Fortress Technologies Al13 HOME User manual

1/12
13
Installation Instructions for Fortress Al HOME
Traditional Panels with Straight Brackets
13
and Al HOME Posts
Required Materials
Miter saw with carbide fine blade, T-25 driver bit, #2 phillips head screwdriver, #2 phillips head bit, 1/8” drill bit, 5/16” nut
driver bit, bit extender, tape measure, socket set, speed square, touch up paint, crescent wrench, level, framing square,
eye protection, and other personal protective equipment.
It is the responsibility of the installer to meet all code and safety requirements, and to obtain all required building permits.
The deck and railing installer should determine and implement appropriate installation techniques for each installation
situation. Fortress Railing Products and its distributors shall not be held liable for improper or unsafe installations.
13 13
Fortress Al HOME posts must always be secured to the deck framing. Fortress Al HOME posts should never be
attached to only the deck boards.
Read Instructions Completely Before Starting Installation
Note
When cutting Fortress railing, it is very important to complete the following at cut points:
• Remove all metal shavings from the cut area.
• File any sharp edges left by cutting. Thoroughly wipe and remove any filings, grime or dirt from the railing.
• Apply two coats of Fortress zinc based touch-up paint to the cut area. If touch up is at rail ends, allow paint to dry before
connecting bracket to post.
• Be sure to remove any metal shavings from the surface of deck, patio or balcony to prevent stains on the deck surface.
Torx Safety Tips
• Always use the lowest speed setting on drill.
• To reduce chance of bit breakage, start tightening with drill on low torque setting and work up until screw is secured.
• Tip: Pre-drill holes with 1/8” drill bit.
REV 032718
13
*Reference Fortress Al HOME post mounting instructions
1/2” minimum
Added Blocking
13
Mount Al HOME Posts*
• Wood blocking tied to deck frame must be installed and constructed with treated dimensional lumber with a minimum
thickness of 1-1/2”.
13
• Position the edge of Al HOME base plate a minimum of ½” from the inside edge of rim joist.
13
• Mount Al HOME posts at appropriate points based on panel length.
13
• Attach Al HOME posts with 3/8” X 3-1/2” hex head galvanized bolts.
Base plate barrier
must remain between
post and deck surface

Option Two: Proud Post
Option One: Over The Post (OTP)
Round Accent Top Rail
Flat Accent Top Rail
Post Pre-attached
Straight Brackets
Post Pre-attached
Straight Brackets
Post Pre-attached
Straight Brackets
Post Pre-attached
Straight Brackets
3” Post3” Post
I-Support
Post Base
Cover
Post Base
Cover
Post Cap Post Cap
13
Al Home Panels 69.5” or 93.5”
I-Support
Post Pre-attached
Straight Brackets Post Pre-attached
Straight Brackets
Post Base
Cover
13
Al Home Panels 69.5” or 93.5”
Post Base
Cover
Flat Accent Top Rail
Round Accent Top Rail
2” Post 2” Post
Post Pre-attached
Straight Brackets
Round ATR
Line Splice
Flat ATR
Line Splice
Post Pre-attached
Straight Brackets
Round ATR
End Splice
Flat ATR
End Splice
2/12

OTP and Proud Post: Max Post Spacing
• 8’ panel maximum post spacing is 93-7/8”.
• 6’ panel maximum post spacing is 69-7/8”.
Note: Do not exceed the maximum post spacing.
8’ Panel max post spacing 93-7/8”
6’ Panel max post spacing 69-7/8”
OTP and Proud Post: Measuring The Panel Opening Length
• Measure the distance of the panel opening.
• Measure from the back wall of the bracket to the back wall of the bracket on other post.
• Confirm that the measurements for the top brackets are the same as the bottom brackets.
Measure the panel opening
Not here
Measure from
back of bracket
Check measurement with top
3/12

Fortress Railing products can be
cut with a circular saw or miter saw
with a metal cutting blade
Remove any metal shavings and dust
with a brush or rag. Make sure
surfaces to be painted are clean.
Using a piece of cardboard as a mask,
apply the 1st coat of Fortress zinc
based touch-up paint. Allow to dry
before applying second coat.
1st Coat 2nd Coat
Using a piece of cardboard as a mask,
apply the 2nd coat of Fortress zinc
based touch-up paint. Allow to dry
and install.
OTP and Proud Post: Cut Down Panel to Correct Length
• To insure both ends of the panel look the same, divide the bracket to bracket measurement by 2 to find half of the panel
length.
• Find the center of the panel and measure out half of the length each direction.
• Mark these locations with a paint pen or other tool on the top and bottom rail.
If installing an Over The Post railing continue on page 5.
If installing a Proud Post railing continue on to page 9.
After cutting panel,
file cut edges smooth
*Top rail cover can slide*
Make sure the cover lines
up with the end of the rail
before cutting down the panel
Center of Panel
Half of the panel length Half of the panel length
Mark here
Mark here
Mark here
Mark here
4/12

Over the Post: Installing the Panel & I-Support
• Install the panel I-support by twisting it into the center of the bottom rail . Position the I-support so directly under a baluster
the attachment screw can be easily installed on the deck.
• Insure that all panels are at the same height before attaching them to the post. The use of an ATR spacer or block might be
needed to measure over a post. See the images below.
• It is recommended that all panels are attached with provided screws on the same side of the bracket when using
a line post.
• Attach the panel to each of the 4 brackets using the provided self-drilling screw with a T25 bit.
Tip: Pre-drill with a 1/8” drill bit.
I-support
5/12

