FULGOR M6 Manual

M6
Digital audio matrix with DSP
USER AND INSTALLATION GUIDE
V3.0
Software da 3.0.0.4
Firmware da 3.0.0.0

2
Features can be modified without any notice V2020319
PRECAUTION OF USE
WARNING: To reduce the risk of electric shock, do not remove the cover (or rear panel).
Inside, there are no parts that can be repaired by the user; Entrust the repair to qualified personnel.
CAUTION: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.
This symbol, when displayed, indicates the presence of a non-insulated hazardous voltage inside
the body of the device - sufficient voltage to pose a risk of electric shock.
This symbol, when displayed, indicates important operating and maintenance instructions in the
enclosed text. Read the manual.
RECOMMENDATIONS:
All safety and operating instructions must be read before operating the appliance.
Keep the instructions:
Safety and operating instructions must be kept for future reference. This manual is an integral part of the
product and must accompany it in case of any change of ownership. This will allow the new owner to know
the instructions for installation, operation and safety.
Pay attention:
All warnings on the appliance and operating instructions must be followed accurately. Observe all warnings.
Follow the instructions:
All operating and user instructions must be followed.
Notes preceded by the symbol contain important safety information: Read them carefully.
DETAILED SAFETY INSTRUCTIONS.
Water and humidity:
The appliance should not be used close to water (eg near baths, kitchen sinks, near pools, etc.).
Ventilation:
The appliance must be placed in such a way that its location does not interfere with the proper ventilation.
For example, the appliance should not be placed on a bed, sofa cover, or similar surfaces that can block the
ventilation openings or placed in a recessed installation such as a bookcase or cabinet that can prevent the
flow of air, Air through the ventilation openings.
Heat:
The appliance must be located away from heat sources such as radiators, thermostats, clothes dryers, or
other appliances that produce heat.
Power supply:
• The appliance must only be connected to the type of power described in the operating instructions or on
the appliance.
• If the supplied plug does not match the socket, contact an electrician to install an appropriate socket.
Grounding or polarization:
• Precautions should be taken to ensure that grounding and polarization of the device are not affected.
• The metal parts of the equipment are connected to ground via the power cord.
• If the power socket does not have a ground connection, contact a qualified electrician to connect the
grounding device through the terminal.
• For plastic equipment, periodically check the condition of the power supply.

3
Features can be modified without any notice V2020319
Power Cord Protection:
The power supply cord must be installed so that it is not to be trampled or pinched by objects placed on or
against, paying particular attention to wires and plugs that are wall-mounted.
Cleaning:
• When the unit is to be cleaned, dust can be removed using a compressed air jet or damp cloth.
• Do not clean the unit using solvents such as triethylene, paint thinners, fluids, alcohol, high volatility fluids
or other flammable liquids.
Non-use Periods:
The power cord of the appliance must be disconnected from the socket if it is not used for a long time.
Intake of liquids or objects:
Care should be taken to avoid dropping objects and not leaking liquids into the body of the appliance through
the grilles.
Safe use of the power line:
• When disconnecting the appliance, hold the plug and the socket securely.
• When the unit is not used for a prolonged period, stop power by pulling the plug out of the power outlet
• To avoid damaging the power supply line, do not pull the power cord and do not use a twisted cable.
• To avoid damaging the power cord of the apparatus, make sure that it is not being trodden or crushed by
heavy objects.
Moving the unit:
Before each shift, make sure the drive is off. The power cord must be removed from the socket as well as
the unit's connections with other lines.
Do not disassemble the unit:
Do not attempt to disassemble or repair the unit yourself. For any problem that can not be resolved with the
help of this manual, contact a qualified technician or contact our company www.fulgorservice.it
Malfunctions:
For any malfunctions contact our company (www.fulgorservice.it).
IMPORTANT SAFETY RULES:
• Install by following the instructions.
• Never open the equipment: inside there are no user-serviceable parts.
• If you notice a strange smell coming from the appliance, turn it off immediately and disconnect the power
cord.
• Do not obstruct the ventilation grilles of the appliance.
• Avoid working overloading the unit for extended periods of time.
• Do not force commands (buttons, controls, etc.)
• For safety reasons, do not unscrew the plug-in connection. The ground connection is necessary to safeguard
operator safety
• Use only the connectors and accessories specified by the manufacturer.
• The equipment must be kept away from:
 Damp places
 Direct exposure to heat sources (such as sunlight).
Unsuitable ventilation
• In the presence of lightning storms or when the apparatus is not in use, unplug the power plug from the
socket.
• To prevent the risk of fire and electric shock, keep the equipment away from splashes and drops. Above
the apparatus should not be placed vases or other objects containing liquids.
• FULGOR SERVICE s.n.c. Disclaims any liability for incorrect installation of the unit.
GUARANTEES AND RETURN:
The product is equipped with a guarantee of operation and compliance with its specifications, as stated by
the manufacturer. The warranty is 24 months from the date of purchase. Faults detected within the warranty
period, attributable to defective materials or construction defects, must be promptly reported to your dealer
or distributor, enclosing the purchase date documentation and the description of the defect type found.
Failures caused by improper use or tampering are excluded from the warranty. Fulgor Service s.n.c.

