FS.COM FS018 User manual
Wireless AP/Router
Quick Installation Guide
FS018 V1.0
January 2017
Installation Diagram
1
POE POWER SUPPLY
AP
……
…………
AP AP AP AP
Solution 1 Solution 2
Installation
2
2.1 Ceiling-mounted Installation
Ceiling Ceiling
Note:Solution 1 (Single Device Setting): Get into the web setting page independently.
Solution 2 (Multiple Devices Setting): Do centralized management settings and
local portal by AC core gateway. (POE power supply and other devices are not
standard, please refer to the packing list. )
①Remove the chassis of
the AP, and fix it on the
ceiling by screws.
②Connect the LAN port
of the device by cable. (If
there are multiple
devices, please connect
the WAN port of the
device by cable for
centralized management.)
Internet Internet
AC CORE GATEWAY
CORE SWITCH
POE SWITCH POE SWITCH
③Fix chassis on the AP
appropriately.
3Single Device Configuration
3.1 Connection Diagram
POE Power Supply
(Not Standard)
Higher Level Network
Note: This quick installation guide is taken the circled ceiling AP for an example.
Some of square ceiling AP have 4 screws and please push one side to install.
Note: Set the LAN port of the device to the computer.
2.2 Wall-mounted Installation
wall
wall
①Remove the chassis of
the AP, and fix it on the
ceiling by screws.
②Connect the LAN port
of the device by cable. (If
there are multiple devices,
please connect the WAN
port of the device by cable
for centralized manage-
ment.)
③Fix chassis on the AP
appropriately.
3.2 Set the computer to obtain the IP address automatically, and
connect the LAN port of the device to the device management
interface.
简体中文
login
LAN2LAN1
AP Bridge Router
SWITCH MODEM
Wizard
System
Firewall
Network
3.3 Open the computer browser, and input 192.168.10.1 to get
into the device login page. The device is defaulted as Router
Mode. When you login at the first time, you need to set a
password. The device language has Chinese and English to be
chosen, and you can set up the language by the top right corner
icon .
3.4 When you get into the setting page, there are three working
modes in the Wizard: PPPOE, Static IP and Dynamic IP.
Language
Settings
English
Please enter password
status information
English Logout
12
Lan Settings WiFi 2.4G finish
Lan Settings
IP address
Subnet mask
Next
192.168.10.1
255.255.255.0
English Logout
Users
status information
Wizard
System
Firewall
Network
2.4G wireless
Advanced setting
Prev Next
Enter or 8-32 Characters
1 2
Lan Settings WiFi 2.4G finish
SSID
Password
Bandwidth
Country
Channel
20MHz
China
auto
Users
status information
Wizard
System
Firewall
Network
English Logout
FS.COM
3.5 Click AP mode and set up IP Address and Subnet Mask. The
IP address and Subnet mask should be within same network
segment as upper network and can’t be conflict with IP address
from upper network router. After setting, you can visit the device
from the IP address that you have set just now by connecting
internet with WAN port of the device.
Notes: ①In AP mode, the IP address from the other devices connected to the AP will
be allocated by the upper network router.
②According to the defaulted setting, there is no need to change IP address. If you
want to manage the device, just manually set IP address in the computer.
3.6 AP Mode: You can set up wireless SSID, password and
channel in advanced settings. After setting, other mobile devices
can connect the device SSID to surf the internet.
Next
WiFi 2.4G finish
Bridge
settings Wireless
settings
12
Lan Settings
3 4
Lan Settings
IP address
Subnet mask
192.168.10.1
255.255.255.0
status information
Wizard
System
Firewall
Network
English Logout
AP
IP address
Subnet mask
2.4G SSID
Prev finish
192.168.10.1
255.255.255.0
1 2
Lan Settings WiFi 2.4G finish
Users
status information
Wizard
System
Firewall
Network
English Logout
FS.COM
Scan Results
BSSID
40:A5:EF:84:E6:34
40:A5:EF:84:DE:64
40:A5:EF:85:48:21
00:E0:4C:81:96:D1
40:A5:EF:84:E6:31
40:A5:EF:84:DE:61
40:A5:EF:80:97:36
unknown 1
1
2
2
1
1
2
unknown
unknown
SSID Channel Operation
Refresh
NO.
1
2
3
4
5
6
7
unknown
unknown
FS.COM
3.7 Bridge Mode: Please ensure that WDS in the upper network
is enabled. AP device can set up intranet segment, and then
select the wireless SSID signal you need to bridge and input
wireless password. The password is the same as your upper
network router.
