Giant NeosGPS User manual

NeosGPS
Operation Manual

Table of Contents
2 Table of Contents
Getting Started................... 3
NeosGPS Button
Introduction..................................... 3
Restart NeosGPS............................. 3
Accessories ....................................... 4
Status Icon ........................................ 4
Step 1: Charging your
NeosGPS............................................ 5
Step 2: Turn On NeosGPS............ 5
Step 3: Initial Settings................... 5
Step 4: Connecting to
Satellite Signal ................................ 6
Step 5: Start Riding With
NeosGPS............................................ 6
Step 6: Share Your Records ........ 6
Sync Records to the Giant
NeosTrack App................................ 7
Setup...................................... 10
Units of Measurement.................. 10
Time Display .................................... 10
Altitude Calibration....................... 11
Start Biking ....................................... 11
Enable GPS........................................ 12
Sensor Pairing ................................. 12
Delete Records................................ 13
Adjust Odometer ........................... 13
Giant NeosTrack App
Advanced Settings............ 14
Stopwatch Information ............... 14
Altitude Calibration....................... 15
Smart Notications ................ 16
Appendix.................................... 17
Specications ........................................17
Install NeosGPS.....................................18
Install Smart Speed/Cadence
Sensor (optional)..................................19
Install Smart Heart Rate Monitor
Belt (optional) ....................................... 20
Wheel Diameter and
Circumference....................................... 21
NeosGPS Basic Maintenance ...........22
Digital Information..............................23
Declaration of the Presence
Condition of the Restricted
Substances Marking ........................... 24
Warning
Consult your physician before starting any training.
Please read the "Warranty and Safety Information" guidelines included with your product.

3 Getting Started
Getting Started
This section explains the basic setup procedure before using your NeosGPS.
NeosGPS Button Introduction
Restart NeosGPS
Press and hold the ( / / ) keys to restart NeosGPS.
Power/OK ( )
• Press to turn on the device.
• Press and hold to turn the device off.
• Press to enter/leave the "Menu" page.
Change Page ( )
• Press this button to start recording in the
free biking mode.
• Press to stop recording when in the
exercise data logging mode.
• Press DOWN key to enter or validate
options in the "Menu" page.
Backlight/Page ( )
• Press and hold to turn the backlight
on/off.
• Press DOWN key to scroll down the
menu options in the "Menu" page.
• Press DOWN key to switch in
between the stopwatch pages in the
"Stopwatch" mode.
• Page Up/Down: Press to view biking
pages in the information mode.

4 Getting Started
Accessories
NeosGPS comes with the following accessories:
•
USB charging cable
Optional accessories include:
• GIANT HEART RATE SENSOR(410000075)
• RideSync/Garmin & Gopro Mount
for 31.8mm Round Bars (410000072)
• RideSync/Garmin & Gopro Mount for
Contact SLR Aero Handlebars (410000073)
• Bicycle mount
Status Icon
/
AM
PM
S
C
REC
Icon Instructions Icon Instructions Icon Instructions
Bike in Use Now
GPS Signal Status
Battery Charge Status
No Signal
(not positioned)
Poor Signal
Good Signal
Fully Charged
Battery Charge OK
Battery Charge Low
Bike 1
Bike 2
Daylight Saving
Time
Backlight
Slope
Total Ascending
Height
Total Descending
Height
Ride Time
Trip Time
Heart Rate Sensor
Paired
Speed Sensor Paired
Cadence Sensor
Paired
Riding Data
Recording
Bluetooth
Connected
Odometer
Maximum Value
Average Value
AM
PM
Choose 12 or 24
Hour Clock
Setup
Stopwatch Information
Accessory Pairing
Note:
• Accessory icons will display on the status bar when paired.

5 Getting Started
Step 1: Charging your NeosGPS
Remove the USB cable from the packaging and connect your NeosGPS to your computer for auto
charging. Please charge it for at least 4 hours. Remove the USB cable once it is fully charged.
fully charged.
• Charge your battery in a temperature range of 0°C-40°C (32°F - 105°F) or the charging will stop
and the device will consume battery power.
Step 2: Turn On NeosGPS
Press the button to power on your device.
Step 3: Initial Settings
complete the setup. (Please refer to page 10 for detailed settings)
1.Press to choose measurement units.
Charge NeosGPS
at least 4 Hours