4
Features can be modified without any notice V2020319
Establishes by means of return verification the declared defect, related to proper use, and the effective
validity of the guarantee; It then provides for the replacement or repair of the products, but does not however
oblige any compensation for direct or indirect damages resulting from the defect.

5
Features can be modified without any notice V2020319
M644
DAW in real time 6 Input on 4 Out
DESCRIPTION
The M6 digital workstation is equipped with 6 balanced audio input (XLR) fully configurable and
addressable to one or more of the 4 balanced outputs (XLR).
Main electrical characteristics:
 6 balanced inputs with female XLR connectors
 4 balanced output with male XLR connectors
 Maximum input level 8Vpp
 Maximum output level 8Vpp
 Input amplification: from -20dB to +50dB
 Phantom power +24 V can be activated independently on each channel via software
 24 bit analog/digital conversion
 Less than 6w consumption
 20 Digital volume controls (RS485)
 32 Preset selectable and actionable remotely (RS485)
 6 fully configurable remote analog volume controls
 6 fully configurable panel volume controls with precision potentiometers
 RS232 serial line for configuration and setting via PC (Windows)
Main software features:
 Gain control for each input (±50dB)
 Phase control for each input
 Compressor for each input
 Equalization with 3 configurable parametric filters for each input
 6x4 matrix with adjustable attenuations
 Configurable automixer with 5 logical parameters
 NOMA function (total output level attenuation with automatic control according to the
actual inputs open simultaneously)
 Double antilarsen selectable for each output
 1 delay for each output settable from 0 to 64 meters
 Equalization with 6 parametric filters configurable for each output
 Noise-Gate on each output
 Gain control for each output (-60/+6dB)
 Phase control for each output
 Maximum-minimum configuration of the potentiometer that can be associated with one or
more of the inputs or outputs
 Block diagram summary screen of the running configuration
 RS485 enabling/disabling
 Display of inputs and output status (VuMeter) in each window of the work environment
and virtual keys to enable/disable the inputs and outputs (Muting)
 Display of the preset control and accessori functions window (name change, save to disk,
load from disk, set password, default, exit, resources control and save) in each window of
the work environment

6
Features can be modified without any notice V2020319
STATUS LED LED PRESET STATUS
PRECISION POTENTIOMETERS PC INTERFACE
MULTIFUNCTION PORT POWER
BALANCED OUTPUTS
GROUND LIFT
BALANCED INPUTS

7
Features can be modified without any notice V2020319
SOFTWARE
WELCOME WINDOW
From this window it is possible to select the serial port to connect to the matrix, or perform an
off-line configuration, that is, without the device being connected.
MAIN WINDOW
You can access this window or from off-line configuration or by connecting to the device.

8
Features can be modified without any notice V2020319
Detail
This window is always visible in any work environment you are; it is thus possible to check inputs
and output level and enable/disable the muting function.
In the exmaple shown all inputs are open while all the output are in muting condition.
To assign a name to an input or output, right-click on the input or output itself.
Clicking in the tab “Modifica
nome” you can assign one.
Monitor for connection status (ON-LINE o OFF-LINE),
serial, service version (software running on PC),
firmware (of the device) and total DSP resources

9
Features can be modified without any notice V2020319
From this section it is possible to choose and/or save
the presets, select the factory configuration (default)
and save.
☝It is necessary to save frequently in order not
to risk losing the change made; when it is
stored the tab is partially obscured.
From this section it is possible to change the project
name, assign a new password (default ****), save
the project on the computer, upload a project from
the computer or close the work section.
☝When you change the project name it is shown
on the upper left side of the work environment

10
Features can be modified without any notice V2020319
Inputs Tab
For each input it is possible to adjust/select:
Gain by writing the value or pressing the up-down
buttons (min -50 dB max +50dB)
Mute
Phase
24V Phantom power
Managed by automixer
Controlled by a local or remote potentiometer
Activate the dynamics compressor
☝When the automixer is not active, the relevant tab is
partially obscured and therefore CANNOT be
selected.
☝It is possible to control both inputs and outputs with
an internal or external potentiometer and it is also
possible to assign multiple inputs/outputs to a single
potentiometer. It is necessary to calibrate the
potentiometers.
☝When the dynamics compressor is active, the
relevant operation light (triangle near the Th value)
indicated whether the input is open (green) or closed
(red). The wworking range is between -30dB and
+6dB (Th treshold, or operating treshold) with a
compression level (Ratio) variable from 1 (1:1) to 15
(15:1).