Gardner Denver Welch WOB-L 2522C-02 User manual

Operation Manual
(EN)
Translation of the german original manual
WOB-L®Piston pumps
Models:
►2522C-02 (230V / 50Hz)
► 2522B-01 (115V / 60Hz)
► 2534C-02 (230V / 50Hz)
► 2534B-01 (115V / 60Hz)
► 2546C-02 (230V / 50Hz)
► 2546B-01 (115V / 60Hz)
2522-34-46
2017-05-16

We are constantly working on the further
development of all our product models.
Reprinting or reproduction of this manual,
including extracts, is not allowed without
the prior written permission of Co. Gardner
Denver ThomasGmbH.
All rights under the copyright laws are
expressly reserved by Co. Gardner Denver
Thomas GmbH.
We reserve the right to make changes and
amendments.
Gardner Denver Thomas GmbH
Am Vogelherd 20
98693 Ilmenau
Germany
T [phone]
F [phone]
[email protected]
www.welchvacuum.com
Customer Support [phone]

Contents
2522-34-46 3
Contents
1Important Information.............................................................................................................4
1.1 General Information..................................................................................................................4
1.2 Target Groups...........................................................................................................................4
1.3 Intended Use.............................................................................................................................4
1.4 Use for an Unauthorized Purpose ............................................................................................4
1.5 Safety Devices..........................................................................................................................5
1.6 Meaning of the Warning notes..................................................................................................5
1.7 Product Standards, Safety Regulations....................................................................................5
2Basic Safety Instructions.......................................................................................................6
2.1 General Information..................................................................................................................6
2.2 Electricity...................................................................................................................................6
2.3 Mechanical Systems.................................................................................................................6
2.4 Hazardous Substances.............................................................................................................7
2.5 High Temperatures ...................................................................................................................7
3Description ..............................................................................................................................8
3.1 Design.......................................................................................................................................8
3.1.1 Connections - Suction-/Pressure side ......................................................................................8
3.1.2 Connecting to the electricity supply ..........................................................................................8
3.1.3 Display - Vacuum- / Pressure Regulator ..................................................................................9
3.2 Additional protection measures against liquids in the pump.....................................................9
3.2.1 Condensate separator (Suction side) .......................................................................................9
3.2.2 Cold trap (Suction side) ............................................................................................................9
3.3 Areas of Application................................................................................................................10
3.4 Materials of the medium-affecting pump parts........................................................................10
3.5 Scope of Delivery....................................................................................................................10
3.6 Accessories.............................................................................................................................10
4Technical Data.......................................................................................................................11
5Installation and Operation....................................................................................................12
5.1 Unpacking...............................................................................................................................12
5.2 Setting up and connecting ......................................................................................................12
5.2.1 Setting up................................................................................................................................12
5.2.2 Connecting..............................................................................................................................12
5.2.2.1 Electrical Connection ..............................................................................................................12
5.2.2.2 Vacuum connection (Suction side) .........................................................................................12
5.2.2.3 Exhaust connection (Pressure side).......................................................................................13
5.3 Operation ................................................................................................................................13
5.3.1 Start-up ...................................................................................................................................13
5.3.2 Decommissioning....................................................................................................................13
5.4 Storage....................................................................................................................................14
5.5 Scrap Disposal........................................................................................................................14
6Maintenance and Servicing..................................................................................................15
6.1 Maintenance Performed by the User......................................................................................15
6.2 Maintenance by the Manufacturer ..........................................................................................15
6.3 Damage Report.......................................................................................................................15
7Troubleshooting....................................................................................................................16
8Spare Parts Overview...........................................................................................................17
8.1 Kit –Order numbers................................................................................................................17
8.2 Spare parts view / Parts lists 2522C-02, 2522B-01, 2534B-01..............................................18
8.3 Spare parts view / Parts lists 2534C-02..................................................................................19
8.4 Spare parts view / Parts lists 2546C-02, 2546B-01................................................................20
EC Declaration of Conformity

