FUNAIR SUPER SWEET SLIDE User manual

SUPER SWEET SLIDETM INSTRUCTIONS
1.512.270.4900 | 800.928.4042 | FUNAIR.COM | [e-mail]

FOLLOW THESE INSTRUCTIONS FOR SET UP:
1 Remove the Super Sweet
SlideTM from the product
wrap (FIG. 1). Put wrap aside
for storing Super Sweet
SlideTM later.
2 Unroll the deflated Super
Sweet SlideTM in the area it
will be used (FIG. 2).
3 Straighten it out as much as
possible by unfolding and
opening it (FIG. 3).
4 When the Super Sweet
SlideTM is unfolded, make
sure the FunAir logo is facing
up and the slide is positioned
where it will be used (FIG. 4).
SUPER SWEET SLIDETM INSTRUCTIONS
FIG. 1
FIG. 2
1.512.270.4900 | 800.928.4042 | FUNAIR.COM | [e-mail]
You are about to Inflate the FUN! With proper care, you will receive
years of fun from the FunAir Super Sweet SlideTM.
SET UP
Find an area that is at least 60’ x 12’ that is smooth and free
from debris. Make sure there are no sharp rocks, nails, screws,
sprinkler heads, glass, broken wood, etc. Make sure the area
at the end of the slide is free of pavement, trees and any
other objects that could impede or injure the slider.
INCLUDED IN
THIS PURCHASE:
1 Product Instructions
1 Owner’s Manual
1 Deflated Super
Sweet SlideTM
1 Super Sweet SlideTM
Wrap
1 Set of Plastic Stakes
with Mallet
1 Repair Kit with Glue
1 FunAir Electric Pump
(may be shipped
separately from
inflatable)
IMPROPER USE MAY CAUSE INJURY OR DEATH. READ AND UNDERSTAND
OWNER’S MANUAL AND PRODUCT INSTRUCTIONS BEFORE USE.
WARNING
• Use only on level ground and in grass
areas that are clear of obstacles.
• Never use air compressor to inflate
FunAir products!
• Check and maintain correct air pressure
as indicated adjacent to the inflation
valve(s) or in the Product Instructions
prior to and during use to avoid personal
injury and/or damage to the inflatable.
• Check entire inflatable for leaks or
damage prior to use.
• Wait until previous slider has completed
the slide and exited, before sliding.
• No running on slide.
• Remove all shart objects from your
person before use.
• Somersaults, wrestling, and rough play
are prohibited on the slide.
• No bodyboards or skimboards of any
kind on slide.
• No shoes on slide.
• Wet surface before use.
• Slide surface is slippery: USE CAUTION!
• Do not stand on the inflatable sides.
• Adult supervision is required.
• Seek shelter immediately in bad
weather—DO NOT use slide at that time.
• Do not use under the influence of alcohol
or drugs or while you have any impaired
mental capacity.
• Do not use slide and immediately deflate
if winds exceed 20 MPH (32 KPH).

5 Locate the inflation valves
for slide arms (FIG. 5).
6 Use the inflation adaptor on
the pump hose. Connect the
inflation hose by inserting
the hose into the inflation
valve and twisting 1/4 turn
to the right until it stops,
indicating the hose is locked
in place (FIG. 6).
7 Plug the pump’s electrical
cord into the outlet, connect
the hose to the inflation port
on the side of the pump and
then press the ‘on’ button
(FIG. 7).
8 Inflate each Super Sweet
SlideTM arm until it is 1.0
Pounds Per Square Inch
(PSI). Use a pressue gauge
to measure PSI. The slide
arm will be firm. DO NOT
OVER INFLATE (FIG. 8).
9 Make sure the Super Sweet
SlideTM is positioned with
a minimum of 10’ of soft
landing room at the end
of the slide to ensure safe
exit for sliders. Allow more
room if sliders or conditions
require it (FIG. 9).
10 Use stakes (included),
positioned through straps
on each side of the Super
Sweet SlideTM.
11 When staking the Super
Sweet SlideTM into position,
wrap the straps attached
to the slide around the
stake a few times first.
Then pull them away from
the inflatable until they are
taut, prior to hammering
into the ground.
12 Hammer stakes into the
ground.
13 Wet slide completely and
keep it wet during use
(FIG. 8).
©FUNAIR
1.512.270.4900 | 800.928.4042 | FUNAIR.COM | [e-mail]
FIG. 3
FIG. 4
FIG. 5
FIG. 6
FIG. 7

DEFLATION, PACKING and STORING
1 If possible, let slide sit to dry.
2 Wipe any dirt, water, or
debris off the Super Sweet
SlideTM. Make sure the slide
is completely dry before
storing, to avoid mildew.
3 Prepare the slide for
deflation by opening the
inflation valve on the Super
Sweet SlideTM arms. Remove
the cap from the inflation
valve, push in on the pin and
turn it to the right (FIG. 11).
It will stay open.
4 Connect the pump hose to
the inflation valve on the
slide arm.
5 Connect the hose to the
deflation port on the side of
the pump and turn pump ‘on’
to begin vacuuming air out
of the slide arm. Repeat with
other slide arm.
6 Remove the hose from the
valve and twist the valve
stem back to the left 1/4 turn
to close it.
7 Take one side of the slide
and fold over towards the
other, stopping midway
between the far side of the
FunAir logo and the other
slide arm. Fold the other side
on top of the one just folded,
so that the edges are neat.
8 Starting at the end of the
slide without the inflation
valves, roll the slide tightly.
9 Place the gray webbing strap
provided around the slide
and cinch it down to make
the roll tighter. Then place
the slide into the wrap to
help carry and store.
10 Store in a cool, dry and
rodent free place.
Use of FunAir products is subject to the Terms and Conditions at funair.com/terms, which includes terms that substantially affect your rights,
such as limitations on FunAir’s liability, disclaimers of warranties, and an obligation to arbitrate disputes with FunAir. By purchasing and using
a FunAir product, you are agreeing to be bound by the Terms and Conditions in their entirety. If you do not agree to the Terms and Conditions,
you should not purchase or use the product. All information about the FunAir Limited Warranty is included in the “Agreement”.
SUPER SWEET SLIDETM INSTRUCTIONS
FIG. 8
FIG. 9
FIG. 10
FIG. 11
FUNAIR
GOFUNAIR
FUNAIRFUN
FUNAIRFUN
@GOFUNAIR
©FUNAIR
1.512.270.4900 | 800.928.4042 | FUNAIR.COM | [e-mail]