Systemline Mk2 User manual

Standard 4 zone enclosure Mk2
4 zone standard enclosure to house 2 NetAmps,
1 NetServer / Mini NetServer, 1 NetPower
Amplifier and up to 2 10 Port USB Hubs SN8401

Pack contents
Wall panel x 1
Extension hooks x 2
NetAmp
(each unit includes
2 brackets & 4 screws)
Screws (M4x10mm Pozi) x 26 Cable ties x 20Screws (M3x6mm Pozi) x 8
Mounting box x 1
10 port USB hub 6 way mains extension
Shelf x 1
NetServer
(each unit includes
2 brackets & 4 screws)
Cover x 1
NetPower
(each unit includes
2 brackets & 4 screws)
Mini NetServer
Systemline® is a registered trademark of Armour Home Electronics Ltd. Velcro® is a registered trademark of Velcro Industries
B.V. and its aliates. All other product names are trademarks or registered trademarks of their respective owners.
A
E
I
F G H
B
J
C
K
D
L
M N
Supplied separately

A
A
B
C
D
Installation instructions
1. Lift and pull cover to remove. Detach shelf and cable box from wall panel by unscrewing 2 shelf screws and 2
mounting box screws.
2A - Individual cabinet. Check available space*and mark position of centre hole. Drill centre hole for your wall
xing**.Insert wall xing and hang wall panel from it. Mark position of 4 main mounting holes. Proceed to step 3.
*All dimensions in mm
**Wall xings not supplied
2B - Additional cabinets. Fit 2 extension hooks onto new wall panel using 4 M4x10 screws provided. Hang wall
panel beneath existing cabinet using 2 hooks for alignment. Proceed to step 3.
E
E
44
247.5
560
247.5
Fx4

4. Hang shelf from wall panel using 2 tabs at rear of shelf and x in place using 4 M4x10 screws provided.
5. Fit mounting brackets to NetPower and NetServer. Place each item onto shelf and secure using 8 M4x10 screws
provided.
J
J K
L
C
L
3. A cut-out is provided in the wall panel for a single/double gang mains socket and/or cable entry. Fit mains socket
and drill required cable entry holes through wall. Secure wall panel to wall using 4 wall xings**.
x4
**Wall xings not supplied
F
x8
F

x8
x2
6. Secure up to 2 USB hubs to underside of shelf using 4 M3x6 screws supplied for each hub.
M
G
8. Fit mounting brackets to both NetAmps. Fix each NetAmp to mounting box using 4 M4x10 screws provided.
Feed NetAmp mains leads through from rear of mounting box using holes provided and plug into NetAmps.
7. Fit power supplies for NetServer / Mini NetServer / USB hubs onto wall panel either side of cable entry cut-out.
Secure PSUs using cable ties in the mounting positions provided and connect cables.
H
I
B
x2
x8
F

M
10. Sit mounting box onto wall panel using 2 lower tabs on mounting box. Fix to wall panel using 2 M4x10 screws
provided.
11. Plug all mains plugs into 6 way mains extension and connect cables between products* as required. Use cable
ties in mounting positions provided to keep cables tidy after installation.
x2
F
G
9. Secure 6 way mains extension onto mounting box using cable ties. Mains extension should rest on tabs provided
for extra security. Plug 6 way power socket into wall socket before screwing mounting box into place.
NTo 6 way mains extension
H
*See manual supplied with each product for connection details

12. Fit cover by pushing 4 xing tabs through 4 cut-outs in wall panel. Push cover rmly on both front edges to
engage all 4 xing tabs and slide downwards to secure in place.
D

Stortford Hall Industrial Park
Dunmow Road
Bishops Stortford
Hertfordshire
CM23 5GZ
United Kingdom
www.armourhome.co.uk
©2016 Armour Home Electronics, All rights reserved.
Our policy is one of continuous product improvement. We reserve the right
to change the design and specications without notice.
All information is given in good faith. The manufacturer accepts no
responsibility for errors, omissions or incorrect assumptions. Q15463-IS_r3