Important Information
4 2522-34-46
1 Important Information
1.1 General Information
The WOB-L®Piston Pumps conform to the following directives:
2006 / 42 / EC
Machinery Directive
2014 / 30 / EU
Electromagnetic Compatibility Directive
2014 / 68 / EU
Pressure Equipment Directive
2014 / 29 / EU
Simple Pressure Vessels Directive
The CE sign is located on the rating plate.
Observe the binding national and local regulations when fitting the pump into installations!
1.2 Target Groups
This Operating Manual is intended for the personnel planning, operating and maintaining
WOB-L®Piston Pumps.
This group of people includes:
Designers and fitters of vacuum apparatus
Employees working on commercial laboratory and industrial vacuum technology applica-
tions
Service personnel for WOB-L®Piston Pumps
The personnel operating and maintaining the WOB-L®Piston Pumps must have the techni-
cal competence required to perform the work that has to be done.
The user must authorize the operating personnel to do the work that has to be done.
The personnel must have read and understood the complete Operating Manual before using
the WOB-L®Piston Pumps.
The Operating Manual must be kept at the place of use and be available to the personnel
when required.
1.3 Intended Use
The layout of the WOB-L®Piston Pumps must be appropriate for the conditions of use.
The user bears the sole responsibility for this.
The WOB-L®Piston Pumps may only be operated under the conditions stated
in the "Technical Data" section,
on the type plate, and
in the technical specification for the order concerned.
WOB-L®Piston Pumps are approved for extracting, pumping and compressing gases and
vapours. If these gases and vapours are toxic or explosive, then the user must observe
the currently valid safety regulations for this application.
1.4 Use for an Unauthorized Purpose
It is forbidden to use the pump for applications deviating from the technical data stated on
the type plate or the conditions stated in the supply contract, or to operate it with missing or
defective protective devices.

Important Information
2522-34-46 5
1.5 Safety Devices
Measures such as the following are for the safety of the operating personnel:
electrical connection with a protective conductor (operating mode S1) and an earthing
plug
Motor protection device (thermal)
“Hot Surface" label on the pump - warning notice
The WOB-L®Piston Pumps must not be operated without these elements.
1.6 Meaning of the Warning notes
Take note of the warning notices. They are each in the following box:
CAUTION ! / WARNING !
Hazard which may lead to serious injuries or material damage.
1.7 Product Standards, Safety Regulations
WOB-L®Piston Pumps meet the following product standards:
Observe the standards and regulations applying in your country when you use the WOB-L®
Piston Pumps.
standards:
DIN EN ISO 12100:2011-03 Safety of machinery -
General principles for design - Risk assessment and risk reduction
DIN EN ISO 13857:2008-06 Safety of machinery - Safety distances to prevent hazard zones being reached
by upper and lower limbs
DIN EN 1012-1:2011-02
DIN EN 1012-2:2011-12
Compressors and Vacuum pumps - Safety requirements -
Part 1: Compressors
Part 2: Vacuum pumps
DIN EN ISO 2151:2009-01 Acoustics - Noise test code for compressors and vacuum pumps - Engineering
method (grade 2)
DIN EN 60204-12014-10 Safety of machinery - Electrical equipment of machines -
Part 1: General requirements
DIN EN 61000-6-2:2011-06
DIN EN 61000-6-4:2011-09
Electromagnetic compatibility (EMC) -
Part 6-2: Generic standards - Immunity for industrial environments
Part 6-4: Generic standards - Emission standard for industrial environments
DIN EN 61010-1/A1:2015-04 Safety requirements for electrical equipment for measurement, control and
laboratory use - Part 1: General requirements
DIN EN 50110-1:2014-02 Operation of electrical installations
Directive 2012/19/EUElectrical and electronics - old devices (WEEE)
Directive 2011/65/EUDangerous materials in electrical and electronics devices (RoHS II)
China - RoHS II Environment protection law - China 2016-01
The following additional safety regulations apply in the FR Germany:
BGV A3 Electrical equipment and operating materials
VBG 5 Power-driven machines
BGR 120 Guidelines for laboratories
BGI 798 Hazard assessment in the laboratory
BGG 919 (VBG 16) Accident prevention regulations for "compressors"
BGR 189 (BGR 195;192;197) Use of protective working clothes

