hazards. Therefore, the
manufacturers will not be liable for any accident caused by this improper action.
8. The slight noise caused by the V-Ribbed belt or brake system within the structure will not have
any effect on the use of the equipment.
9. Corrosive or abrasive materials SHOULD NOT be used to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10.This appliance can be used by children aged 8 years and above. It can also be used by
persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge. However, this is on the condition that they’re given proper supervision or instructions
concerning the use of this appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance.
11. Cleaning and user maintenance SHALL NOT be handled by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a
similarly qualified person in order to avoid a hazard.
13. Please make sure there are no hazardous sources in your operating environment. e.g., do not
litter the tools around. Always be careful to dispose of the packaging materials in order to avoid
any possible danger, e.g. plastic bags are a choking hazard to children.
14. Keep the original package of the equipment if necessary in case of future use in
transportation.
Fault Phenomenon Method
The desktop could not function
Rising at low speed
The desk moving downwards without any operation
Automatically self-reset
Goes down but can’t go up or it goes up but can’t go down.
Upper and lower heights are not enough
The desk cannot be lifted
Overwork (Duty cycle: max 2min on/18min off)
Check if the cables are well connected
Check to see if it is overloaded.
The maximum load capacity is 276 lbs.
Reset
Restart after suspending it for 18 minutes
while still connected to power.