10
V815 OPERATING INSTRUCTIONS
Check the appearance of the unit when it is unpacked. Do not use the unit if any damage or deformation is found.
Failure to do so may lead to re, damage or malfunction.
For use in a facility or for a system related to nuclear energy, aerospace, medical, trafc equipment, or mobile
installations, please consult your local distributor.
Operate (or store) MONITOUCH under the conditions indicated in this manual and related manuals. Failure to do so
could cause re, malfunction, physical damage or deterioration.
Understand the following environmental limits for use and storage of MONITOUCH. Otherwise, re or damage to the
unit may result.
- Avoid locations where there is a possibility that water, corrosive gas, ammable gas, solvents, grinding uids or
cutting oil can come into contact with the unit.
- Avoid high temperature, high humidity, and outside weather conditions, such as wind, rain or direct sunlight.
- Avoid locations where excessive dust, salt, and metallic particles are present.
- Avoid installing the unit in a location where vibration or physical shock may be transmitted.
Equipment must be correctly mounted so that the main terminal of MONITOUCH will not be touched inadvertently.
Otherwise, an accident or electric shock may occur.
Tighten the xtures of MONITOUCH with a torque in the specied range. Loose tightening may cause MONITOUCH
to come off, malfunction or be short-circuited.
Check periodically that terminal screws on the power supply terminal block and xtures are rmly tightened.
Loosened screws may result in re or malfunction.
Tighten terminal screws on the power supply terminal block equally with a torque in the specied range. Improper
tightening of screws may result in re, malfunction, or trouble.
MONITOUCH has a glass screen. Do not drop or give physical shock to the unit. Otherwise, the screen may be
damaged.
Connect the cables correctly to the terminals of MONITOUCH in accordance with the specied voltage and wattage.
Over-voltage, over-wattage or incorrect cable connection could cause re, malfunction or damage to the unit.
Be sure to establish a ground of MONITOUCH. Ground FG terminal which must be used for the unit. Otherwise,
electric shock or a re may occur.
Prevent any conductive particles from entering into MONITOUCH. Failure to do so may lead to re, damage or
malfunction.
Do not attempt to repair, disassemble or modify MONITOUCH at your site. Ask Hakko or the designated contractor
for repair. Otherwise, it may cause a malfunction.
Hakko Electronics Co., Ltd. is not responsible for any damages resulting from repair, overhaul or modication of
MONITOUCH that was performed by an unauthorized person.
Do not use a sharp-pointed tool when pressing a touch switch. Doing so may damage the screen.
Only experts are authorized to set up the unit, connect the cables or perform maintenance and inspection.
For MONITOUCH using a lithium battery, handle the battery with care. The combustible materials such as lithium or
organic solvent contained in the battery may generate heat, explode, or catch re, resulting in personal injury or re.
Read related manuals carefully and handle the lithium battery correctly as instructed.
Do not press two or more points on the screen at the same time. If there is a switch between the two pressed points,
it may be activated.
Take safety precautions during such operations as setting change during running, forced output, start, and stop. Any
misoperation may cause unexpected machine motions, resulting in machine accident or damage.
In facilities where a failure of MONITOUCH could lead to accident threatening human life or other serious damage, be
sure that the facilities are equipped with adequate safeguards.
At the time of disposal, MONITOUCH must be treated as industrial waste.
Before touching MONITOUCH, discharge static electricity from your body by touching grounded metal. Excessive
static electricity may cause malfunction or trouble.
Never insert the CF card in the socket of MONITOUCH with the wrong direction. Doing so may destroy the CF card
or the socket of MONITOUCH.
The LED lamp on the CF card interface cover lights up in red during supplying power to the CF card. Never remove
the CF card or turn off the power of MONITOUCH while the LED lamp is lit. Doing so may destroy the data on the CF
card. Check that the LED lamp has gone off before removing the CF card or turning off the power of MONITOUCH.
If a LAN cable is inserted into the MJ1 or MJ2 connector on MONITOUCH, the counterpart device may be damaged.
Check the indication on the unit and insert a cable into the correct position.
Notes on LCD
Tiny spots (dark or luminescent) may appear on the display due to the liquid crystal characteristics.
Please note that this is not a fault or malfunction of MONITOUCH.