Basic Safety Instructions
6 2522-34-46
2 Basic Safety Instructions
2.1 General Information
Warning notices must be observed. Disregarding them may lead to damage to health and
property.
The WOB-L®Piston Pumps must be operated by personnel who can detect impending dan-
gers and take action to prevent them from materialising.
The manufacturer or authorized workshops will only service or maintain the WOB-L®Piston
Pumps if it is accompanied by a fully completed damage report. Precise information about
the contamination (also negative information if necessary) and thorough cleaning of the
WOB-L®Piston Pumps are legally binding parts of the contract. Contaminated WOB-L®
Piston Pumps and their individual parts must be disposed of in ac-cordance with the legal
regulations.
The local regulations apply in foreign countries.
2.2 Electricity
The WOB-L®Piston Pumps of operation mode S1 are supplied. When the location of opera-
tion mode S1 devices is changed, please note that the testing must be repeated in accor-
dance with DIN EN 0105, DIN EN 0702 and BGV A2.
The local regulations apply in foreign countries.
Please note the following when connecting to the electrical power supply system:
The electrical power supply system must have a protective connector according to DIN
VDE 0100-410 (IEC 60364-4-41).
The protective connector must not have any breaks.
The connecting cable must not be damaged.
2.3 Mechanical Systems
Improper use can lead to injuries or material damage. Observe the following instructions:
Only operate the pumps with hoses of the specified dimensions.
The maximum permissible pressure of 1 bar at the suction connection must not be ex-
ceeded.
Hazardous substances must be separated out as far as this is technically possible before
they reach the pump.
External mechanical stresses and vibrations must not be transmitted to the pump. Only
use flexible laboratory hoses for connecting pumps.
The overpressure generated at the pressure port must not exceed 7 bar.
The pump must not be used to suck up fluids. Lay the exhaust pipe so that it slopes
downwards, so allowing condensate to flow out of the pump. Collect the condensate and
dispose of it in an environmentally compatible manner.
Prevent dyes exuding.
Maintain a space of least 20 mm between the pump and adjacent parts in order to enable
the pump to cool.
CAUTION !
Solid particles in the pumping medium impair the pumping action and can lead to
damage. Prevent solid particles penetrating into the pump.

Basic Safety Instructions
2522-34-46 7
2.4 Hazardous Substances
ACHTUNG !
The operating company bears the responsibility for the use of the WOB-L®Piston
Pumps.
Hazardous substances in the gases to be pumped can cause personal injuries and
property damage. Pay attention to the warning notices for handling hazardous sub-
stances.
The local regulations apply in foreign countries.
Combustible, aggressive and explosive Gases
Don’t pump combustible, especially aggressive or explosive gases or vapors or operate this
pump in an atmosphere containing combustible or explosive gases or vapors.
Examine before switching on whether that can form gas combustible gas/air mixtures which
can be promoted! Consider the regulations of the guideline 1999/92/EC.
The WOB-L®Piston Pumps are not certified according to ATEX guidelines 2014/34/EU.
The WOB-L® piston pumps are not recommended for pumping acidic, basic or organic va-
pors.
Poisonous Gases
Use a separator when pumping poisonous or harmful gases. Prevent such substances from
leaking out of the appliance or pump. Treat these substances according to the applicable
environmental protection regulations.
Test the strength and leak-tightness of the connecting lines and the connected apparatus.
Prevent environmental poisons, e.g. mercury, getting into the pumps.
Fulfil the requirements, for example:
German Hazardous Substances Regulation (GefStoffV) of 01. December 2010
Regulation 2016/1179/EU
(classification, packaging and labelling of hazardous substances),
Manufacturer's safety data sheets on hazardous substances.
2.5 High Temperatures
The WOB-L®Piston Pumps may heat up as a result of the temperature of the gas being
pumped and through compression heat.
Prevent the following maximum permissible temperatures from being exceeded.
+ 40 °C for the environment, and
+ 60 °C for the gas to be pumped.
The electric motor has a thermal overload protection.

