FUFU & GAGA KF200066 User manual

Changing Table
Version:08/10/2022 1/22

please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
2/22

When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
3/22
A x 52 B x 52
6 x 35 mm
6 x 50 mm
12 x 4 mm 4 x 14 mm
C x 24 D x 40
15 x 9 mm
4 x 30 mm
350 mm 350 mm 350 mm 350 mm
6 x 30 mm
6 x 30 mm
3 x 12 mm
3 x 14mm
4 x 35 mm
3.5 x 12 mm
E x 35
P x 1
Nx 1M x 2
CL x 5CR x 5DL x 5 DR x 5
Q x 2 R x 8
F x 9 J x 16H x 16 K x 1G x 9
L x 1

4/22
X2
X2
1
2
4
4
5
6
6
7
8
9
3
17
16 20
22
24
21
21
32
31
16
17
30
30
23
25
18
19
11
14
13
15
10
28
29 27
11
11

11
5/22
350 mm350 mm
2
6 x 35 mm
A x 11
3 x 12 mm
D x 10 CL x 4 CR x 1
CL
D
D
D
D
CL
CL
CL
D
D
D
D
D
D
1
1
3
3
CR
A
A
AA
A
A
A
A
A
A
A
A
Insert quickfit screw(A) into No.1 and No.3
Fix slide rail(CL) and (CR) to No.1 and No.3
plates respectively with screw(D) as shown.
Please pay attention to the holes where the
accessories are inserted.
plates with a screwdriver as shown.

3
6/22
350 mm 350 mm
4
6 x 35 mm
A x 10
2
CL
3 x 12 mm
D x 10 CL x 1 CR x 4
22
22
D
D
D
D
D
D
D
DCR
CR
CR
CR
CL
D
D
D
CL
CR
D
A
A
A
AA
A
A
A
A
A
A
9
Fix slide rail(CL) to No.2 plate with screw(D) as shown.
Fix slide rail(CR) to another side of No.2 plate with screw(D).
Please pay attention to the holes where the accessories are
inserted.
Insert quickfit screw(A) into both sides of
No.2 and No.9 plates with a screwdriver
as shown.

5
7/22
15 x 9 mm
B x 6
6 x 30 mm
C x 4 L x 1
IIIIII
6 x 50 mm
4
4
5
9
2
L
C
C
C
C
C
B
B
B
B
B
B
B
2
4
Attach two No.4 plates to No.2 with
short wooden dowel(C) and turn cam
lock(B) clockwise to tighten as shown.
Attach No.5 plate to No.2 with long
wooden dowel(L) and turn cam lock(B)
clockwise to tighten as shown.
Attach No.9 plate to No.2 and turn cam
lock(B) clockwise to tighten as shown.

6
8/22
15 x 9 mm
Bx6
6 x 30 mm
Cx6
IIIIII
9
2
3
3
CC
CC
C
B
B
9
Attach No.3 plate to No.4,5,9 plates
with short wooden dowel(C) and turn
cam lock(B) clockwise to tighten as
shown.

7
9/22
IIIIII
15 x 9 mm
B x 4
6 x 30 mm
C x 3
6
6
8
7
B
B
L
C
C
C
B
B
B
7
Attach two No.6 and No.8 plates to
No.2 with short wooden dowel(C) and
turn cam lock(B) clockwise to tighten
as shown.
Attach No.7 plate to No.2 and turn
cam lock(B) clockwise to tighten as
shown.

8
10/22
11
11
Slide No.11 plate into available slots as shown.

9
11/22
IIIIII
15 x 9 mm
Bx5
6 x 30 mm
Cx5
1
C
C
C
C
C
C
B
B
B
B
B
B
Attach No.1 plate to No.6,7,8,9
plates with short wooden dowel(C)
and turn cam lock(B) clockwise to
tighten as shown.

10
12/22
6 x 35 mm
A x 6
11
10
A
A
A
A
A
A
A
28
Slide No.10 and No.11 plate into available
slots as shown.
Insert quickfit screw(A) into No.28 plate with
a screwdriver as shown.

