Florida Pneumatic Universal Tool UT8080Q Manual
FLORIDA-PNEUMATIC.COM
Please contact 1-800-356-3392 for further assistance.
Universal Tool
™
UT8080Q / UT8080P
Impact Driver
IMPACT DRIVERS
General Safety Information & Replacement Parts
WARNING: Risk of injury to persons. Read and
understand operation instructions. Always become familiar
with all the instructions and warnings before operating any
pneumatic tool.
TABLE OF CONTENTS
General Safety Information ...........................2
Air Compressor and Air Tool Safety................... 2-3
Tool Specifications .................................. 3
Installation ........................................ 4
Maintenance / Lubrication ............................ 4
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Troubleshooting .................................... 6
Warranty .......................................... 6
Service Parts.......................................7
WARNING:This product contains chemicals known to
the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
WARNING:This product contains lead, a chemical known to
the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
Universal Tool a Division of Florida-Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter FL 33458
7.2.2.3 GENERAL SAFETY RULES
• Multiplehazards.Readandunderstandthesafetyinstructionsbefore
installing,operating,repairing,maintaining,changingaccessorieson,
orworkingnearthepowertool.Failuretodosocanresultinserious
bodilyinjury.
• Onlyqualiedandtrainedoperatorsshouldinstall,adjustorusethe
powertool.
• Donotmodifythispowertool.Modicationsmayreducetheeffec-
tivenessofsafetymeasuresandincreasetheriskstotheoperator.
• Donotdiscardthesafetyinstructions–givethemtotheoperator.
• Donotuseatoolifthetoolhasbeendamaged.
• Warningsshallbegivenagainsttheriskofexplosionorreduetothe
materialbeingprocessed;
• Warningsshallbegivenagainsttheriskofcutting.
7.2.2.4 PROJECTILE HAZARDS
• Failureoftheworkpiece,ofaccessories,orevenofthetoolitselfmay
generatehighvelocityprojectiles.
• Alwayswearimpact-resistanteyeprotectionduringoperationofthe
tool.Thegradeofprotectionrequiredshouldbeassessedforeach
use.
7.2.2.5 ENTANGLEMENT HAZARDS
• Entanglementhazard-choking,scalpingand/orlacerationscanoccur
ifneckware,hairorglovesarenotkeptawayfromtoolandacces-
sories.
7.2.2.6 OPERATING HAZARDS
• Useofthetoolmayexposetheoperator’shandstohazardsincluding
crushing,impacts,cutsandabrasionsandheat.Wearsuitablegloves
toprotecthands.
• Operatorsandmaintenancepersonnelmustbephysicallyableto
handlethebulk,weightandpowerofthetool.
• Holdthetoolcorrectly:bereadytocounteractnormalorsudden
movements–havebothhandsavailable.
• Maintainabalancedbodypositionandsecurefooting.
• Keephandsawayfromrotatingorreciprocationaccessories,spindles
orothermovingparts.
• Releasethestartandstopdeviceinthecaseofaninterruptionofthe
energysupply
• Useonlylubricantsrecommendedbythemanufacturer.
7.2.2.7 REPETITIVE MOTIONS HAZARDS
• Whenusingapowertool,youmayexperiencediscomfortinyour
hands,arms,shoulders,neck,orotherpartsofyourbody.
• Whileusingapowertool,positionyourbodyinacomfortable
posture.Maintainsecurefootingandavoidawkwardoroff-balanced
postures.Changingyourpostureduringextendedtasksmayhelp
avoiddiscomfortandfatigue.
• Ifyouexperiencesymptomssuchaspersistentorrecurringdiscom-
fort,pain,throbbing,aching,tingling,numbness,burningsensation,
orstiffness,donotignorethesewarningsigns.Promptlytellyour
employerandconsultaqualiedhealthprofessional.
7.2.2.8 ACCESSORY HAZARDS
• Onlyusesizesandtypesofaccessoriesandconsumablesthatare
recommendedbythepowertoolmanufacturer.
7.2.2.9 WORKPLACE HAZARDS
• Slips,tripsandfallsaremajorcausesofworkplaceinjury.Beaware
ofslipperysurfacescausedbyuseofthetoolandalsooftriphazards
causedbytheairlineorhydraulichose.
• Proceedwithcareinunfamiliarsurroundings.Hiddenhazardsmay
exist,suchaselectricityorotherutilitylines.
• Thispowertoolisnotintendedforuseinpotentiallyexplosiveatmo-
spheresandisnotinsulatedfromcomingintocontactwithelectric
power.
