Fountain TECH FT-70 User manual

FT-70 Flow Chart
28”
24”
20”
16”
12”
8”
4”
H
E
I
G
H
T
13 26 39 52 65 78
I. Introduction
Fountain Tech pumps are carefully inspected and tested to insure
both safety and operating performance. However, failure to
follow the instructions and warnings in this manual may result
in pump damage and/or serious injury. Please read and save this
manual for future reference.
II. Performance
° A clogged or dirty intake screen will greatly reduce perfor-
mance. If the pump is used on a dirty surface, raise it slightly to
reduce the amount of debris contacting the Intake.
Fountain TECH FT-70 Pump
WARNING
° This pump is supplied with grounding connector and a
grounding type attachment plug. To reduce the risk of electric
shock, connect only to a properly grounded outlet.
° Do not remove the grounding pin from the plug.
° Do not connect any voltage other than that shown on the
pump.
° Do not pump ammable liquids.
° The National Electric Code requires that a Ground Fault
Circuit Interrupter (GFCI) be used in the branch circuit supply-
ing fountain pumps and other pump equipment. See your local
electrical supplies dealer for this device.
° To reduce the risk of electrical shock, use only on portable
self contained fountains no larger than 5 feet in any dimension.
° Do not use with water above 86° F.
Failure to observe any of these safety precautions may result in
pump damage and/or serious injury.
Gallons Per Hour
CAUTION
ALWAYS DISCONNECT THE PUMP FROM THE ELECTRI-
CAL OUTLET BEFORE HANDLING.
DO NOT LET THE PUMP RUN DRY.
DO NOT LIFT THE PUMP BY THE POWER CORD.
DO NOT PUMP HEATED LIQUIDS.
OPERATE IN FRESH WATER ONLY.
OPERATE PUMP COMPLETELY SUBMERGED FOR PROPER
COOLING.
° If less ow is desired, adjust the ow control lever on the side of
the pump or restrict the discharge ow.
° Do not allow the pump to run when not submerged. Doing so may
damage the pump. Always submerge the pump rst and then plug in
the electrical cord.
° It is common for there to be air in the pump and tube when rst
plugged in. Pull the electrical cord out and re-insert it until the uid
begins to ow.
° This pump comes with multiple connector tubes. If desired, re-
move and insert other size.
III. Maintainance
To clean the pump, remove the front plate and the impeller. Use a
small brush or stream of water to remove any debris. CAUTION:
The pump shaft can not be removed. IF THE PUMP FAILS TO
OPERATE, CHECK THE FOLLOWING:
° Check the circuit breaker and try another outlet to insure the pump
is getting power. NOTE: Always disconnect the pump from the
electrical outlet before handling the pump.
° Check the pump discharge and tubing for kinks and obstructions.
Algae buildup can be ushed with a garden hose.
° Check the inlet screen to insure it is not clogged with debris.
° Remove the pump inlet to access the impeller area. Turn the rotor
assembly to insure that it is not broken or jammed.
° Monthly maintainance will add to your pump’s life.
NOTE: Insure that the electrical cord loops below the electrical
outlet to form a “Drip Loop”. This will prevent water from running
down the cord into the electrical outlet.
FT-70.indd 1 1/4/2008 6:01:22 PM

FT-70 Mini Submersible Pump
Users Guide
Copyright 2003 Fountain TECH
Warranty
Fountain TECH guarantees this product for
a period of 12 months. Guarantee is void
if the product is misused or tampered with.
Customer must include receipt with
defective pump. If the pump is found to be
defective, Fountain TECH will repair it or re-
place it with a new one.
Please keep this for your records;
Date of purchase ________________________
Model No ________________________
Name of Dealer ________________________
FT-70 Submersible Pump
Fountain TECH
2351 Thompson Way, #C-2
Santa Maria, CA 93455
[phone]
www.fountaintechpumps.com
FT-70.indd 2 1/4/2008 6:01:23 PM