GE MONOGRAM ZIC360NR Manual

Specification Created 5/04
110100
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
For answers to your Monogram,
® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
The Installation Space
The finished cutout width must be 35-1/2".
Product Dimensions
* Shipping Height. The
refrigerator can be
adjusted to fit into a
cutout that is 83-1/2" min.
to 84-1/2" max. height.
The top case trim at the
front is 1/2" higher and
will overlap upper
cabinetry or soffit.
Use leveling legs and
wheels for a maximum
1" height adjustment.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent cabinetry,
depending on your installation.
The cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the 24"
installation depth shown. The top case trim overlaps the bottom
of the soffit.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An individual
properly grounded branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
All models are equipped with an automatic icemaker. The water line can
enter the opening through the floor or back wall. Route GE SmartConnect™
Kit or 1/4" O.D. copper tubing between the cold water line and the water
connection location at the front of the refrigerator. The installation of an
easily accessible shut-off valve in the water line is required.
696Dia7
6"
Wall View
Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
75" From
Floor to
Bottom
of Electrical
Area
10"
5"
3 1/2"
5"
3 1/2"
Water Supply
24" Cutout Depth
35-1/2"
Finished Width
2-5/16"
605Dia20
25"
Min. to
Wall
130°
130° Door Swing
23-7/8"
Behind
Frame
36-3/4"
605Dia21
90°
90° Door Swing
4" Min.
to Wall
2-5/16"
75" From
Floor to Bottom
of Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
71-1/2" Finished Width
Electrical
5"
3-1/2"
24" Cutout
Depth
Water Supply
Wall View
696Dia8
24-3/16"
26"
6"
10"
10"
Water Supply
26"
5"
3-1/2"
Door Swing Clearances
The installation must allow for clearances to adjacent walls or cabinets.
These refrigerators are equipped with a 2-position door stop. The
factory-set 130° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
Allow 25" minimum clearances for a full 130° door swing. Allow 15"
for pan removal.
• 4" minimum clearance is required when the door swing is adjusted to
90°. If the 90° door stop position is used, pan access is maintained,
but pan removal is restricted.
• See door swing illustrations to determine interaction with adjacent
cabinets or countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators side by side, the installation space
must be 71-1/2" wide.
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout to calculate
rough-in width.
• The water and electrical locations for each product must be located
as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for
each product.
429Dia9
*84" From
Floor to
Top Frame
35"
Case Width
*83-1/2"
at
Rear
Case Depth:
25-3/8" Framed Models
25-3/4" Stainless Steel Models
Depth Including Handles:
26-7/8" Framed Models
27-3/4" Stainless Steel Models
36"
Frame to Frame Width

Specification Created 5/04
110100
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
729Dia65
Standard Door Handle Framed Panel
Standard
Door Handle
3/4" Overlay Panel
1/4" Thick Backer Panel
.10" Thick Spacer Panel
696Dia9
Customization Basics: Framed or Overlay Panels,
Custom Handles and Accessory Kits
These bottom-freezer refrigerators are factory set for a left or right
door swing. The door swing is NOT reversible. Choose an RH model
with hinge on the right side; the door swings left to right. Choose an
LH model with hinge on the left side; the door will swing right to left.
Standard supplied handles shown in 1/4" panel position.
Standard supplied handles shown in 3/4" overlay panel position.
Overlay Panels
You may also choose to install custom overlay panels from your cabinet
manufacturer. This design provides a seamless appearance which
integrates smoothly with surrounding cabinetry.
Door Handles
The supplied handles can be adjusted to accommodate both framed
or overlay panels. Custom handles of your choice, supplied by your
cabinetmaker, can also be installed. If desired, you may order ZKHCSS2
Monogram® Stainless Steel Tubular Handle Kit for overlay panels.
Side Panels
Side panels must be used whenever the sides of the refrigerator will
be exposed.
Optional Accessory Kits
ZKHCSS2: Monogram Stainless Steel Tubular Handle Kit and Handle
Side Trim for custom handles. For use on 3/4" custom panels.
ZUG2: For side-by-side installation of two trimmed bottom-freezer
refrigerators. This kit provides for the installation of a unified custom
grille panel to span the width of two units using a framed or overlay panel.
ZUGSS2: For side-by-side installation of two stainless steel-wrapped
bottom-freezer refrigerators. This kit provides a unified stainless steel
grille panel to span the width of two units.
Accessory Panels
White or black acrylic and stainless steel accessory panels are available
from your Monogram supplier. Panels are cut to size and ready to install.
These panel kits must be ordered separately.
Black White Stainless Steel
ZPBC360 ZPWC360 ZPSC360
605Dia26
Right-Hand
Door Swing
Left-Hand
Door Swing
Trimmed Refrigerators
ZIC360NRLH, ZIC360NRRH
Trimmed refrigerators are designed to be customized with decorative
panels. Field-installed custom door and grille panels are required.
Framed Panels
You may install 1/4"-thick custom panels from your cabinet
manufacturer. The decorative panel or accessory panel slides
into the factory-installed trim.
For answers to your Monogram,
® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
R
Listed by
Underwriters
Laboratories

