FONESTAR SAV-4 User manual

SAV-4 SAV-6
DESCRIPTION
Loudspeaker mount with suction pads and adjustable safety strap, to install on the roof of a car, van etc.
With holes for horn speaker mods. FE-1210, FE-107, FE-149 or similar. Easy to mount and demount quickly
on any type of vehicle.
WARNING
VERY IMPORTANT:
A) Before assembly, make sure that the suction pads are going to be on a flat surface without indents or
marks that could let air in and therefore prevent them from sticking.
B) Make sure that the surface is lean and dry. The installation of the mount on a dirty or damp surface,
will practically cancel out the adhesive effect of the suction pads. Remove the silicone residue that
polishes in car washes usually leave.
This mount is not suitable for canvas, vinyl, etc. which due to their porosity or movement, make it easy for
air to get under the suction pads.
Dimensions: SAV-4: 31 x 5 x 31 cm depth
SAV-8: 66 x 5 x 18 cm depth
ATTENTION: Although this mount, with horn speakers assembled and correctly fixed, can stay perfectly
in place at a maximum speed of 80 km/hour, it is recommended that you do not go faster than
50 km/hour to avoid damaging the mount, loudspeakers or even the vehicle. Especially when
the wind is blowing strongly from the side or the front.
INSTALLATION
1.- Mount the loudspeakers on the corresponding bars on the mount using the nuts, bolts and washers
supplied.
The connection has to be made in series or in parallel, depending on the impedance of the loudspeaker
or amplifier to be connected.
2.- Position everything, loudspeakers-mount, on the roof of the vehicle. Take into consideration the warnings
in part 2 (WARNING).
3.- Press the system down lightly so that the suction pads stick to the roof of the vehicle. Make sure that
the surface is clean and do not apply any chemical product, adhesives, etc. to the suction pads or the
installation surface.
4.- Pass the safety strap through the corresponding holes in the mount and then through the open door to
the inside of the vehicle. Pass the free end through the strap tensioner and tighten pulling the free end.
5.- Check that everything is firmly attached in place and the doors close properly.
6.- Connect the loose end of the speaker cable to the amplifier output on the car passing it through the
same open door.
EN SAV-4, SAV-6
VEHICLE LOUDSPEAKER MOUNT
SAV-4, SAV-6_MANUAL_(EN)_20171114_Maqueta ión 1 14/11/17 8:12 Página 1

Bear in mind that your vehicle will grow a few centimetres with the loudspeaker and mount on the roof. This
could therefore knock into and damage things, for example garage doors, car washes, etc.
Make sure you remove it whenever you use something like this and in general when you are not using the
PA system.
The materials used to manufacture this mount are weather-proof. However, in extreme heat, salty
atmospheres, etc. some of the components could wear out more quickly, making it stick less effectively
over a period of time. To avoid this, periodically check the state of the rubber, nuts, etc. and replace them
with new ones if necessary.
FONESTAR is a member of EC EMBALAJES ESPAÑA, S.A. “EC EMBES”, with number 03497 and all our products carry the symbol, backed by our membership and subscription to
the above mentioned organization with the recycling and subsequent management of our packaging.
FONESTAR is registered in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI (Registro de establecimientos Industriales), with the entry number 001851.
Manufactured in Spain - F NESTAR S.A. - NIF A28780443 - Poligono Trascueto - 39600 Revilla de Camargo, Cantabria (Spain)
www.fonestar. om
WARRANTY
This product has been tested and has passed the corresponding quality control prior to being put on the market.
FONESTAR guarantees the suitability of the product for its specified use during a period of 2 years from the delivery date and commits
itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General para la Defensa de los Consumidores y Usuarios,
Real Decreto Legislativo 1/2007 16 Noviembre.
The lack of conformity in the first six months after purchase, due to a manufacturing defect, will be rectified with no more than showing
the proof of purchase. After six months FONESTAR reserves the right to demand proof of the product being sold with that problem.
This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts due to use, breakages,
burns, spilt liquids or other substances, excessive humidity, battery deterioration and internal manipulation of the device, the software
or its components by unauthorized persons, and in general any use that is unrelated to the nature and purpose of the product.
If any service is needed during the warranty period because of lack of conformity, please contact the business or distributor where the
product was purchased in no more than 2 months after being conscious of the problem. It is only necessary to contact FONESTAR if
it is impossible or imposes an undue burden for them to solve it.
To benefit from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no corrections or crossing
out.
This document adds information, and never decreases the consumers’ rights, which in all cases are protected by the Spanish law ‘La
Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.
SAV-4, SAV-6_MANUAL_(EN)_20171114_Maqueta ión 1 14/11/17 8:12 Página 2