Over the Post: Accent Top Rail (ATR) Spacers
• The accent top rail kit comes with 7 spacers in the 93.89” Kit and 6 spacers in the 69.89” Kit.
• The spacers should be equally spaced along the length of the rail, with no more then 14” spacing between them.
• The end spacers should be placed as close to the end brackets as possible.
• Attach spacers using provided self-drilling screws with a 5/16” nut driver. Two screws per spacer.
• Do not remove backing of double sided tape until you are ready to permanently attach the ATR.
Double sided
tape
Spacer attached
next to bracket
14”
Max
Over the Post: Accent Top Rail Line and End
• Measure the distance from the inside edge of the 2 posts.
• Cut the ATR to this length using the same steps as used for cutting down a panel.
• The ATR cannot block the inside edge of the post.
• When test fitting the ATR, place on top of the spacers. Do not press the ATR down over the spacers. Removing the
ATR from the spacers can damage the ATR and spacers.
• Remove the backing of all of the double-sided tape on the ATR spacers.
• Using force, the ATR snaps down around the ATR spacer.
• See next page for corner ATR installtion.
ATR cannot
go past this line
6/12
ATR should not go past
this point when test fitting

Over the Post: Accent Top Rail Corner
• When installing ATRs on corners with a 2” post, the ATR must be 5/16” away from the post.
• If installing a corner with a 3” proud post, install the ATR at full length from the inside edge of the post to the inside edge
of the post.
5/16” Minimum
5/16”
Minimum
2” Post 3” Post
Over the Post: ATR Splice
• ATR splices reference the inside of the post and snap down around the ATR.
• ATR splices allow up to 1/2” of length variation from the edge of the post.
• To install a ATR splice: Center the splice over the post and with force press down over the ATR.
• A mallet might need to be used to instal. If using a mallet, use a cloth to protect the splice from damage.
1/2” 1/2” 1/2”1/2”
1/2”
ATR
ATR
7/12
ATR with 2” Post Splice
Over The Post
ATR with 3” Proud Post
Over The Post

Over the Post: Cap Rail Clips
• Install top rail bracket covers that come with the cap rail clips.
• Use cap rail clips when installing a drink rail.
• Cap rail clips should be equally spaced over the panel length.
• It is recommended to pre-drill the screw holes especially if the drink is a
composite rail.
Cap rail clip
Top cap installation when
installing a drink rail
Over The Post: Bracket Cover and Post Base Cover
• Bracket caps snap down over bracket cups.
• Use a #2 phillips head screw driver to attach the two halves of the post base cover.
• Use a broom or compressor to remove debris from railing and deck surface.
13
End of Al HOME Over The Post Installation
8/12

Proud Post: Installing the Panel & I-Support
• Install the panel I-support by twisting it into the center of the bottom rail . Position the I-directly under a baluster
support so the attachment screw can be easily installed on the deck.
• Attach the panel to each of the 4 brackets using the provided self-drilling screw with a T25 bit.
Tip: Pre-drill with a 1/8” drill bit.
• Attach the panel I-support to the deck surface using the provided phillips head screw.
I-support
9/12

Proud Post: Bracket Caps
• Bracket caps snap down over bracket cups.
• If you are installing a drink rail using the cap rail clips, the cap is installed under the bracket. See page 11 for details.
• The top bracket cap can be installed when using an ATR, but is not required to be installed.
Proud Post: Accent Top Rail Spacers
• The accent top rail kit comes with 7 spacers in the 93.89” Kit and 6 spacers in the 69.89” Kit.
• The spacers should be equally spaced along the length of the rail, with no more then 14” spacing between them.
• The end spacers should be placed as close to the end brackets as possible.
• Attach spacers using provided self-drilling screws with a 5/16” nut driver. Two screws per spacer.
• Do not remove backing of double sided tape until you are ready to permanently attach the ATR.
Spacer attached
next to bracket 14”
Max Double sided tape
10/12

Proud Post: Installing Accent Top Rail
• Measure the distance from the inside edge of the 2 posts.
• Cut the ATR to this length using the same steps as used for cutting down a panel.
• When test fitting the ATR, place it on top of the spacers. Do not press the ATR down over the spacers. Removing the
ATR from the spacers can damage the ATR and spacers.
• Remove the backing of all of the double-sided tape on the ATR spacers.
• Using force, the ATR snaps down around the ATR spacer.
Proud Post: Cap Rail Clips
• Use cap rail clips when installing a drink rail.
• Cap rail clips should be equally spaced over the panel length.
• It is recommended to pre-drill the screw holes especially if the drink will be a
composite rail.
Cap rail clip
Top cap installation when using
cap rail clips to install a drink rail
11/12
ATR should not go past
this point when test fitting

13
Proud Post: Al HOME Post Cap
13
• Al HOME post cap is press fit into place.
• Follow the Fortress accents Instructions for fitting the post cap.
13
Proud Post: Al HOME Post Base Cover
• Use a #2 phillips head screw driver to attach the two halves of the post base cover.
• Use a broom or compressor to remove debris from railing and deck surface.
13
End of Al HOME Proud Post Installation
12/12