• Makesuretherearenoelectricalcables,gaspipesetc.thatcould
causeahazardifdamagedbyuseofthetool.
7.2.2.10 DUST AND FUME HAZARDS
• Dustfromsomeworkprocessescancausecancer,birthdefectsor
otherrespiratorydiseases.Riskassessmentofthesehazardsand
implementationofappropriatecontrolsisessential.
• Ifthepneumatictoolisusedinadustlledenvironmentexhaust
aircancauseadusthazard
• Dustsandfumesgeneratedwhenusingpowertoolscancause
illhealth(forexample:cancer,birthdefects,asthmaand/order-
matitis);riskassessmentofthesehazardsandimplementationof
appropriatecontrolsofisessential.
• Riskassessmentshouldincludedustcreatedbytheuseofthetool
andthepotentialfordisturbingexistingdust.
• Operateandmaintainthepowertoolasrecommendedinthese
instructions,tominimizedustorfumeemissions
• Directtheexhaustsoastominimizeddisturbanceofdustinadust
lledenvironment
• Wheredustsorfumesarecreated,thepriorityshallbetocontrol
thematthepointofemission.
• Allintegralfeaturesoraccessoriesforthecollection,extractionor
suppressionofairbornedustorfumesshouldbecorrectlyused
andmaintainedinaccordancewiththemanufacturer’sinstructions.
• Select,maintainandreplacetheconsumable/insertedtoolas
recommendedintheseinstructions,topreventanunnecessary
increaseindustorfumes
• Userespiratoryprotectionasinstructedbyyouremployeroras
requiredbyoccupationalhealthandsafetyregulations;
7.2.2.11 NOISE HAZARDS
• Unprotectedexposuretohighnoiselevelscancausepermanent,
disabling,hearinglossandotherproblemssuchastinnitus(ring-
ing,buzzing,whistlingorhummingintheears);
• Riskassessmentofthesehazardsandimplementationofappropri-
atecontrolsofisessential.
• Appropriatecontrolstoreducetheriskmayincludeactionssuchas
dampingmaterialstopreventworkpiecesfrom‘ringing’
• Usehearingprotectionasinstructedbyyouremployeroras
requiredbyoccupationalhealthandsafetyregulations;
• Operateandmaintainthepowertoolasrecommendedinthese
instructions,topreventanunnecessaryincreaseinnoiselevels;
• Select,maintainandreplacetheconsumable/insertedtoolas
recommendedintheseinstructions,topreventanunnecessary
increaseinnoise.
7.2.2.12 VIBRATION HAZARDS
• Exposuretovibrationcancausedisablingdamagetothenerves
andbloodsupplyofthehandsandarms;
• Wearwarmclothingwhenworkingincoldconditionsandkeep
yourhandswarmanddry;
• Ifyouexperiencenumbness,tingling,painorwhiteningoftheskin
inyourngersorhands,stopusingthepowertool,andtellyour
employer.Youshouldalsoseekmedicaladvicefromaqualied
occupationalhealthprofessional.
• Operateandmaintainthepowertoolasrecommendedinthese
instructions,topreventanunnecessaryincreaseinvibration;
• Select,maintainandreplacetheconsumable/insertedtoolas
recommendedintheseinstructions,topreventanunnecessary
increaseinvibrationlevels;
• Supporttheweightofthetoolinastand,tensionerorbalancer,
becausetheoperatorcanthenusealightergriptosupportthetool.
• Holdthetoolwithalightbutsafegriptakingaccountofthe
requiredhandreactionforces,becausetheriskfromvibrationis
generallygreaterwhenthegripforceishigher.
7.2.3ADDITIONAL SAFETY INSTRUCTIONS FOR PNEUMATIC
POWER TOOLS - AIR SUPPLY & CONNECTION HAZARDS
• Airunderpressurecancausesevereinjury.
• Alwaysshutoffairsupply,drainhoseofairpressureanddiscon-
necttoolfromairsupplywhennotinuse,beforechangingacces-
soriesorwhenmakingrepairs.
• Neverdirectairatyourselforanyoneelse.
• Whippinghosescancausesevereinjury.Alwayscheckfordam-
agedorloosehosesandttings.
• Wheneveruniversaltwistcouplings(clawcouplings)areused,lock
pinsmustbeinstalled.
• Donotexceedthemaximumairpressurestatedonthetool.
• Usewhipchecksafetycablestosafeguardagainstpossiblehoseto
toolandhosetohoseconnectionfailure.
• Nevercarryanairtoolbythehose.
Safety Information
FLORIDA-PNEUMATIC.COM
Please contact 1-800-356-3392 for further assistance.