6 Getting Started
Step 4: Connecting to Satellite Signal
Once the NeosGPS is powered on it will start searching for satellite signals automatically. It may take
30 to 60 seconds to receive satellite signals. Please acquire GPS positioning before using it for the
rst time.
The GPS signal icon ( / ) will display after the GPS is positioned successfully.
• If GPS positioning fails, the icon will display.
• DO NOT search for a GPS signal in the following environment as the latter may interfere with
signal reception.
Step 5: Start Riding With NeosGPS
• Easy Ride:
NeosGPS will detect the motion of your bike starting and stopping automatically.
• Start Riding and Record Data:
Press to start recording and press again to stop.
In Tunnels Indoor/Within
building/
Underground
Underwater High Voltage
Cables or TV
Tower
Construction
Site or in Trac
Jams
Step 6: Share Your Records
Share Your Records to the NeosTrack website
1.Register or log in.
a. Visit https://www.NeosTrack.com.
b. Register a new account.
2.Connect the device to a computer.
Power on the NeosGPS and connect it to your computer with a USB cable.
3.Share your records.
a. Click the "+" symbol in the upper right corner to add new activity entries.
b. Drag and drop FIT, BDX, or GPX les or click "Select le" to upload.
c. Click "Activity Log" to view just uploaded records.

7 Getting Started
Share Your Records to Strava.com
1. Register or log in to Strava.com.
a. Visit https://www.strava.com.
b. Register a new account or log in with your active Strava account.
2. Connect the device to a computer.
Power on the NeosGPS and connect it to your computer with a USB cable.
3. Share your records.
a. Click the "+" symbol in the upper right corner and click "File".
b. Click "Select File", then select the desired FIT les from the GIANT folder to upload them.
c. Input relevant riding information, click the "Save and View" key to upload them.
Sync Records to the Giant NeosTrack App
Start Using the Giant Mobile App
1. Download the Giant Mobile App.
Scan the QR Code at the bottom of the page to download the Giant NeosTrack APP or search for
and download it in the Google Play/App Store.
2. Register with the Giant NeosTrack APP.
a. Open the Giant NeosTrack APP.
b. Register a new account.
Note: Sync the Giant NeosTrack APP with NeosTrack.com. Please log in NeosTrack.com with
your existing account, otherwise create a new one.

Bluetooth Sync
8 Getting Started
Bluetooth Pairing With the Giant NeosTrack App
NeosGPS can sync wirelessly with a Bluetooth connection. Please pair NeosGPS with the NeosTrack
App before any sync to enable correct records synchronization.
One-click Record Upload
After the device is successfully paired with the Giant NeosTrack App and the Bluetooth connection
remains active, you may click to auto upload all records to the Giant NeosTrack App.
a. Enable the "Bluetooth" function
of your cell phone.
b. Press the Power key to enable
NeosGPS.
c. Click "Bluetooth Sync" to
maintain the networking function.
d. Select MySetup > Device
Manager >and Press the "+" key.
e. Select Bluetooth 4.0. f-1. Select the NeosGPS for pairing +.
f-2. Press "OK".
f-3. Your device has successfully
paired with the Giant NeosTrack
App, tap to complete.
g. Start uploading records from
the paired device.
h. All records uploaded. i. Go to the "Activity Log" to see
uploaded records.

9 Getting Started
Software Updates
Note: NeosGPS software features regular updates for quicker GPS positioning and optimization. It is
recommenced that you check for new updates every two to four weeks.
1. Check this website to see if there is a newer version.
www.giant-bicycles.com/download
2. Connect to the USB port of a computer, save les in NeosGPS folder.
3. Unplug the USB cable once the operation is completed and the NeosGPS will start updating
automatically.
Identify Whether Your NeosGPS is the Latest
Version
1. Connect the NeosGPS to computer with a USB cable.
2. Click System -> Device to view the edition of the current model and release.

You may customize the following functions with the "Setup" function: unit of measure, daylight
saving time, current altitude, bike, wheel diameter, sensor pairing and odometer.
Unit of Measure
You may choose KM/H or MI/H for UOM display.
1. Press to enter the UNIT setup page.
2. Press -> and
3. Press to validate the selection made.
4. Press to exit setup.
1. Press to enter the setup page.
2. Press to select HOUR, press and the HOUR
setup page will display.
3. Press to select 12h or 24h, press to validate the
selection made.
4. The daylight saving time page of the NeosGPS
display, press to select the desired number, press
to validate the selection made and proceed to the
next one. Repeat the above steps to complete the
setting. Press to return to the main setup page if
no changes are required and press again to exit.
5. Once all settings have been made, press to
validate the selections made and exit back to
the main setup page and press to exit.
Setup
10 Setup
- or 0
1 or 2
00 or 30
Select
Number
Time Display
You may select 12 or 24 hour time format and set up daylight saving time here.

