ICWUSA ULTRA ARM Series User manual

Page 1
If you have any questions, please call 1-800-558-4435
ULTRA ARM INSTALLATION - rev 04/22/14 pjm
ULTRA ARM INSTALLATION
Page 1 of 4
Locate the wall stud and mark the top
hole of the Wall Track, drill 11/64 pilot
hole and insert #14 screw and tighten
slightly. Use a level, mark the lower
holes, drill pilot holes and then insert the
#14 screws.
NOTE: #14 Wood screws are supplied with unit. If
installing into metal studs, you will need to replace
these with proper metal stud fasteners
MOUNT ULTRA TRACK TO WALL Remove
small socket
head cap
screw in the
top middle
of the Wall
Track.
Remove
plastic cover.
Insert Slider
into Wall Track
as shown
at left and
replace the
small socket
head cap
screw and
plastic cover.
ATTACH SLIDER TO ULTRA TRACK Once you have adjusted the
slider to the desired height,
tighten down the Track
Slider using the handle on
the slider as shown.
Once tight, make sure the
handle is positioned so that
it is pointing down as far
as possible. Pull and turn
handle to position.
IF MOUNTING TO THE ULTRA WALL TRACK
IF MOUNTING TO A DESK
ATTACH DESKMOUNT TO DESK
Drill a 3/8 hole through the
horizontal surface you intend to
mount to and push the 3/8 stud
on the desk mount through the
hole. Slip the large mounting
washer over the stud from
underneath, add the 3/8 split-
washer, and secure in place
with the 3/8 nylock. Screw stud into desk mount
Desk Desk
Washer Nylock

ULTRA ARM INSTALLATION - rev 04/22/14 pjmPage 2 of 4
ATTACH POLE CLAMP TO POLE
Using the 1/4” hex key,
separate the two halves of
pole mount as shown, place
around pole at the desired
height and reassemble.
IF MOUNTING TO A POLE
ATTACH RADIUS MOUNT TO POLE
Using a 1/8”
hex key wrench
make sure the
set screws in the
radius mount
are pulled out
enough that
the mount will
easily slide
down over the
pole. Tighten
the set screws.
OR
ATTACH UL500 TO W2
Attach to UL500 to W2 wall
mount using 3/8 bolt assembly
and 1” bearing assembly
provided. Insert bolt assembly up
through wall ear. Place 1” bearing
assembly over bolt on other side
of wall ear. Place UL500 over bolt
and bearing and turn bolt until
UL500 is secure and smoothly
turns against the bearing. Beauty
cap
UL500
W2
1” ID bearing
assembly
3/8 bolt
assembly with
3/8 ID bearing
ATTACH UL510 TO W2
Attach to UL510 to W2 wall
mount using 3/8 bolt assembly
and 1” bearing assembly
provided. Insert bolt assembly
up through wall ear. Place 1”
bearing assembly over bolt on
other side of wall ear. Place
UL510 over bolt and bearing
and turn bolt until UL510 is
secure and smoothly turns
against the bearing.
1” ID bearing
assembly
3/8 bolt
assembly with
3/8 ID bearing
Beauty
cap
UL510
W2
ATTACH PARALINK TO W2
Attach to Paralink to W2 wall
mount using 3/8 bolt assembly
and 1” bearing assembly
provided. Insert bolt assembly
up through wall ear. Place 1”
bearing assembly over bolt on
other side of wall ear. Place
Paralink over bolt and bearing
and turn bolt until Paralink is
secure and smoothly turns
against the bearing. Beauty
cap
Paralink
W2
1” ID bearing
assembly
3/8 bolt
assembly with
3/8 ID bearing
ATTACH WALL PLATE TO WALL
Locate the stud and mark the top hole,
drill 11/64 pilot hole and insert #14
screw and tighten slightly. Using a
level, mark the lower hole and drill pilot
hole, insert #14 screw and, with the
unit level, tighten both screws.
NOTE: ICW supplies #14 wood screws. If
installing onto metal studs, you will need to
replace with proper metal stud fasteners.
W2
W3
IF MOUNTING
TO A WALL

ULTRA ARM INSTALLATION - rev 04/22/14 pjm
Page 3 of 4
ATTACH VESA TO UL 500
Mount the
VESA assembly
to the friction
mount by sliding
the connecter into the UL500
pivot block. Using the 5/32” hex
key, secure fl at head screw back
into place.
ATTACH VESA TO MONITOR
Attach the
VESA plate to
your monitor
using the four
4mm screws in
the hardware bag.
ADJUST TILT HANDLES
Use the handles to adjust
the tilt of the monitor.
IF USING UL500
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob to
loosen the slider to adjust
the height of the monitor
on the Paralink.
Adjust the pivot tension
of the ball by gently and
evenly tightening or
loosening the four screws
on the back of the ball
VESA.
Slider Knob
Pivot tension
adjustment
screws
IF USING UL550
ADJUST
PARALINK TILT
Adjust monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
ATTACH PARALINK TO ULTRA ARM
Attach to Paralink to Ultra arm
using 3/8 bolt assembly and
1” bearing assembly provided.
Insert bolt assembly up through
arm. Place 1” bearing assembly
over bolt on other side of arm.
Place Paralink over bolt and
bearing and turn bolt until
Paralink is secure and smoothly
turns against the bearing.
1” bearing
assembly
3/8 bolt
assembly
Beauty
cap
Paralink
Ultra arm
ATTACH TO MONITOR
Attach your monitor to the VESA
plate user the four 4mm screws in
the hardware bag.

ULTRA ARM INSTALLATION - rev 04/22/14 pjm
ULTRA ARM INSTALLATION
Page 4 of 4
ULTRA CORD MANAGEMENT
1.Prepare all cables to route within the arm by placing them
near cavity of arm and bundling together if necessary.
2.Remove cover by unscrewing four socket head cap screws.
Screws are captured by the cover so they cannot fall out.
Once screws are disengaged, pull cover out of arm.
3.Place cables within the channel. Do not block the holes
where screws will engage in arm.
4.Replace cover and tighten screws. Cables should be able to
pull through to desired position if necessary.
IF USING PARALINK KEYBOARD TRAY IF USING ULTRA KEYBOARD TRAY
IF USING UL510
ADJUST TILT & MONITOR HEIGHT
Use the handles to
adjust the tilt of the
monitor.
Adjust the height of
the monitor along
the rails of the 510.
Then tighten in
place using slider
knob.
Slider Knob
ATTACH VESA
Mount the VESA
assembly to the slide
rail by screwing in
the knob through the
rail into the VESA
assembly as shown.
ATTACH TO MONITOR
Attach your monitor to the VESA
plate user the four 4mm screws in
the hardware bag.
ATTACH FLIP UP
1.Remove screws from
drop extension using
5/32” hex key.
2.Align holes in keyboard
tray with screw holes in
drop extension.
3.Attach keyboard tray
using the provided
screws.
ATTACH PARALINK
1.Remove beauty cap on
Paralink.
2.Remove screw using 3/16”
hex key.
3.Slide keyboard tray into
Paralink.
4.Replace screw and tighten.
5.Replace beauty cap.
Beauty cap
Screw