Safety Information (continued)
AIR COMPRESSOR AND AIR TOOL SAFETY
1. Risk of Bursting. Do not adjust the regulator to result in output
pressure greater than the marked maximum pressure of this air
tool.
2. Ensure the hose is free of obstructions or snags. Entangled or
snarled hoses can cause loss of balance or footing and may
become damaged.
3. Never leave a tool unattended with the air hose attached.
4. Do not operate this tool if it does not contain a legible warning
label.
5. Do not continue to use a tool or hose that leaks air or does not
function properly.
6. Never direct a jet of compressed air toward people or animals.
7. Protect your lungs. Wear a face or dust mask if the operation is
dusty.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
Lead from lead based paint, crystalline silica from bricks
and cement and other masonry products, arsenic and
chromium from chemically-treated lumber.
Your risk from those exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well-ventilated area, and work
with approved safety equipment, such as dust masks that
are specically designed to lter out microscopic particles.
Important Warnings - Impact Drivers
Specications
1. Eye protection and hearing protection and safety gloves must always we worn when operating an impact wrench or
impact driver.
Accessory Hazards
2. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or
accessory.
3. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.
4. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded
fasteners manufacturer; do not use other types or sizes of accessories and consumables.
Vibration Level (m/sec2): 4.58 Noise Level (dBA): 77.63
Motor Motor Torque Speed Head Size and Weight Weight Length Length Rec. Air Inlet Rec. Hose Air Cons Av. Air Cons
Model (HP) (kW) Range (ft. lb.) (RPM) Exhaust Setting Capacity (lb.) (Kg) (in.) (mm) Pressure (NPT) (I.D. in.) (cfm) (cfm)
UT8080Q 0.4 0.29 10-75 10,000 Handle 1/4” Int. Hex 2.3 1.0 6.00 152 90 psi-6.2 bar 1/4” 3/8” 20 5.0
UT8080P 0.4 0.29 10-75 10,000 Handle 3/8” Sq. Drive 2.3 1.0 6.00 152 90 psi-6.2 bar 1/4” 3/8” 20 5.0
Universal Tool a Division of Florida-Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter FL 33458
Installation
1 Cleaning the air hose
□A 3/8" air hose is required, with a maximum length of 25 ft.
□Clean the air hose of accumulated dust and moisture
before connecting it to the air supply.
NOTE: If a longer air hose is required, connect a 1/2" air
hose to the 3/8" air hose to ensure the impact driver has
the necessary air supply.
Recommended Air Line Set-Up
Part Description
AAir Tool
B Quick Plug
C Quick Coupler
D Air Hose
E In-line Regulator
F In-line Lubricator
G In-line Filter
H Air Compressor
Ensure the air line is shut-off and drained of air before removing this tool for service or changing accessories. This
will prevent the tool from operating if the throttle is accidentally engaged.
LUBRICATION
□An in-line lter-regulator-lubricator is recommended as it increases tool life and keeps the tool in sustained
operation.
□Regularly check and ll the in-line lubricator with air tool oil. Avoid using excessive amounts of oil.
□Adjust the in-line lubricator by placing a sheet of paper next to the tool’s exhaust ports and holding the throttle
open approximately 30 seconds. The lubricator is properly set when a light stain of oil collects on the paper.
□If it is necessary to store the tool for an extended period of time (overnight, weekend, etc.), generously lubricate the tool through the air
inlet. Run the tool for approximately 30 seconds to ensure the oil is evenly distributed throughout the tool. Store the tool in a clean and
dry environment.
□Recommended lubricants: Air tool oil or any other high grade turbine oil containing moisture absorbent, rust inhibitors, metal wetting
agents, and an EP (extreme pressure) additive.
Maintenance
FLORIDA-PNEUMATIC.COM
Please contact 1-800-356-3392 for further assistance.
Operation
1 Operating the impact driver
□This Impact Driver has a two-step trigger that delivers
higher speed with increased trigger pressure. The speed is
controlled by the amount of switch trigger depression.
□To turn the impact driver ON, depress the switch trigger.
□To turn the impact driver OFF, release the switch trigger.
2 Changing the rotation direction
□The direction of the bit rotation is reversible.
□Control the rotation direction by moving the side-mounted
switch to Forward or Reverse as required for the operation.
3 Installing and removing the bits
NOTE: It is normal for there to be some play in the installed
bit. Use only impact quality bits with a locking groove.
WARNING: Ensure the bit is secured in the coupler before
using the impact driver. Failure to do so could cause serious
personal injury.
