Foxpro JackDaddy User manual

2
Important Information
FOXPRO
®
’s goal is to provide our customers with the highest quality products in the
industry. We take great pride in manu acturing our products in the USA. Please do not
hesitate to contact us or assistance, comments or questions.
FOXPRO
®
Inc.
14 Fox Hollow Drive
Lewistown, PA 17044
[phone]
Fax: [phone]
Hours of Operation
Monday – Friday
8AM – 5PM EST
Contact Us
Customer Service: [phone]
Toll Free Orders Only: 866-463-6977
eneral Inquiry E-mail: sales@go oxpro.com
This manual, the animal sounds stored in your caller, and animal sounds purchased from
FOXPRO® Inc. for installation in your caller are protected by copyright.
Copyright ©℗ 2014 by FOXPRO
®
Inc.
REV6 - Publication Date: September 16, 2014

3
FOXPRO Jack Daddy Operation Instructions
To avoid personal injury and prevent product damage, read all operating instructions and sa ety
precautions prior to use. A copy o these instructions can be ound online at the ollowing
address: http://www.go oxpro.com/manuals/jackdaddy.pd Please note that these instructions
may be updated without notice. It’s recommended to periodically check the instructions to be
aware o any changes.
Jack Daddy Requirements
The Jack Daddy is shipped without batteries. The Jack Daddy requires 4 ‘AA’ batteries. We
recommend the use o high-quality rechargeable NiMH batteries or the best overall
per ormance.
Installing batteries in the Jack Daddy
1. Access the battery compartment by removing the door on the back o the Jack Daddy.
The door eatures a knurled thumbscrew or easy access.
2. A ter the door has been removed, locate the black plastic battery tray. The tray is
double-sided, providing spaces or 4 ‘AA’ batteries.
3. Remove the battery tray rom the compartment.
4. Insert the batteries into each battery cavity while observing polarity as indicated.
5. Place the battery tray back into the compartment
6. Secure the door back to the Jack Daddy.
Jack Daddy Remote: Requirements
The Jack Daddy Remote contains a single lithium coin cell battery (CR2032). To replace the
battery, ollow the instructions below:
WARNIN
Before attempting to replace the battery, it is crucial that you understand the risks
of electrostatic discharge potentially harming the electronic board during battery
replacement! Prior to replacing the battery, make sure that you are static ree. You
can touch your hand to a re rigerator door, oven housing, door knob, etc. I you have
the ability to use a proper grounding wrist strap, please do so.
1. Care ully separate the Jack Daddy Remote into two halves. This can be accomplished
with a lathead screwdriver or other comparable tool.
2. Locate the battery and care ully remove it rom the board by sliding it out o the
holder. Note battery orientation as you remove it as the new battery must go back
in the same way.
3. Care ully slide the new battery into the holder.

4
4. Place the circuit board back inside the appropriate case hal .
5. Line the two halves up together and snap them shut to orm a single device once
again.
Setting Up the Jack Daddy
The ollowing instructions apply whether you are using the Jack Daddy as a standalone device or
in conjunction with a FOXPRO digital game call.
Basic Field Deployment Instructions
1. Locate the mounting stake on the le t side o the housing. The Jack Daddy sits upon
this stake while in use.
2. Unscrew the mounting stake rom the le t side housing.
3. Screw the stake into the mounting point on the bottom o the Jack Daddy.
4. Locate the decoy topper support rod on the right side o the housing. The rod is
removed by pulling it straight up. Note: there is a plastic decoy support rod alignment
piece that holds the rod in place. You may need to ree this piece prior to pulling out
the rod.
5. Place the bird on the top o the rod by sliding it down and over the tip.
6. Secure the bottom o the rod to the Jack Daddy by inserting it into the receptacle on
the top o the Jack Daddy and snapping the plastic decoy support rod alignment piece
in place at the base.
7. Remove the Jack Daddy Remote rom the back o the Jack Daddy by pulling it straight
out o its compartment.
Powering On the Jack Daddy
1. Locate the power switch on the ront o the Jack Daddy. Notice that it has 3 positions.
From le t to right: On, Off, On w/ LED. The di erence between “On” and “On w/ LED”
is that “On w/ LED” results in the LED illuminating when powered on.
2. Slide the switch into the desired position to turn on the power. I you selected “On w/
LED” you will notice the LED illuminate.
Toggling Decoy Motion
1. Make sure the Jack Daddy is powered on.
2. The Jack Daddy Remote eatures two buttons. The bottom button is or toggling the
decoy motion on and o .
3. To activate decoy motion: push the bottom button a single time. To deactivate: push
the button a second time.
Playing a Sound
1. Make sure the Jack Daddy is powered on.