Description
8 2522-34-46
3 Description
3.1 Design
3.1.1 Connections - Suction-/Pressure side
Suction side - Connection:
Hose nozzle DN 8 (1)
on the Vacuum Regulator (5) with:
- Vacuum Manometer (3)
- Plastic Separator (7)
- Ball check valve (8)
to collect potential liquid, which can
reaching entering the pump.
The Vacuum Regulator allows for
control of the vacuum level between
atmospheric pressure and ultimate
pressure of the pump.
Pressure side - Connection:
Hose nozzle DN 8 (2) or
Exhaust silencer (2a)
on the Pressure Regulator (6) with:
- Pressure Manometer (4)
- Plastic Separator (7)
- Filter (9)
to collect any potential exiting liquid.
The exhaust air is filtered and sound
proof at the same time.
The enables the adjustment of the
air pressure between atmospheric
pressure and maximum overpres-
sure.
Fig. 1 Design WOB-L®Piston Pump (2546)
3.1.2 Connecting to the electricity supply
The WOB-L®Piston Pumps are supplied with complete electrical wiring. It is connected via a
mains connection cable and a power plug. Mains connection cable and plug must comply
with the requirements of the line disconnection devices (current, output).
Motor is provided with a thermal overload protection ex works, protecting the vacuum pump
from damage or destruction, respectively.
WARNING !
Should the user change the electrical connection, for example for fitting into a sys-
tem, then this may only be performed by a electrical specialist under observance of
the accident prevention regulations.
Vacuum
connection
Suction side (1)
Exhaust
connection
Pressure side (2)
(4)
(6)
(7; 9)
(5)
(3)
(7; 8)
(2a)

Description
2522-34-46 9
3.1.3 Display - Vacuum- / Pressure Regulator
The Vacuum Regulator shows pressures at below atmospheric pressure.
The Pressure Regulator gives pressure above atmospheric.
The reference point for both gauges is atmospheric pressure.
WARNUNG !
Please keep in mind that the barometric pressure changes from day to day.
This also changes the displayed pressure values because of latent air pressure
fluctuations.
3.2 Additional protection measures against liquids in the pump
3.2.1 Condensate separator (Suction side)
To prevent accidental ingress of liquids (condensate) in the pump, a plastic separator with
ball check valve is mounted on the suction side regulator.
If the possibility of penetration of larger liquid quantities which exceed the capacity of the
separator, we recommend the additional installation (Fig. 2) of a larger collection vessel (eg.
Woulff bottle).
Fig. 2 Additional separation vessel between the pump and apparatus
3.2.2 Cold trap (Suction side)
The installation of an appropriate cold trap is required when a larger amount of steam (water,
solvent) is obtained which exceeds the tolerance of the vapor pump.
The refrigerant used is usually dry ice or dry ice mixture with an acetone or alcohol.
Maintenance:
The refrigerant must have the highest possible level in the cold trap.
The rise in pressure in the connected vacuum apparatus indicates that the cold trap is satu-
rated.
For cleaning remove the cold trap and defrost. The condensate must be disposed of prop-
erly. The cool trap is, if applicable, clean with a detergent and dry.

Description
10 2522-34-46
3.3 Areas of Application
The WOB-L®Piston Pumps are intended to:
Pumping and compressing neutral and aggressive gases and vapours.
Generating a vacuum down to a minimum ultimate pressure < 80 mbar.
Use in physical and chemical laboratories in trade and industry.
Use for vacuum filtration, vacuum drying, glove boxes, vacuum ovens and other vacuum
technology applications.
3.4 Materials of the medium-affecting pump parts
Component
Materials
Seal
EPDM
Hose nozzle, Valve
Stainless steel
Piston cup seal
PTFE - Compound
Pump head
Aluminium with corrosion protection
Separator vessel
Plastic
3.5 Scope of Delivery
The scope of delivery is specified in the supply contract.
3.6 Accessories
Figure
Designation / Usage
Order no.
Inline filter, hydrophobic
Pore size: 0.22 µm
To protect the pump against fine dust and
aerosols.
Installation in the suction line, as shown.
112555-04
Vacuum hose red, rubber
18 / 8 x 5 mm
For vacuum applications between pump and
apparatus.
828310-4
PVC-Fabric hose
8 x 3 mm
For compressor- and vacuum applications as
exhaust air- and suction line.
828346
Hose clamp
Clamping range 8 –16 mm
For fixing and sealing of PVC fabric hose.
826011-9