FS.COM
status information
Wizard
System
Firewall
Network
English Logout
Prev Next
WiFi 2.4G finish
Bridge
settings Wireless
settings
1 2
Lan Settings
34
Wireless settings
IP address
Subnet mask
Gateway
DNS
automate
Static DHCP
automate
automate
automate
e.g: xxx.xxx.xxx.xxx
e.g: xxx.xxx.xxx.xxx
e.g:192.168.10.1
e.g:202.96.134.133
status information
Wizard
System
Firewall
Network
English Logout
Prev Next
WiFi 2.4G finish
Bridge
settings Wireless
settings
1 2
Lan Settings
34
IP address
Subnet mask
Gateway
DNS
Static DHCP
Wireless settings
Bridge settings
Scan Bind
SSID
Password
2.4GHz
scan
status information
Wizard
System
Firewall
Network
English Logout
Prev Next
WiFi 2.4G finish
Bridge
settings Wireless
settings
1 2
Lan Settings
3 4
Enter or 8-32 Characters
FS.COM
①Select “DHCP” and the device will automatically receive IP
address segment from the upper network.
② Select “Static” and you need to manually input IP address and
ensure that the segment should be the same as the upper
network. (IP address can not be conflict with the upper network
device.)
③ Set up SSID and password for this device and click “Next” to
finish settings.
LAN2LAN1
AP
SWITCH MODEM
status information
Wizard
System
Firewall
Network
English Logout
Bridge Router
IP address
Subnet mask
STA SSID
2.4G SSID
192.168.10.1
255.255.255.0
status information
Wizard
System
Firewall
Network
English Logout
Prev finish
WiFi 2.4G finish
Bridge
settings Wireless
settings
1 2
Lan Settings
3 4
Bridge settings
FS.COM
FS.COM1
2.4G Wireless
SSID
Password
status information
Wizard
System
Firewall
Network
English Logout
Prev Next
WiFi 2.4G finish
Bridge
settings Wireless
settings
1 2
Lan Settings
3 4
FS.COM
FS.COM
3.8 Router Mode: There are three ways to surf the internet which
are PPPOE, Static and DHCP.
① PPPOE: It needs to fill in the account number and password,
which are provided by ISP.
Wireless settings
User
Password
MTU
Service name
Next
Max Length 63 characters
Max Length 63 characters
1492
Max Length 63 characters
PPPoE
WiFi 2.4G finish
Lan Settings
12
Wireless settings
3
status information
Wizard
System
Firewall
Network
English Logout
Static DHCP
Lan Settings
IP address
Subnet mask
192.168.10.1
255.255.255.0
status information
Wizard
System
Firewall
Network
English Logout
Prev Next
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
Router
192.168.10.1
255.255.255.0
status information
Wizard
System
Firewall
Network
English Logout
Prev finish
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
IP address
Subnet mask
2.4G SSID FS.COM
2.4G Wireless
SSID
Password
advanced setting
Bandwidth
Country
Channel
20MHz
China
auto
status information
Wizard
System
Firewall
Network
English Logout
Prev Next
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
FS.COM
FS.COM
Next
PPPoE
e.g: xxx.xxx.xxx.xxx
e.g: xxx.xxx.xxx.xxx
e.g:192.168.10.1
e.g:202.96.134.133
Lan Settings
IP address
Subnet mask
192.168.10.1
255.255.255.0
192.168.10.1
255.255.255.0
status information
Wizard
System
Firewall
Network
status information
Wizard
System
Firewall
Network
status information
Wizard
System
Firewall
Network
status information
Wizard
System
Firewall
Network
English Logout
English Logout
English Logout
English Logout
Prev Next
Prev Next
Prev finish
Static DHCP
IP address
Subnet mask
Gateway
DNS
Wireless settings
WiFi 2.4G finish
Lan Settings
12
Wireless settings
3
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
2.4G Wireless
advanced setting
Bandwidth
Country
Channel
20MHz
China
auto
SSID
Password
IP address
Subnet mask
2.4G SSID
Router
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
FS.COM
FS.COM
FS.COM
② Static: It needs to fill in IP address, Subnet Mask, Gateway and
DNS, which are provided by ISP.
192.168.10.1
255.255.255.0
192.168.10.1
255.255.255.0
status information
Wizard
System
Firewall
Network
status information
Wizard
System
Firewall
Network
status information
Wizard
System
Firewall
Network
status information
Wizard
System
Firewall
Network
English Logout
English Logout
English Logout
English Logout
Next
Prev Next
Prev Next
Prev finish
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
IP address
Subnet mask
Gateway
DNS
PPPoE Static DHCP
automate
automate
automate
automate
Wireless settings
Lan Settings
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
IP address
Subnet mask
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
2.4G Wireless
advanced setting
SSID
Password
Bandwidth
Country
Channel
20MHz
China
auto
WiFi 2.4G finish
Lan Settings
1 2
Wireless settings
3
Router
IP address
Subnet mask
2.4G SSID
FS.COM
FS.COM
FS.COM
③ DHCP: It needs to be allocated IP by the upper network device
then you can surf the internet.
Copyright Statement
No part of this manual shall be copied, reproduced, transcribed or
translated in any form or by any means without the prior written
consent of FS.COM. Product specifications and information
mentioned in this manual are for reference. Any updated information
shall not be announced. Copyright© 2009-2016 FS.COM. All Rights
Reserved. All statements and information are not constitute any form
of guarantee. FS trademark and FS logo belong to FS.COM.
Table of contents