Specification Created 5/04
110100
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
1/4" Framed Panel Dimensions 3/4" Overlay Panel Dimensions
If you choose to install framed panels,
they must be cut to the dimensions
shown. The panels will slide into the
frame on the door, drawer and grille.
If the custom panel is less than 1/4"
thick, and it fits loosely in the door
frame, it can be backed up with a
piece of filler material or foam tape
to improve the fit.
Important Note: Maximum weight for
fresh food panel is 50 pounds,
30 pounds for freezer drawer panel
and 11 pounds for the grille panel.
729Dia84
1/4"
Panel
Door/Drawer
5/16"
Trim
Reveal
For a more custom appearance, overlay
panels may be installed on trimmed
models. The overlay panel must be
secured to a 1/4"-thick backer panel
which slides into the trim. A spacer
panel 0.10" thick must be placed
between the overlay and backer panel.
729Dia42
Overlay
Panel
1/4"
Backer
Panel
Door/Drawer
.10"
Spacer
Fresh Food
Panel
729Dia89
Freezer Drawer
Panel
D
C
A
B
Grille Panel
Framed Panel Dimensions (in inches)
A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
1/4" Framed Panel 33-7/8 8-7/8 46-1/16 21-7/8
3/4" Overlay Panel Dimensions (in inches)
A (Width) B (Grille Ht.) C (FF Ht.) D (FZ Ht.)
1/4" Backer Panel 33-7/8 8-7/8 46-1/16 21-7/8
.10" Spacer Panel 32-1/2 7-5/8 44-11/16 20-1/2
3/4" Overlay Panel 34-1/8 9 46-5/16 22
Center each panel over
the other. Assemble the
panels with glue and
screws. Screws must
be countersunk into the
backer panel.
605Dia15
Spacer Panel
Overlay Panel
Backer Panel
729Dia85
A
B
Grille Panel
.250" + .10" + .750" =
1.100" Total Panel Thickness
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
ZUG2 Grille Panel Dimensions
The ZUG2 Unified Grille Panel Kit will accept a framed or overlay
grille panel.
• Assemble the overlay panel in the same manner as the door and
drawer panels.
Framed Panel Dimensions
A (Width) B (Height)
1/4" Framed Panel 69-7/8" 8-7/8"
Overlay Panel Dimensions
A (Width) B (Height)
1/4" Backer Panel 69-7/8" 8-7/8"
.10" Spacer Panel 68-1/2" 7-5/8"
3/4" Overlay Panel 70-1/8" 9"
For answers to your Monogram,
® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
R
Listed by
Underwriters
Laboratories

1/4" 1/2" 3/4" 1" 1-1/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Stainless Steel
1/4"
1/2"
3/4"
2"
1-1/4"
1-1/2"
1-3/4"
3"
2-1/4"
2-1/2"
2-3/4"
1/4"
1/2"
3/4"
Door
23-7/8" From
Rear of
Refrigerator
1"
Refrigerator
Case
Trim
For answers to your Monogram,
® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Frameless Cabinets: The case trim overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require filler strips to prevent interference
with cabinet door swing. The opening must allow for filler strips.
Use this page to determine door
swing interaction with adjacent
cabinets or countertops.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Specification Created 5/04
110100
Top View
130° Door Swing
(Optional setting)
Scale 1:1

1/4"
1/2"
3/4"
1"
1-1/4"
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
23-7/8"
From Rear of
Refrigerator
3/4" Overlay
Panel
(Nominal Size)
Case Trim
Refrigerator
Door
Stainless Steel
Top View
90° Door Swing
(Optional setting)
Scale 1:1
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
Use this page to determine door
swing interaction with adjacent
cabinets or countertops.
ZIC360NM – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
For answers to your Monogram,
® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Advance Planning for Built-In Custom Bottom-Freezer Refrigerators
Specification Created 5/04
110100

Specification Created 5/04
110100
ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator
with Automatic Icemaker
Features and Benefits
• 20.6 Cu. Ft. Capacity
• Upfront electronic controls with digital readout
• Multi-shelf air management tower
• 2 Sealed, adjustable humidity vegetable/fruit pans with
easy access lids and full extension slides
• 2 Sealed deli pans with full extension slides
• Adjustable spillproof glass cabinet shelves
• Slide-out freezer compartment with full
extension slides
• Model ZIC360NRRH – Right-handed door swing
(Door panels required)
• Model ZIC360NRLH – Left-handed door swing
(Door panels required)
ZIC360NRLH.EPS