Foxun SX-MX88-3DCAT User manual

Quick Start Guide
Features
•Any eight Sources to Any eight Displays,Each port supports HDMI or DVI inputs.
•Transmission distance up to 50m under 1080P@60Hz over Single Cat5e or Cat6 cable.
•Transmission distance up to 30m under 1080P@60Hz over double Cat5e or Cat6 cable.
•The HDMI input is compensated, clock/phase adjusted and jitter free so all the user sees is
a high quality HDMI signal.
•Independent switch able EDID function for choosing which resolution to display.
•Support high denition resolutions 1080p, 1080i, 720p and other standard video formats.
•Supports LPCM 7.1 channel output from each of the independent HDMI ports.
•Switching modes: panel buttons, local IR, RS232 and Smart phone.
•Support HDCP .
•1U'srack design for easy installation.
•Support 3D.
•With WIFI .
HDMI Matrix 8x8 built-in WiFi
SX-MX88-3DCAT
1

Packing contents
1) Main Unit: 8x8 HDMI Matrix
2) Power supply DC 12V 4A
3) Remote Controller
4) IR-RX cable x 1PCS
5) M3x5 Screw x 8PCS
6) Operating Instructions
7) Mounting ear
8) RS232 cable
Dimensional drawing
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Specications
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
280mm
463.5mm
436.5mm
42.5
2

-5 to +35 C(+23 to +95
5 to 90%RH (No Condensation)
110-240V/ 12VDC power supply
24Watts
Cold-Rolled (Cold Rolled) Steel
W436.5xH280xT42.5mm
3800g
1080P 30m over Dual Cat5e/6 cable
1080P 50m over single Cat5e/6 cable
HDMI receptacle.
Power connector terminal
Power DC receptacle
IR Extender
RJ45 receptacle
Up to 1080p@60Hz@24 b/pixels, support 3D
225MHz/6.75Gbps
Front Panel
This monitor displays your settings information with each output and input selection
IR windows:: infrared sensor to receive any IR commands from the IR remote control.
OUT 1~8 & IN 1~8: Press the output source selection button in order to choose which
input port corresponds to the desired output port. First select your output port from 1-8,
wait 1 sec, then choose the desired input port from ports 1-8. Each output selection
only allows a single input setting each time.
1
2
3
5
7
6
3

Rear Panel
ALL: Press this button to set all the outputs to display with the same input. frist pressing
the “All”button then press an input number to confirm the selection.
D/S: Press this button to Double LAN cable mode and press it again to single LAN cable mode.
WIFI: This slot is used to install the antenna.
Assembly ear
4
5
6
7
RS232 port :For HDMI Matrix control on PC.
RS232 port :For WIFI module setup.
HDMI input ports(HDMI or DVI) .
RJ45 ports:.Video outputs
RJ45 ports:.DDC outputs
POWER: Press this button to turn the system on.
IR extender : This slot is where you can extend your IR receiver with an IR extender
cable that supports only 38KHz.
Power input : Plug the 12V DC power supply into the unit and connect the adaptor to
an AC wall outlet.
1
2
3
4
5
6
7
8
Connecting and operating
1) Connect the HDMI input sources into 8x8 HDMI Matrix and note the input chosen.
2) Connect RJ45 OUT of HDMI matrix
Connect HDMI OUT of HDMI receiver to display equipment.
3) Connect IR-RX cable into IR-RX Ext port on the receiver and afx the IR receiver in direct line
of site with the handheld remote control.It is recommended to afx the receiver on the display
frame /bezel or the display stand.
Note：Do not affix the emitter until the placement is tested.
4) Power up all units, the matrix,Receiver, sources and displays.
5) Use remote or select the button on the front panel to choose the desired input source.
1
3 4 7
265
8
4

1. Front panel control
The HDMI matrix front panel control switching inputs to the various outputs. There are
four groups of LEDs for each output port. The LED lit on the position means that the output
port selects this input as its source.
3. IR extender control
User can use the IR receiver cable to change the IR receiver
position.
If controlling the HDMI matrix through the 1/8” (3.5 mm) input
jack on the rear panel, connect the IR cable directly to the
matrix rear IR Ext socket.
4. RS232 remote control.
1. The Message Window
2. Local IR remote control
User can control the HDMI route of the matrix by using the
IR remote. There are two group key pads for sixteen ports.
Press the output source selection button in order to choose
which input port corresponds to the desired output port.
(For example:Output 8 select Input7 source,rst Press
out 8,then press in 7,LCD will display “8-7”)
Operation
1-1
5-5
2-2
6-6
3-3
7-7
4-4
8-8 D
D/S
5

2.1 Receive Window
The “receive window” will show the message
received from matrix. When you click the Control
Buttons (see step 4) or send Control Command
(see 2.3) to matrix, it will send out the message
about “operation results” as right:
2.2 Status Button
Click this button to read the status of Matrix.
The status is about which input is selected by the
output.
2.3 Send Window
Input the control command in this window.
The control command use ASCII.
3 The Com Status
3.1 connect state.
Connect state shows the com connected or not. If it is connected, the state is green. Otherwise,
the state is red.
3.2 com select.
Select which com you will use.
Connect button.
The word on this button will change when the connection state changes. If the word is “Disconnect”,
then click this button, the com will be closed. If the word is “Connect”, then click this button, the com
will be opened.
3.3 Com port setting:
Baud Rate: 9600 bps
Data bits: 8 bits
Parity: None
Stop bits: 1 bit
Flow control: None
6

4 Setting Button
Click this button to enter
Setting menu. If the signal
is not stable, please turn on
the HDMI long cable mode.
4.1 EDID Set button
Select the Output Port in “Port Select” column, click “Read EDID” button to get EDID from display
equipment.
Select the Input Port in “Port Select” column, click “Download” button to set EDID of this Input
Port the same as display equipment.
Click “Save as” button to save EDID read from display equipment as “*.bin” le.
Click “Open EDID” button to open saved “*.bin” le, select the Input Port in “Port Select” column,
click “Download” button to set EDID of this Input Port the same as “*.bin” le.
7

5.Android OS control
5.1 Install android apk(Matrix88.apk)
5.2 Connect device
Set the Wi in your phone/ pad, run “matrix 88” , input equipment Wi module’s IP address
(10.10.100.254), then click “connect” to enter.
Main menu
8

6.IOS control
6.1 Go to “App store ”， search “Matrix88” ,download and install the APP.
6.2 Connect device
Set the Wi in your iPhone/iPad ,run “Matrix88”, input equipment WIFI module’s IP address
(10.10.100.254) ,then click “Button” to enter.
Main menu
9

RS-232 pin assignment
HDMI Matrix
PIN
Assignment
1
NC
2
TX
3
RX
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
Remote Control Console
PIN Assignment
1 NC
2 RX
3 TX
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
10