Foxfury Lighting Solutions Tacswan EXOLANDER 700-XLS-II User manual

EXOLANDER©SYSTEMS
FOR AUTEL EVO II
700-XLS-II | 700-XPS-II | 700-XSS-II | 700-3AR-II | 700-XSPS-II
PRODUCT MANUAL

2
TABLE OF CONTENTS
EXOLANDER©Systems
3
EXOLANDER©Landing System
Reference Guide
Physical Characteristics
Installation
4
5
5-7
D100 Drone Spotlight©
Reference Guide
Physical Characteristics
Battery
Operational Modes
Installation
8
9
10
10
11-12
Manual Payload Delivery System©
Reference Guide
Physical Characteristics
Installation
Payload Delivery
Recommended Payload for Delivery
13
14
14-15
15
16
CARE/CLEANING
17
WARNINGS/WARRANTY
17-18
CONTACT FOXFURY
18

3
EXOLANDER©SYSTEMS
EVO II
Saddle
Mount©
EXOLANDER©
Landing
Skids
Manual
Payload
Delivery
System©
D100
Drone
Spotlight©
EXOLANDER©
Landing System
for EVO II
P/N 700-XLS-II
- - -
- - -
EXOLANDER©
Payload System
for EVO II
P/N 700-XPS-II
- - -
EXOLANDER©
Spotlight System
for EVO II
P/N 700-XSS-II
- - -
Autel
EXOLANDER©
System for
EVO II
P/N 700-3AR-II
- - -
EXOLANDER©
Spotlight &
Payload System
for EVO II
P/N 700-XSPS-II

4
EXOLANDER©LANDING SYSTEM
REFERENCE GUIDE
Locking Knob &
Screw (2 ea)
Payload Delivery
Mounting Slot
(4 ea)
External Accessory
Snap Lock Mount
(4 ea)
D100©Mounting
Hole (4 ea)
EXOLANDER©
Mount Connector to
Saddle Mount©(4 ea)
EXOLANDER©Landing
Foot with Slot (4 ea)
LANDING SKIDS*
Tab (4 ea)
per Skid
EXOLANDER©HALF
EVO II SADDLE MOUNT©
Snap Lock (7 ea)
Alignment Pin
( 2 ea)
Alignment
Slot
Threaded Locking
Nut Insert
Locking Knob
& Screw
EXOLANDER©ASSEMBLED
*Not included in P/N 700-3AR-II

5
PHYSICAL CHARACTERISTICS
DIMENSIONS
WEIGHT*
EVO II Saddle Mount©
2.52 x 3.4 x 3.5 in
(64 x 86 x 89 mm)
1.0 oz (28.3 g)
EXOLANDER©,
assembled
6.7 x 6.5 x 4.7 in
(170 x 165 x 120 mm)
4.05 oz (114.7 g)
Landing Skid
8.66 x 0.96 x 0.6 in
(220 x 24.3 x 15 mm)
0.45 oz (12.8 g)
per skid
*Total Weight is 5.95 oz (168.6 g).
EXOLANDER©LANDING SYSTEM
INSTALLATION
❶Install Saddle Mount©on EVO II.
1. Slide the Saddle Mount©on EVO II and make sure that the two
extensions fit behind the front arms of the EVO II and press down.
WHAT'S INCLUDED
EVO II Saddle Mount©
EXOLANDER©
Landing Skid (set of 2)*
*Not included in P/N 700-3AR-II
WARNING
It is the responsibility of drone/UAV users to follow the FAA and global laws and
regulations
and/or the laws and regulations applicable to the flight location.

6
❷Install EXOLANDER©on Saddle Mount©.
1. Place EVO II with Saddle Mount©upside down on a flat surface.
2. Align the EXOLANDER©Half with Snap Lock locations on Saddle
Mount©and slide in the EXOLANDER©Half at an angle as shown
below. Make sure the foot is facing away from the center of the
drone. Tilt the EXOLANDER©Half as shown.
3. Install the other EXOLANDER©Half in the open Saddle Snap Lock
locations. Bring the units together and align the Pin into the Hole on
each side.
4. Align Locking Knob & Screw and Thread Locking Nut Insert on each
side.

7
5. Tighten each screw until the units are mated.
6. The EXOLANDER©installation is now complete.
7. To install the Landing Skid, align each Tab on Landing Skid with each
Slot on the EXOLANDER©Landing Foot. Press and snap Landing Skid
on.
WARNING:
Manually test the EXOLANDER©Landing System by wiggling it and making
sure nothing is loose. Note that a small amount of movement between the
structure and the UAV has been created, at the request of AUTEL, to
eliminate adding unnecessary forces to the vehicle’s structure.

8
D100 DRONE SPOTLIGHT©
REFERENCE GUIDE
Power/Mode Switch
¼-20 Threaded Hole
(2 ea)
Mounting Knob (2 ea)
D100 Drone Spotlight©
Back View
Battery Cover

9
WHAT'S INCLUDED
D100 Drone Spotlight©
Mounting Knob (2 ea)
18650 Lithium-Ion Battery (2 ea)
XTAR Battery Charger
PHYSICAL CHARACTERISTICS
DIMENSIONS
3.46 x 2.03 x 2.46 in (88 x 51.5 x 62.5 mm)
WEIGHT
8.92 oz (253 g)
12.23 oz (346.6 g) with provided 18650 batteries
WARNINGS
Please fully charge the provided 18650 batteries before using the D100©for the
first time.
Do not stare into the LEDs for long periods of time or from close range (less than
2 ft / 0.6 m)
While using any FoxFury product, please operate at safe speeds.
It is the responsibility of drone/UAV users to follow the FAA and global laws and
regulations
and/or the laws and regulations applicable to the flight location.
The D100©will become hot to touch after 20 min of continuous use. Please handle
carefully by avoiding contact with the metal heatsink.

10
BATTERY
D100©requires two (2) 18650 batteries.
Mixing of new and used, or different brand batteries, is not
recommended as this could lead to leakage or explosion.
BATTERY INSTALLATION AND REPLACEMENT
❶Slide the battery cover open and insert the battery according to the plus
(+) and minus (-) symbol located inside of the battery compartment.
❷Once batteries are installed, test the light’s performance by activating the
Power/Mode Switch. Slide the battery cover back on.
CHARGING BATTERY
Refer to the instruction manual provided with the XTAR Battery Charger.
OPERATIONAL MODES
OPERATIONAL MODES
Press and hold Power/Mode Button to turn the light ON.
Press Power/Mode Button again to change the mode to STROBE.
Press Power/Mode Button again to turn the light OFF.
MODE
LUMENS
BATTERY LIFE
ON
2,300
70 minutes
TURBO-
STROBE
2,300
140 minutes
Power/Mode
Switch