Fortress Technologies Evolver User manual

FENCING INSTALLATION: EVOLVER
1
EVOLVER ALUMINUM FRAMED COMPOSITE FENCING
INSTALLATION INSTRUCTIONS

2
FENCING INSTALLATION: EVOLVER
TABLE OF CONTENTS
English
 Introducon.........................................................................3
 FenceLayout........................................................................5
 PostInstallaon....................................................................7
  NotEmbedded.........................................................7
  Embedded................................................................9
Rail&FenceBoardInstallaon..........................................11
 45oDegreeConverterInstallaon......................................14
Care&Maintenance..........................................................16
 Warranty............................................................................17
AboutCaliforniaProposion65:
hps://fortressbp.com/about/californiaproposion65

FENCING INSTALLATION: EVOLVER
3
INTRODUCTION
READ INSTRUCTIONS COMPLETELY BEFORE
STARTING INSTALLATION
It is the responsibility of the installer to meet all code and
safety requirements, and to obtain all required building
 permits.Thefenceinstallershoulddetermineand
 implementappropriateinstallaontechniquesforeach
 installaonsituaon.FortressBuildingProductsandits
distributors shall not be held liable for improper or
 unsafeinstallaons.
Before You Begin
Contact your local Building Code Department for required
 permitsandlawsregardingyourfenceproject.
 Ifapplicable,alsocontactyourHomeOwnersAssociaon
 forrulesandregulaonsregardingfenceinstallaonsin
 yourneighborhood.
 Call811beforeyoudigpostholestolocateandidenfy
 anyburiedulies.
Components
Locking Clip
Side Rail Support
Fastener Post Slide Cover
TopRailPost BoomRail
Intermediate Rail
45oConverter
70-7/8”
[1800mm]
Post BasePost Cap
Fence Board
70-1/2”
[1791mm]

4
FENCING INSTALLATION: EVOLVER
Customizable Panel Styles
Privacy
Semi-Privacy Reinforced Decorave
Standard Panel Style
Portal
Required Tools
Goggles
Drill
Tape
Measurer
Level
Tool
Speed
Square
Spray Paint
Miter or
Circular Saw
#2Phillips
Head Bit
Bit
Extender
Socket
Set
Pencil
Rubber Mallet
Safety
Gloves
StringGround Stakes
Post Hole
Digger
Spade
Shovel
Concrete/
Gravel
Wheelbarrow
Pliers
DrillBits:
1/16”[2mm]
Hand saw

FENCING INSTALLATION: EVOLVER
5
FENCE LAYOUT
Step 1: Sketch Layout of Fence Perimeter
 1. Idenfythepropertylineanddeterminetheperimeterof 
 yourfenceproject.
 2. Using a tape measure, determine the length of each
  fencerun.
 3. EvolverFenceiseasiesttoinstallwhenstarngfroma
  corner.Ifnogatesareused,onlyoneboardineachline 
 shouldneedtobecut.
 4. Usethegraphonpage6tosketchoutyourfenceproject.
Fig.1
Corner
Post
Corner
Post
Line
Post
TOP VIEW
HOUSE End Post

6
FENCING INSTALLATION: EVOLVER

FENCING INSTALLATION: EVOLVER
7
POST INSTALLATION: NOT EMBEDDED (EXISTING FOUNDATION)
Required Components:
• Post Base (Not Embedded)
• Post
• Fastener
Note:
• Components can ONLY be purchased separately, not as
 partofafullkit.
Step 1: MountPostBase(NotEmbedded/ExisngFoundaon)
 1. Ifinstallingonaconcretepao,conrmthatthe
  paoislevel.
 2. CreateaperimeterforthefenceusingGroundStakes&
  GuideString.Iflayouthas90°corners,conrmthatcorners
  form90°angles.AsshowninFig.1.
 3. PosionPostBasesincornersalongGuide String.
 4. DeterminespacingrequiredbetweenCorner&LinePost 
 Bases.Spacing between each Post Base CANNOT exceed
73”[1860mm](FenceBoardwidthis70-1/2”[1791mm]).
Layout post spacing so that minimal panel cuts are
  required.AsshowninFig.2.
 5. Oncespacingisconrmed,Usepenciltomarkposionof 
 eachpostbase.
 6. Use3/8”[9mm]ConcreteAnchorstoanchorPostBasesto
 foundaon.AsshowninFig.3.
 7. UsealeveltoconrmthateachPostBaseismounted 
 straightata90odegreeangle.
Fig.1
90o
90o
90o
90o
HOUSE Ground Stake
Foundaon
Guide String
TOP VIEW