Technical Data
2522-34-46 11
4 Technical Data
Parameter
Unit
2522
2534
2546
Pumping speed 50/60 Hz
at atmospheric pressure
m3/ h
1.1 / 1.3
1.7 / 2
2.3 / 2.8
l / min
18 / 22
28 / 34
38 / 46
Ultimate pressure
mbar
133
93
80
Overpressure, max.
bar (ü)
7.9
5.8
5.2
Suction connection
-
Hose nozzle DN 8
for hose inside diameter 8 mm
Pressure connection
Hose nozzle DN 8
for hose inside diameter 8 mm
and Exhaust silencer
Ambient temperature
°C
+ 10 to + 40
Max.
Operating gas temperature
+ 60
Noise level
DIN EN ISO 2151
dB (A)
≤56
Voltage / Frequency
V / Hz
230 / 50; 115 / 60
Motor power
W
93
93
190
Type of protection
DIN EN 60529
-
IP 20
Weight
kg
5.3
Dimensions (W/D/H)
mm
380 / 270 / 310
Order No. for:
-
- WOB-L®Piston pump
230V, 50Hz
inclusive mains connection
cable with plug CEE
2522C-02
2534C-02
2546C-02
- WOB-L®Piston pump
115V, 60Hz
inclusive mains connection
cable with plug US
2522B-01
2534B-01
2546B-01
The information presented in this material is based on technical data and test results of nominal units. It is believed to
be accurate and reliable and is offered as and aid to help in the selection of products.
It is the responsibility of the user to determine the suitability of the product for the intended use and the user assumes
all risk and liability whatsoever in connection therewith.
Gardner Denver Thomas GmbH does not warrant, guarantee or assume any obligation or liability in connection with
this information.

Installation and Operation
12 2522-34-46
5 Installation and Operation
5.1 Unpacking
Carefully unpack the WOB-L®Piston Pump.
Check the pump for:
Transport damage,
Conformity with the specifications of the supply contract (model, electrical supply data),
Completeness of the delivery.
Please inform us without delay if there are discrepancies between the delivery and the con-
tractually agreed scope of delivery, or if damage is detected.
Please take note of the general terms of business of the manufacturing firm.
In case of a claim under warranty, the device must be returned in packaging that is
suitable for protecting it during transport.
5.2 Setting up and connecting
5.2.1 Setting up
Set the pump on a flat and horizontal surface.
Remove the protective caps on the suction and pressure ports.
Note that the cooling of the pump is guaranteed, see chapter 2.3.
Note that on the installation location no moisture acts on the pump.
5.2.2 Connecting
5.2.2.1 Electrical Connection
Before the electrical connection of the pump review the specifications on the nameplate
with the existing electrical connection conditions, see chapter 2.2.
CAUTION !
The electric motor has a thermal overload protection.
After triggering the protective fuse after a certain cooling occurs an auto restart
(Reset) the motor.
5.2.2.2 Vacuum connection (Suction side)
The vacuum connection (suction port) consists of a hose nozzle DN 8.
Suitable vacuum lines are available:
Thick-walled rubber vacuum hose 8 x 5 mm hose nozzle DN 8.
PVC fabric hose and hose clamp 8 x 3 mm clamping range 8 - 16 mm.
Make sure that the vacuum line is kept as short as possible from the pump to the appara-
tus.

Installation and Operation
2522-34-46 13
5.2.2.3 Exhaust connection (Pressure side)
The exhaust connection (pressure port) also consists of a hose nozzle DN 8.
a) Exhaust line for vacuum applications:
Thick-walled rubber vacuum hose 8 x 5 mm hose nozzle DN 8.
PVC fabric hose and hose clamp 8 x 3 mm clamping range 8 - 16 mm.
b) Exhaust line (compressed-air line) with compressor application:
PVC fabric hose and hose clamp 8 x 3 mm clamping range 8 - 16 mm.
CAUTION !
Use only for compressed air applications suitable conduit systems!
5.3 Operation
CAUTION !
Observe the basic safety instructions when using the WOB-L®Piston Pump,
chapter 2.
5.3.1 Start-up
Make sure that when you start the pump, which may arise in the connection lines con-
densates, cannot penetrate into the pump.
►Action: additional suction side condensate separator
Always try to avoid aspiration of foreign body particles!
►Action: suction side inline filter
The WOB-L®Piston pump is switched on the power switch.
It is recommended to let the pump run for a few minutes before use. The warm-up im-
proves the eligibility of the pump.
5.3.2 Decommissioning
If vacuum applications with special steam load, the pump needs to run after the process
with an open vacuum port about 2 minutes and rinsed with atmospheric air.
This measure is used to cleaning the pump chamber and minimizes the corrosive attack
wetted material pump parts.
The WOB-L®Piston pump is switched off using the power switch.