To install the bits:
□Remove the air supply from the impact driver.
□Pull back the ball retainer and insert the bit. Release the
sleeve and the bit locks in place.
□Pull on the bit to ensure it is secured in the coupler.
To remove the bits:
□Remove the air supply from the impact driver.
□With the nose of the tool pointed away from you, pull back
the ball retainer.
□Remove the bit.
4 Driving or removing screws
□Place the rotation direction switch in the correct position
(forward or reverse) for the operation.
□Hold the impact driver with one hand.
□Place the bit on the screw head and slowly depress the
switch trigger. Start the bit slowly for more control.
□As the screw is driven, impacting will begin.
Universal Tool a Division of Florida-Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter FL 33458
Warranty
Limited Warranty: Universal Tool warrants its tools to be free from defects in material and workmanship for one year from the date of
purchase. This warranty does not apply to tools which have been abused, misused, modied or repaired by someone other than Universal
Tool or its authorized service centers. If a UT tool proves defective in material or workmanship within one year after purchase, return
it to any authorized service center or Universal Tool freight prepaid. Please enclose your name, address and adequate proof of date of
purchase and a short description of the defect. Universal Tool will,at its option, repair or replace defective tools free of charge. Repairs or
replacements are warranted as described above for the remainder of the original warranty period. Universal Tool's sole liability and your
exclusive remedy under this warranty is limited to repair or replacement of the defective tool.
There are no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential or special damages,
or any other damages,costs or expenses excepting only the cost or expense of repair or replacement as described above.
Troubleshooting
Problem Possible Cause Solution
The tool runs slowly or will not
operate.
There is grit or gum in the tool. Flush the tool with air tool oil or gum solvent.
The tool is out of oil. Lubricate the tool according to the lubrication
instructions in this manual.
The air pressure is low. □Adjust the regulator on the tool to the
maximum setting.
□Adjust the compressor regulator to the tool’s
maximum setting of 90 psi.
The air hose leaks. Tighten and seal the hose ttings with pipe thread
tape if leaks are found.
The air pressure drops. □Ensure the hose is the proper size. Long
hoses or tools using large volumes of air may
require a hose with an I.D. of ½" or larger
depending on the total length of the hose.
□Do not use a multiple number of hoses
connected together with a quick connect
tting. This causes additional pressure drops
and reduces the tool power. Directly connect
the hoses together.
There is a worn rotor blade in the motor. Replace the rotor blade.
There is a worn ball bearing in the motor. Remove and inspect the bearing for rust, dirt, and
grit. Replace or clean and grease the bearing with
bearing grease.
There is moisture blowing out
of the tool’s exhaust.
There is water in the tank. Drain the tank. (See the air compressor manual
for instructions.) Lubricate the tool and run it until
water is not evident. Lubricate the tool again and
run for 1-2 seconds.
The tool impacts slowly or not
at all.
The tool needs lubricating. Lubricate the air motor and the impact mechanism
according to the lubrication instructions in this
manual.
The tool regulator setting is in the wrong position. Adjust the regulator on the tool to the maximum
setting.
The tool impacts rapidly, but
will not remove bolts.
The tool has a worn impact mechanism. Replace the worn impact mechanism components.
The tool does not impact. The impact mechanism is broken. Replace the broken impact mechanism
components.
FLORIDA-PNEUMATIC.COM
Please contact 1-800-356-3392 for further assistance.
Service Parts / Exploded View Drawing
Ref No. Part Number Description Qty Ref No. Part Number Description Qty
Universal Tool a Division of Florida-Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter FL 33458
Universal Tool
™
Questions, problems, missing parts?
Call Customer Service
8 a.m.-5 p.m., EST, Monday-Friday
1-800-356-3392
FLORIDA-PNEUMATIC.COM
Retain this manual for future use.
This manual suits for next models
1
Table of contents
Other Florida Pneumatic Impact Driver manuals
Florida Pneumatic
Florida Pneumatic FP723 Installation instructions
Florida Pneumatic
Florida Pneumatic FP-777A Manual
Florida Pneumatic
Florida Pneumatic FP-745TCI Manual
Florida Pneumatic
Florida Pneumatic FP-797 Manual
Florida Pneumatic
Florida Pneumatic Universal Tool UT8150P-2 Manual
Florida Pneumatic
Florida Pneumatic Universal Tool UT8365C Manual
Florida Pneumatic
Florida Pneumatic FP-720B Manual
Florida Pneumatic
Florida Pneumatic Universal Tool UT8350C Manual
Florida Pneumatic
Florida Pneumatic FP-793B Manual