8
FENCING INSTALLATION: EVOLVER
sewerage lines, that may run across them.
You may wish to check that you are not
digging into them.
STEP 2.1
Slide your post over the mount.
STEP 2.2.
Use a screw to fasten your post to your mount.
Installation Guide - 2017 4
Fig.2
Fig.3 SECTION
VIEW
TOP VIEW
Line Post Base
Corner Post Base
Step2:Mount Post (NotEmbedded/ExisngFoundaon)
 1. SlidethePostoverthemountedPostBases.
AsshowninFig.1.
 2. Be sure to have each fence board slot facing the slot of
 theoppositepost.AsshowninFig.2.
 3. Usealeveltoconrmthatthepostismountedat
90
odegreeangle.
 4. Pre-drillscrewholesintoPostBase&Postwith
  a1/16”[2mm]drillbit.
 5. Useadrilltofastenscrews into the post to the mounted
 postbase.AsshowninFig.3.
Note:
 • Closedwallsidesareaesthecallybestposionforforward
 facingposts.
 • PostSlideCoverscanbeusedtocoverunusedfenceslots.
Max.Post Base Spacing is 73”[1860mm].
Fence Board Width is 70-1/2”[1791mm].

FENCING INSTALLATION: EVOLVER
9
When slotting the post over the post mount. Make certain that your rail slots are facing in the
correct direction for your fence boards.
Installation Guide - 2017 5
When slotting the post over the post mount. Make certain that your rail slots are facing in the
correct direction for your fence boards.
Installation Guide - 2017 5
Fig.1 Fig.2
Fig.3
Opposite
Fence
Board Slots
Opposite Fence
Board Slots
TOP VIEW
Step 1: Mount Post Base (Embedded/NoFoundaon)
 1. Create a perimeter for the fence using Ground Stakes &
  GuideString.Iflayouthas90°corners,conrmthatcorners
  form90°angles.Asshownonpage7,Fig.1.
 2. PosionPostBasesincornersalongstring.
 3. Determine spacing required between Corner & Line Post
 Bases.Spacing between each Post Base CANNOT exceed
73”[1860mm](FenceBoardwidthis70-1/2”[1791mm]).
Layout post spacing so that minimal panel cuts are
  required. AsshowninFig.1.
 4. Oncespacingisconrmed,Usespraypainttomark
  postholelocaons.
 5. Holesshouldbe10”[250mm]indiameter.Checklocal 
 buildingcodesforpostholedepth.
 6. PlaceEmbeddedPostBaseintoholesalongGuideStrings. 
 Postsshouldhaveatleast12”[300mm]exposed
POST INSTALLATION: EMBEDDED (NO FOUNDATION)
SECTION
VIEW

10
FENCING INSTALLATION: EVOLVER
Fig.2
Gravel
Concrete
Post Base
SECTION VIEW
11-13/16”
[300mm]Max
Check
Local Code
  aboveground.Besuretocheckthatpostsarealigned 
 alongguidestrings&posionedcorrectly.
 7. Pourconcreteintoholesandletitsele.
AsshowninFig.2.
 8. Asconcreteseles,Usealeveltoconrmthateachpost 
 baseismountedstraightata90odegreeangle.
Note:
• Some boundary lines may have service lines, electrics and
 seweragelines,thatmayrunacrossthem.Youshould 
 checktoconrmthatyouarenotdiggingintothem.
Fig.1
Max.Post Base Spacing is 73”[1860mm].
Fence Board Width is 70-1/2”[1791mm].
Ground Stake
Guide String
Post Base
Step2:Mount Post (Embedded/NoFoundaon)
 1. ReferencePostMounnginstruconsonpage8,step2.
HOUSE