11
12
13/22
6 x 35 mm
A x 1
15 x 9 mm
Bx1
4 x 35 mm
Ex2
4 x 35 mm
Ex8
29
27
27
13
13
15
29
14
E
E
E
B
B
E
29
13
13
A
A13
27
E
EE
E
E
E
E
E
E
E
15
13
Insert quickfit screw(A) into No.13 plate
with a screwdriver as shown.
Attach No.27 plate to No.29 plate with
screw(E).
Then attach
No.13 plate
to No.27
plate, turn
cam lock(B)
clockwise to
tighten
as shown.
Connect No.14 and No.15 with No.13,29
plates using screw(E) as shown.

13
14/22
IIIIII
15 x 9 mm
Bx6
6 x 30 mm
Cx6
28
11
C
B
B
B
B
B
B
C
CC
B
C
Cover No.28 plate to No.1,2,3 plates
with wooden dowel(C) and turn cam
lock(B) clockwise to tighten as shown.

14
15/22
Qx2
3.5 x 12 mm
Rx8
29
Q
Q
Rx4
R
RR
R
Rx4 Q
Attach No.29 plate to No.28 at first.
Then fix with part(Q) and screw(R) as shown.

15
16/22
6 x 35 mm
A x 24
16
Ex10
3.5 x 12 mm
AA
A
A
AA
A
A
AA
AA
AA
A
A
25
23
24
21
17
16
30
20
X2 X2
X2 X2
E
E
E
E
E
E
E
Insert quickfit screw(A)
into No.20,23,25 plates
with a screwdriver as
shown.
Attach No.16,17,30 plates to No.24 with
screw(E) as shown.
Slide No.21 plate into available slots as
shown.

17
17/22
15 x 9 mm
B x 10 F x 4 G x 4
IIIIII
18
D x 8
3 x 12 mm 350 mm 350 mm
DL x 2 DR x 2
25
X2
X2
B
B
B
F
F
G
G
G
B
B
B
B
D
D
D
D
DR
DL
D
DR
4 x 30 mm
Fix runner(DL) and (DR) to No.16 and No.17
plates respectively with screw(D) as shown.
Please pay attention to the holes where the
Attach No.25 to No.16,17,30 plates
and turn cam lock(B) clockwise to
tighten as shown.
Fix knob(F) to No.25 plate with
screw(G).
accessories are inserted.

19
18/22
IIIIII
15 x 9 mm 4 x 30 mm
B x 10 F x 4 G x 4
4 x 35 mm
E x 10
20
22
21
32
31
30
X2 X2
E
E
E
E
E
E
E
23
X2
B
B
B
F
FF
G
G
G
B
B
B
B
Attach No.30,31,32 plates to No.22 with
screw(E) as shown.
Slide No.21 plate into available slots as
shown.
Attach No.23 to No.30,31,32 plates
and turn cam lock(B) clockwise to
tighten as shown.
Fix knob(F) to No.23 plate with
screw(G).

21
19/22
350 mm 350 mm
22
Ex4
4 x 35 mm
D x 8
3 x 12 mm
DL x 2 DR x 2
24 17
30
E
E
18
16
17
19
X2
D
D
D
D
DR
DL
D
DR
E
E
E
E
E
E
Fix runner(DL) and (DR) to No.31 and
No.32 plates respectively with screw(D)
as shown.
Please pay attention to the holes where
the accessories are inserted.
Attach No.16,17 plates to No.18 with
screw(E) as shown.
Slide No.19 plate into available slots
as shown.

IIIIII
350 mm 350 mm
4 x 30 mm
23
20/22
15 x 9 mm
B x 4 F x 1 G x 1
24
D x 4
3 x 12 mm
DL x 1 DR x 1
20 F
B
B
B
B
G
B
B
D
DR
F
G
D
D
D
D
DR
DL
Fix runner(DL) and (DR) to No.16 and No.17
plates respectively with screw(D) as shown.
Please pay attention to the holes where the
Attach No.20 to No.16,17 plates and
turn cam lock(B) clockwise to tighten
as shown.
Fix knob(F) to No.20 plate with
screw(G).
accessories are inserted.