5
2. To the right o the power switch is the sound selector switch. This switch has three
positions labeled 1, 2, and 3. Each position represents a single sound. Sound 1 is a
FOXPRO Sound “L54 Bay Bee Cottontail”. Sound 2 is a FOXPRO Sound “R07 Vole
Squeaks”. Sound 3 is FOXPRO Sound “B04 Worried Woodpecker”. Move the switch
into the desired position.
3. The Jack Daddy Remote eatures two buttons. The top button is or toggling the
sound on and o .
4. To play the selected sound: push the top button a single time. To stop playing the
sound: push the button a second time.
5. To change the sound, move the sound selector switch to one o the other positions.
You cannot change the sound rom the remote control.
Connecting to a FOXPRO ame Call
You can connect the Jack Daddy to an existing FOXPRO game call to use it strictly as a decoy.
When connecting it to a FOXPRO game call, the Jack Daddy will not produce any sound.
1. Connect a 3.5 mm stereo cable rom the jack on the Jack Daddy to the auxiliary jack
on your FOXPRO game call.
2. Power on the Jack Daddy to your desired state (with or without LED).
3. Turn on your FOXPRO game call.
4. Use the AUX button on your FOXPRO game call remote to toggle the Jack Daddy
decoy motion on and o .
Maximizing Remote Range
The Jack Daddy is capable o reaching operational remote control range o at least 100 yards. I
you experience inadequate remote control range, please be sure to ollow these guidelines:
•Always maintain line o sight between the remote control and the Jack Daddy.
•Always use strong batteries in the Jack Daddy and Jack Daddy remote control.
•Hold the remote control approximately 12 inches away rom your body. Holding the
remote closer will result in less range. Compare Figure 1 and Figure 2 on the next page
or re erence.
•Do not operate in areas with overhead power lines.
•Orient the remote control as shown in Figure 3 (image on next page) to achieve the
best overall range. Holding the remote control as shown in Figure 4 (image on next
page) can result in shorter range.

6
Figure 1 – Average Range
Figure 2 – Maximum Range
Figure 3 – Proper Orientation
Figure 4 – Improper Orientation

7
FCC Information
NOTE: This equipment has been tested and ound to comply with the limits or a Class B digital
device, pursuant to Part 15 o the FCC Rules. These limits are designed to provide reasonable
protection against harm ul inter erence in a residential installation. This equipment generates,
uses, and can radiate radio requency energy and, i not installed and used in accordance with
the instructions, may cause harm ul inter erence to radio communications. However, there is
no guarantee that the inter erence will not occur in a particular installation. I this equipment
does cause harm ul inter erence to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to correct the inter erence by one or
more o the ollowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet or circuit di erent that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician or help.
Operation is subject to the ollowing two conditions: (1) this device may not cause harm ul
inter erence, and (2) this device must accept any inter erence received, including inter erence
that may cause undesired operation o this device. Modi ications not expressly approved by the
manu acturer could void the user’s authority to operate the equipment under FCC rules.
Industry Canada Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the ollowing two conditions: (1) this device may not cause inter erence, and (2) this device
must accept any inter erence, including inter erence that may cause undesirable operation o
the device.
Le présent appareil est con orme aux CNR d’Industrie Canada applicable aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouilage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le unctionnement.
Warranty Statement
Your FOXPRO® Jack Daddy is warranted to be ree rom de ects in materials and workmanship
that diminish its use ulness or a period o one year rom the date o purchase i the item was
purchased rom a FOXPRO Authorized Retailer. Return the unit prepaid and packaged securely
along with proo o purchase to FOXPRO. Include a note describing the de ect or problem. This
limited warranty is void i the unit is physically damaged, used in a manner contrary to intended
use, or otherwise abused, either intentionally or unintentionally. Also speci ically excluded are
batteries and water damage.