Fujion FH-GS7020 SVSS Manual

FH-GS7030 SVGLFH-GS7020 SVGLFH-GS7030 SVSSFH-GS7020 SVSSBuilt-in Gas Hob

1The safety precautions and recommendations provided in the manual are for your own safety. Please keep this booklet for future reference relating to the operation and maintenance of the gas hobs.This gas hob shall be used for domestic cooking only. Any other usage is strictly prohibited. The manufacturer declines all responsibilities in the event of damages caused by improper, wrong or irrational usage of the gas hob. Read and understand the instructions before installation and operation of the gas hob.1. Important safety precautions and recommendationsa.Unpack the gas hob from the carton box and inspect for physical damage. In case of doubt, do not install / operate the gas hob and contact your supplier for professional advice. b.Never attempt to modify the gas hob. c.This gas hob shall be installed in a well-ventilated room and in compliance with the local regulations. d.After cooking, ensure that the gas control knobs are turned back in the off position. e.This gas hob can be used by children aged from 14 years old and above if they understand the operation of the gas hobs and aware of the hazards due to improper usage. f.Do not touch the parts of the gas hob which is heated by the flame during operation of the gas hob. Note that these parts remain hot for a period after the gas hob is turned off.g.Never leave the gas hob unattended during cooking. h.Never try to extinguish a cooker fire with water. I. I f the gas hob is used for a prolonged period, it may be necessary to provide more ventilation by opening more windows. j. In the event of the burner flame being accidentally extinguished, turn off the burner control knob and do not attempt to re-ignite the burner for at least one minute.Dear customer,Thank you for selecting this Fujioh product.k. When using the hob for the first time,you may smell some odor like buring smell ornotice a small emission of smoke.this is NORMAL and is not toxic.this smell willgo off after few time of usages.

22. Warning symbols for toughened glass gas hobDo not place anything e.g. flame tamer or asbestos mat, between pan and pan support, as serious damage to the appliance may result. Do not remove the pan support and enclose the burner with a wok stand, as this will concentrate and deflect heat onto the hotplate. Do not use large pots or heavy weights that can bendthe pan support or deflect flame onto the hotplate. Locate pan centrally over the burner so that it is stable and does not overhang the appliance. Use only a wok support supplied or recommended by the manufacturer of the appliance.

Table 1 – a) Nozzle (Injector) and burner characteristics for LPG / G30 gas at 30 mbarTable 1 – b) Nozzle (Injector) and burner characteristics for Town gas / G110gas at 10 mbar3. Models and parts of the gas hob
Inner Flame Ultra-rapid
Auxiliary Type of burners inner ring Ø injectors Nominal heat input Outer ring Ø injectors (kW) (mm) (mm) Gas burners A. Burner control knob Type of burners (kW) inner ring Ø injectors Nominal heat input Outer ring Ø injectors (mm) (mm) 0.90 0.50 0.98 C. Heat deflectorD. Ultra-rapid ABCDEF
G
FH-GS7030 SVGL FH-GS7030 SVSSB. Inner Flame Ultra-rapid E. Heat deflector G. Auxiliary Heat deflectorF. Auxiliary
Inner Flame Ultra-rapid 
Ultra-rapid Auxiliary — 0.53 0.48 2.40 1.50 2.80
Inner Flame Ultra-rapid 
Ultra-rapid Auxiliary — 1.45 1.30 Ultra-rapid 4.50 5.00 1.10 3.90 4.10 1.10 ABCDEFH-GS7020 SVGL FH-GS7020 SVSS3

4. How to use the gas hobGas burnersThe gas flow to the burner can be regulated by turning the corresponding control knob to one of the following positions. (see Fig.1)The burner should be set at large flame during the initial phase of the cooking toallow quick boiling of the cooking contents. After boiling then turn the controlknob to small flame for slow warming of food or maintaining boiling conditions.Other flame adjustment can be achieved by positioning the indicator betweenthe large flame and small flame. Never adjust the flame size between the largeflame and Off position.Igniting the burnersThe appliance is equipped with automatic ignition system and flame failure safety device. To ignite the burner, carried out the following steps:a. Press and turn the corresponding control knob anti-clockwise to the large flame position. The gas burner will be ignited.b. At this position, hold down the control knob for 5 seconds to allow the flame to heat up the thermocouple.c. By this time, release the knob and the flame shall be remained lighted up.d. Turn the control knob to achieve the flame as desired.e. If the flame can’t be lighted, turn the control knob clockwise to the off position. Then repeat step a to step c.f. After finished cooking, turn the control knob clockwise to the off position.OFF (close valve)High (maximum aperture or flow)Low (minimum aperture or flow)The size of flame depends on the position of the related burner control knob-Burner ON, large flame -Burner ON, small flame (saving mode) -Burner OFF Fig.1 bca4