Installation and Operation
14 2522-34-46
5.4 Storage
The pumps are to be stored in a low-dust, interior room within the temperature range from
+ 5 to + 40 °C and at a relative air humidity < 90%.
Leave the protective elements on the suction and pressure ports. Another equally good pro-
tection may be used.
5.5 Scrap Disposal
CAUTION !
The WOB-L®Piston Pumps must be disposed of in accordance with the 2012/19/EU
guideline and the specific national regulations.
Contaminated WOB-L®Piston Pumps must be decontaminated according to the
laws.

Maintenance and Servicing
2522-34-46 15
6 Maintenance and Servicing
WOB-L®Piston pumps are 100% oil-free.
The piston and cylinder of the pump are lubricated maintenance free.
All bearings are sealed and permanently lubricated.
6.1 Maintenance Performed by the User
WARNING !
Only perform the work that is described here, and that which is permitted to be done
by the user.
All other maintenance and service work may only be performed by the manufacturer
or a dealer authorized by him.
Beware of the pump parts being possibly contaminated by hazardous substances.
Wear protective clothing if there is contamination.
Renew defective parts, if necessary! Do not clean with compressed air!
Check the pump daily for unusual running noises and heat building up on the surface of
the pump.
Check the electrical and vacuum connections daily.
6.2 Maintenance by the Manufacturer
Repairs and maintenance going beyond the extent of the work described in chapter 6.1 or
reconditioning or modification may only be performed by the manufacturer or authorized
workshops.
WARNING !
The user shall be liable for the consequences of an incorrect damage report or a
contaminated pump. The statements in the damage report are legally binding.
6.3 Damage Report
You find the form of the damage report to the Download on our web page in the menu "ser-
vice" and "Downloads". www.welchvacuum.com
If you should not have an entrance to the Internet, you can request the form also gladly with
us, under phone [phone].
WARNING !
Incomplete or incorrectly completed damage reports may endanger the service per-
sonnel!
Give full information in the damage report, in particular regarding a possible con-
taminating.

Troubleshooting
16 2522-34-46
7 Troubleshooting
During the warranty period, intervention in the WOB-L®Piston Pumps and accessory com-
ponents may only be made by manufacturing firm.
Trouble
Cause
Remedy
by:
with:
Pump does
not start
No power supply
Qualified
electrician
Check electrical installation
Motor defective
Service
workshop
Exchange
Pump does
not generate
a vacuum or
overpressure
Connected apparatus
and/or
connecting elements
leaking
User or
Service
workshop
Identify and seal the leak,
replace the seals and/or
hoses if necessary.
Pump leaking
Exchange the hoses
and/or fittings if necessary.
Pump dirty
General maintenance /
Cleaning
Valve defective
Exchange
Valves dirty
Cleaning condensates
and foreign objects out of
the valves.
Valves, seals
defective or dirty
Exchange or cleaning
loose screws
User
Tighten the screws
Separator container
is full
Empty the separate container
Running
noise
Pump dirty
User or
Service
workshop
General maintenance /
Cleaning
Valves, seals
defective or dirty
User
Exchange or cleaning
loose screws
or connectors
Tighten the screws
and / or connectors
Cable
defective and/or brittle
Qualified
electrician
Exchange of the cable

Spare Parts Overview
2522-34-46 17
8 Spare Parts Overview
The Spare parts- and Kit lists contain all the parts and all the information necessary for or-
dering.
When ordering, please quote the description, quantity, serial number and order number!
CAUTION !
We are not liable for any damage caused by the installation of any parts not supplied
by the manufacturer.
8.1 Kit –Order numbers
WOB-L®Piston Pump
Service-Kit
Seal-Kit
Foot-Kit
Order no.
Order no.
Order no.
2522C-02
2522B-01
2534B-01
2522K-03
2522K-04
2500K-04
2534C-02
2546K-03
2546K-04
2546C-02
2546B-01
2546K-03
2546K-04

