Little Colorado 58 User manual

Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Toy Storage Chest Assembly Instructions; Stock # 58 - WOOD
• Please inspect the parts for damage during shipping and for any missing items. If you suspect that there may be damage or a shortage, contact us
and we will send replacement parts if needed.
• As soon as components and hardware are unpacked; please remove and recycle all plastic bags from possible contact with children.
• Words in Red represent a component or hardware used in assembly.
• Illustrations are intended to help identify components and hardware and are not drawn to scale.
Revised 08/12
by
D. Dominguez
Please read instructions carefully to
avoid accidental damage to
components during assembly.
Hardware
4- #8 5/8 in.
Wood Screws
12- Joint Connector Bolts
14- #5 5/8 in.
Wood Screws
1- Lid Support
Toy Storage Chest Components
Page 1 of 3
Tools needed for assembly
• Medium size #2 Phillips
Screwdriver
• Supplied Allen Wrench
Front
Back
Side
Side
Bottom
WARNING: ADULT ASSEMBLY REQUIRED
WARNING: Assembly kit contains parts with sharp points.
WARNING: Assembly kit contains parts with sharp edges.
WARNING: Package contains plastic bags that present suffocation risks for children.
WARNING: Assembly kit contains small parts that present choking hazards for children.
12- Barrel
Top
Bottom
Lid

Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Toy Stoprage Chest Assembly Instructions- Continued
Revised 10/10
by
E. Layton
• Now that you have the two sides
fastened to the back; slide the
Bottom panel in the bottom grooves
(The side with the Little Colorado
logo is the top side).
• Insert a Barrel Nut into the Back panel
Barrel Nut hole in relation to the Joint
Connector Bolt previously installed.
• Make sure the longest slot on the head
of the Barrel Nut is perpendicular to
the Joint Connector Bolt.
• Fasten the Side panel and Back panel
together. Start Joint Connector Bolt by hand
and after a few turns begin using the supplied
Allen wrench.
• Make sure Back panel ts inside groove.
Tighten bolt to a snug t. Then unscrew one
full turn to allow adjustment.
• Now, repeat steps 1,2 and 3 for
second hole and to assemble
the other Side panel.
• Starting with a Side panel, insert one Joint
Connector Bolt in Joint Connector Bolt
hole.
• Repeat steps 1, 2 and 3 to attach
Front panel to body.
• With the box sitting at on a hard
surface, tighten all eight bolts.
Bottom Panel
Panel Groove
12 3
456
Page 2 of 3
• Using the existing holes, attach bottom of
Lid Support to inside of Back with 2 #8 screws
• Be careful not to over tighten screws.
• Place Lid on top of the box and line
up existing holes located on outside
of the back panel to holes in hinge.
Attach hinge to back of box using 14
#5 screws.
• Be careful not to over tighten screws.
Lid
Body
Back
Lid Support
Partial view of Back/Front panel
Barrel Nut Holes
Joint Connector
Holes
Side Panel
Top
Bottom
Area of Detail

• Open lid to approximately 85 degrees and hold it
in place. Mount the top part of the Lid Support to
the inside of the lid using 2 #8 screws.
• It is very important that the screws be started in
the indentations or the lid support may not function
properly
•Be careful not to over tighten screws.
Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Toy Storage Chest Assembly Instructions- Continued
Revised 10/10
by
E. Layton
Please Recycle Instructions
• Now that you have completed the assembly,
open and close the lid 10 times to break in the
lid support mechanism.
•The lid should not fall when the Lid Support is
properly installed.
• If the lid does not stay in position when raised,
please call us and we will help you. Until the lid
support is properly installed, do not allow
children to use this product. Please check the
lid support mounting screws periodically to
make sure they remain tight.
78
If you would like your Toy Storage Chest Personalized
with your child’s name. Contact us at 303 964 3212 and
we will take your order and mail you your child’s name
complete with mounting instructions.
If you have any problems, please call us and we will help you 303 964 3212 or email [email protected] 4450 Lipan St.,Denver, CO 80211
Page 3 of 3
Use and Care Instructions
Use and care instructions:
The nish on this product is an environmentally friendly water base acrylic made by Sherwin Williams. It may be cleaned with a furniture polish, lemon oil or a non
abrasive cleaner using a soft cloth. DO NOT USE AMMONIA or products containing ammonia such as Windex glass or multi-surface cleaner. Scuff marks can
usually be removed by using a polishing compound sold at auto parts stores.
Little Colorado, Inc is a family run children’s furniture manufacturer located in Denver. Please check out www.littlecolorado.com to see our other products that are
all made here in America. The safety of your children is our highest concern. We are a GREEN company and hope you will be able to recycle the packaging mate-
rial that we used to ship your product.
If you have a comment or a question please contact us at [email protected]. All of us at Little Colorado hope you and your family will enjoy this product for
many years.
WARNING
Failure to properly install Lid Support
will result in an entrapment hazard.
Lid
Body