Battery IgnitionThe automatic ignition system is powered by a 1.5 V battery. If the automaticignition does not work, check the battery compartment under the gas hobto ensure that the battery is positioned correctly. Replace the battery if necessary (see Fig.8).In the event, the automatic ignition fail to operate, ignite the burner with amatch or gas lighter. Selection of burners and diameters of panOn the control panel, near every knob, there is a diagram indicate which burner is controlled by that knob. Select the burner in according to the diameter of the pan used and the heat input. The recommended burners for the flat bottom pan diameters are as follow:Types of burners (cm) Auxiliary Ultra-rapid It is important that the diameter of the pan be suitable to the heat inputof the burner. During usage, adjustment of the control knob would berequired to ensure that the flame do not extend out from beneath thepan (see Fig.2)Fig.2 Pan diameter 8 to 14 20 to 30.5

1. Thermocouple 2. Spark 3. Inner cap 4. Outer ring cap 5. Large burner cup6. Venturi7. Auxiliary burner cap8. Auxiliary burner cupCorrect use of Ultra-rapid burnerTo use the wok, you need to position the wok directly onto center of the pansupport. Recommended wok top open diameter shall not exceed 36 cm.For gas hobs models without Auxiliary and auxiliary burners, when using the flat bottom pan with diameter less than 12 cm, you need to position the minitrivet (Fig.3) provided onto the pan support. After lighting the burner, adjust the control knob so that the flame length do not extend out from the beneathof the pan so as to prevent overheating the pan handle (see Fig.2).Flame failure safety deviceThis gas hob is equipped with flame failure safety device. In the event, theflame is accidently extinguished, the supply of gas to that burner will be shutoff. Before re-lighting the burner, turn off the burner control knob and donot attempt to re-ignite the burner for at least one minute.Fig.31 AuxiliaryUltra-rapid2 3 4 7 5 6 1 2 8
Inner Flame Ultra-rapid
3 4 2 5 6 1 6

5. Cleaning and maintenanceCleaning and maintenance should be carried out after the appliance has turned cold especially when cleaning burner and the cast iron support. Avoid leaving alkaline or acid substances (lemon juice,vinegar etc.) on the surfaces.Avoid using acid or chlorine-based cleaning products.Caution:Special care should be taken around the underneath of the appliance as this area is not designed or intended to be touched and may contain sharp or rough edges, that may cause injury.For safety,always wear a pair of rubber gloves while cleaning.To extend the life of the cooktop, it is absolutely indispensable that the appliance be cleaned carefully and thoroughly on a frequent basis, keeping in mind the following:. STAINLESS STEEL SURFACES Stainless steel can be stained if it remains in contact with highly calcareous water or aggressive detergent (containing phosphorous) for an extended period of time. Stainless steel parts must be rinsed with water and dried with a soft and clean cloth, it is also recommended to clean up any spills as soon as possible. . PAINTED PARTS AND SILKSCREEN PRINTED SURFACES Clean using an appropriate product. Always dry thoroughly. These parts must be cleaned very carefully to avoid scratching and abrasion. . BURNERS AND PAN SUPPORT These parts can be removed and cleaned with appropriate products. Cleaning the Wok BurnerThe burner cup must always be kept clean. When cleaning the burners, remove the burner caps and use a cotton bud, toothbrush or some other item to clean out any incrustations or dirt from area marked as “H” in Fig.4. This procedure is necessary to ensure the burner functions correctly. Clean the burner caps using needle or toothbrush to remove the dirt and carbon blocking the burner holes.(Fig.5). SURFACE ENAMEL PARTS All of the Enamel parts must be washed only with a sponge and soapy water or with non-abrasive products.Fig.4Fig.5H7

Check that the ignition electrode “S” (Fig.7) is always clean to ensure trouble-free sparking.Check that the probe or thermocouple “T” (Fig.7) is always clean to ensure correct operation of the safety valves. Both the ignition electrode and the thermocouple must be very carefully cleaned.Note: regular use could cause discoloring around the burners due to high flame temperature. GENERAL ADVICE√ When the appliance is not being used, it is advisable to keep the gas regulator or TG supply level closed.√ The gas hob required regular maintenance by qualified technician for its reliable operation. We recommend the gas hob maintenance to be carried out at least once every 18 months.Fig.7TTTSSS8The burner cap A must be entered in their lodgment as shown by the arrow (Fig.6). The burner correctly positioned must rotate. Ultra-rapidFBAAfter cleaning the burners and the caps must be well dried and put back correctly. It is very important to check that the burner cups F,burner cap A and cap B has been correctly positioned (Fig.6)-failure to do so can cause serious problem. Fig.6FBAInner Flame Ultra-rapid

6. Installing the batteryInsert a DC1.5V battery into the battery compartment (see below Fig.8 ) in the cover. This battery is the power supply for the electronic ignition of gas burners.Notes for battery installation or replacement:. Only use a DC1.5Volt battery (size “D”). Check for correct polarity ( label to the side of the battery compartment ).. Do not use Alkaline battery.Important notes:. Remove the battery if the cooker is not going to be used for a long time.. If the battery weak or leaks, replace it immediately.. Avoid touching the leaked liquid and make sure it does not come into contact with clothes or other items.. Clean the battery compartment carefully before installing the new one.. Note: The battery is a potential source of danger for children. Keep them away.. Dispose the flat batteries properly. Fig.8
SIZE D
9