Spare Parts Overview
18 2522-34-46
8.2 Spare parts view / Parts lists 2522C-02, 2522B-01, 2534B-01
Spare parts
Service-Kit
Seal-Kit
Foot-Kit
Item
Piece
Order no.
Designation
Order no.
2522K-03
Order no.
2522K-04
Order no.
2500K-04
1
1
2522K-01
Connecting rod Assembly
1
-
-
2
1
*)
Screw, Handle
2
-
-
3
4
*)
Screw, Head
4
-
-
4
1
*)
Seal, Head
1
1
-
5
1
2565K-02
Valve plate Assembly
1
-
-
6
1
*)
O-Ring
1
1
-
7A
1
*)
Plastic Separator (suction)
1
1
-
7B
1
*)
Plastic Separator (pressure)
1
1
-
8
1
*)
Filter element
1
1
-
9
1
726026
Pressure Manometer 230 V
-
-
-
726025
Pressure Manometer 115 V
-
-
-
10
1
*)
Ball
1
1
-
11
1
726024
Vacuum Manometer 230 V
-
-
-
726021
Vacuum Manometer 115 V
-
-
-
12
1
*)
Seal
2
2
-
13
4
*)
Rubber suction feet
-
-
4
14
1
2522K-06
Pressure Regulator Assembly
-
-
-
15
1
2522K-05
Vacuum Regulator Assembly
-
-
-
16
3
*)
Spare filter
3
3
-
17
1
*)
O-Ring
1
1
-
*) These parts are not sold
separately, but are only
available in respective kit.

Spare Parts Overview
2522-34-46 19
8.3 Spare parts view / Parts lists 2534C-02
Spare parts
Service-Kit
Seal-Kit
Foot-Kit
Item
Piece
Order no.
Designation
Order no.
2546K-03
Order no.
2546K-04
Order no.
2500K-04
1
1
2534K-01
Connecting rod Assembly
1
-
-
3
4
*)
Screw, Head
4
-
-
4
1
*)
Seal
1
1
-
5
1
2567K-02
Valve plate Assembly
1
-
-
6
1
*)
O-Ring
1
1
-
7
2
*)
Plastic Separator (suction / pressure)
2
2
-
8
1
*)
Filter element
1
1
-
9
1
726026
Pressure Manometer 230 V
-
-
-
10
1
*)
Ball
1
1
-
11
1
726024
Vacuum Manometer 230 V
-
-
-
12
2
*)
Seal
2
2
-
13
4
*)
Rubber suction feet
-
-
4
14
1
2522K-06
Pressure Regulator Assembly
-
-
-
15
1
2522K-05
Vacuum Regulator Assembly
-
-
-
16
1
*)
Piston cup
-
1
-
17
1
*)
Retainer screw
-
1
-
18
1
*)
O-Ring
1
1
-
*) These parts are not sold
separately, but are only
available in respective kit.

Spare Parts Overview
20 2522-34-46
8.4 Spare parts view / Parts lists 2546C-02, 2546B-01
Spare parts
Service-Kit
Seal-Kit
Foot-Kit
Item
Piece
Order no.
Designation
Order no.
2546K-03
Order no.
2546K-04
Order no.
2500K-04
1
1
2546K-01
Connecting rod Assembly
1
-
-
3
4
*)
Screw, Head
4
-
-
4
1
*)
Seal
1
1
-
5
1
2567K-02
Valve plate Assembly
-
-
-
6
1
*)
O-Ring, Cylinder
1
1
-
7
2
*)
Plastic Separator (suction / pressure)
2
2
-
8
1
*)
Filter element
1
1
-
9
1
726026
Pressure Manometer 230 V
-
-
-
726025
Pressure Manometer 115 V
-
-
-
10
1
*)
Ball
1
1
-
11
1
726024
Vacuum Manometer 230 V
-
-
-
726021
Vacuum Manometer 115 V
-
-
-
12
2
*)
Seal
2
2
-
13
4
*)
Rubber suction feet
-
-
4
14
1
2522K-06
Pressure Regulator Assembly
-
-
-
15
1
2522K-05
Vacuum Regulator Assembly
-
-
-
16
1
*)
Piston cup
-
1
-
17
1
*)
Retainer screw
-
1
-
18
1
*)
O-Ring
1
1
-
*) These parts are not sold
separately, but are only
available in respective kit.