Genie HDMC221CPV2 User manual
User Manual
Please read these instructions carefully before operating the unit
and keep for further reference.
2.1MP HD-SDI Encapsulated
Camera with 4.3mm Conical
Pinhole Lens
HDMC221CPV2
ii
Intro Section
Please read this instruction carefully before operating the product and keep it for
further reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
CAUTION:
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
• To help prevent electric shock, plug the equipment and peripheral power
cables into properly polarized or grounded electrical outlets. These cables are
equipped with the wide blade or the third prong to ensure proper grounding.
• Do not use adapter plugs or remove the grounding prong from a cable. If the
provided plug does not fit your outlet, consult an electrician.
• 10) Ensure that nothing rests on your equipment’s cables and that the cables
are not located where they can be stepped on, tripped over, or pinched.
• Only use attachments or accessories as specified.
• Only use the equipment with the cart, stand, tripod, bracket, or table that is
specified by the manufacturer or sold with the apparatus. When a cart is used,
use caution to prevent the cart from tipping over and to avoid injury.
• Do not connect or disconnect during lightning storms due to risk of electric
shock.
• If any of the following conditions occur, unplug the equipment from the
electrical outlet and replace the part or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the equipment.
• The equipment has been exposed to water.
• The equipment has been dropped or damaged.
• The equipment does not operate correctly when you follow the operating
instructions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Components.................................................................................................4
1.4 Mounting Position ........................................................................................4
1.5 Specification ................................................................................................5
2.0 Installation ...........................................................................................................6
2.1 Monitor Connection .....................................................................................6
2.2 RS-485 Type.................................................................................................6
3.0 OSD Manual..........................................................................................................7
3.1 Function Description....................................................................................8
4.0 RS-485..................................................................................................................11
4
The Genie HDMC221CPV2 is a 2.1MP HD-SDI encapsulated camera with a 4.3mm
conical pinhole lens.
1.1 Product Features
• 1/2.8” Progressive Scan CMOS
• 1080p (1920×1080) @ 30 (25)fps
• EX-SDI/HD-SDI/CVBS output
• Conical pinhole lens 4.3mm
• Electronic Day & Night
• WDR, 3D DNR, Defog
• RS485 or AD KEY
• 30×30mm Mini square camera
1.2 Product Dimensions
1.3 Components
• Camera
• Mounting bracket
• Screws (Tapping and M2)
• Operational manual
• DIY cable
1.4 Mounting Position
1.0 Introduction
NOTE:
Install in the order shown.
9.9mm 30mm
14mm
30mm
User Manual 2.1MP HD-SDI Encapsulated Camera with 4.3mm Conical Pinhole Lens
5
1.5 Specification
Camera
Image Sensor 1/2.8” SONY Exmor R Progressive Scan CMOS
Resolution
HD-SDI/EX-SDI1.0_2.0_2.1: 1080p @ 30fps (25fps) / 720p @
60fps (50fps) / 720p @ 30fps (25fps)
TV out: CVBS NTSC / PAL (720H)
Electronic Shutter AUTO / FLICKER / MANUAL /(1/30(25)~1/30,000)
Digital Slow Shutter (DSS) OFF~ x32
Minimum Illumination 0.2 Lux (F2.0, AGC33dB, DSS:x2)
Lens 4.3mm
Effective Pixels 1945(H) x 1097(V)
Functions
White Balance AUTO/AUTO EXT/PUSH LOCK/MANUAL
Level 135.6dB
D-WDR Off/On
WDR/BLC OFF/BLC/HLC/WDR
Auto Gain Control (AGC) OFF~45dB
Day&Night AUTO/COLOUR/B&W (Electronic D&N)
Noise Deduction 3D-DNR (OFF/Low/Middle/High)
Motion Detection OFF/ON (4 Zones)
Privacy Mask 16 Zones
Image Rotation OFF/H-FLIP/V-FLIP/HV-FLIP
Defog OFF/ON(AUTO/MANUAL)
Sharpness Adjustable (0~10)
OSD Control Cable JOYSTIC, RS-485 Control (Option)
Language 8 languages
Video Output HD-SDI/EX-SDI1.0/EX-SDI2.0/EX-SDI2.1/CVBS
Others
Power Supply DC12V (±10%)
Power Consumption Max.150mA @ DC12V
Temperatue -10°C~+50°C (Operating)
-20°C~+60°C (Storage)
Dimensions 30 × 30 mm
Weight Approx.28.9g (Board lens)
6
Basic Specification
Option Specification
2.0 Connection
7
3.0 OSD Manual
User Manual 2.1MP HD-SDI Encapsulated Camera with 4.3mm Conical Pinhole Lens
8
9
4.0 Hidden Menu
4.1 Convert SDI Output Mode
STEP 1. ENTER
RS485 : Press [LEFT] → [LEFT] → [RIGHT] →[RIGHT] key.
AD-KEY : Press UP/DOWN/LEFT/RIGHT key 3 times.
STEP 2. SELECT
Press UP key 5 times : EX-SDI 2.1
Press DOWN key 5 times : EX-SDI 2.0
Press LEFT key 5 times : HD-SDI
Press RIGHT key 5 times : EX-SDI 1.0
STEP 3. CONFIRM
If the ‘YES’ is not checked within 30sec, the value returns to the previous setting.
10
5.0 RS-485
5.1 Communication Specification
5.2 PELCO Protocol for OSD Remote Control
PELCO-D
PELCO-P
Table of contents