Altitude Calibration
You may calibrate the current altitude.
Start Biking
You may select bikes to enable and modify wheel diameter.
1.Press to enter the setup page.
2.Press to select ALT, press and the ALT setup page
will display.
3.Press to select the desired number, press to
validate the selection made and proceed to the next
one. Repeat the above steps to complete the setting.
1.Press to enter the setup page.
2.Press to select BIKE, press and the BIKE setup page
will display.
3.Press to select BIKE1 or BIKE2, press to validate the
selection made.
4.The wheel diameter page of the NeosGPS will display,
press to select the desired number, press to validate
the selection made and proceed to the next one. Repeat
the above steps to complete the setting.
Press to return to the main setup page if no changes
are required and press again to exit.
4.Once all settings have been made, press to
validate the selections made and press to exit.
5.Once all settings have been made, press to validate
the selections made and exit back to the main setup
page and press to exit.
0~9
0~9
0~9
0~9
11 Setup
OK
Note: Once the current altitude value in Settings is changed its counterpart in the
stopwatch mode will change accordingly.
Note: Please refer to "Wheel Diameter and Circumference"
on page 24 for details on wheel dimension.
Select
Number
- or 0
0~9
0~9
0~9
0~9
OK
Select
Number

Enable GPS
Please disable GPS signaling in the event of indoor exercise to prevent recording less accurate ride
information.
Sensor Pairing
NeosGPS supports Bluetooth peripheral sensors. Please follow the steps below to pair.
1.Press to enter the setup page.
2.Press to select GPS, press and the GPS setup
page will display.
3.Press to select ON or OFF, press to validate the
selection made.
4.Once all settings have been made, press to
validate the selections made and exit back to the
main setup page and press to exit.
1.Press to enter the setup page.
2.Press to select SYNC, press and the SYNC setup
page will display.
3.Press to select HR or SP-CA, press to validate the
selection made.
4.Wake up the sensor by putting on the heart rate
belt, or pedaling the crank and wheel.
5.NeosGPS prompts the message "YES" when it
detects the sensor successfully; press to validate
the pairing; press to select "NO" and to cancel
the pairing and start scanning again.
6.Once all settings have been made, press to exit
the setup page.
12 Setup
Note: The sensor can be paired only in standby mode;
otherwise it will enter sleep mode to conserve battery
charge.
Note:
• Keep away from other Bluetooth sensors when pairing.
• After successful pairing, the NeosGPS smart sensor will auto connect to the device once it is awoken.

Delete Records
You may delete all or some records for the device to log at least 8, 16 or 24 hours of riding data.
Adjust Odometer
You may adjust odometer.
1.Press to enter the setup page.
2.Press to select DEL, press and the DEL setup
page will display.
3.Press to select >8h,>16h, >24h or ALL, press to
validate the selection made.
4.Once all settings have been made, press to
validate the selections made.
5.Press to exit the setup page.
1.Press to enter the setup page.
2.Press to select ODO, press and the ODO setup
page will display.
3.Press to select the desired number, press to
validate the selection made and proceed to the
next one. Repeat the above steps to complete the
setting.
4.Once all settings have been made, press to
validate the selections made and exit back to the
main setup page and press to exit.
13 Setup
Note:
• NeosGPS may log up to 120 hours of biking in the smart recording mode and up to 30 hours of biking by
entry-per-second mode.
• When you start riding or press to start recording, the number of hours left for recording display in cells
at the center of the page.
• Options ">8h", ">16h", and ">24h" work only when the storage space of the device can last less than 8h,
16h, 24h. Select these options to record at least 8h, 16h, and 24h more rather than another 8h, 16h and
24h.
0~9
0~9
0~9
0~9
0~9
OK
Select
Number

After NeosGPS is paired with the Giant NeosTrack App, you can change the stopwatch
information and correct the altitude.
Custom Page Information
You may change the stopwatch information page, set up MHR (Max Heart Rate) and LTHR
(Lactate Threshold Heart Rate), enable/disable smart pause, and data recording frequency
according to your training objectives.
1. Pair NeosGPS With the Giant NeosTrack App
a. Open NeosGPS.
b. Enable the Bluetooth function of your cell phone.
c. In the Giant NeosTrack App, click through Setup > User Setup > Device Management.
d. Press the "+" key and select Bluetooth 4.0.
e. Select the device you want to pair with then click the "+" key.
f. Click "Pair" to pair your device with your phone (for iOS devices only).
g. Validate UUID of the paired device and click "Yes".
h. Click Finish.
2. Change Your Stopwatch Information Page
a. Click Setup > Stopwatch Information in the Giant NeosTrack App.
b. Click the "OK" key to enable connection with the device.
c. Select the manual mode to adjust the information page.
Select Auto to maintain the factory mode.
d. Click "<" or ">" to change the number of information cells.
e. Tap 1, 2, 3, 4, or 5 to switch the information page.
f. Click the device page information cell to change riding information.
3. Input Your MHR and LTHR
a. Click to enter the setup page.
b. Click MHR and LTHR to input your MHR and LTHR value.
4. Enable/Disable Smart Pause
5. Set up Data Record
Click the data record column to change to the desired settings.
6. Sync Setup to NeosGPS
Click the "<" in the upper left corner and select "Sync" to apply changed settings to
NeosGPS.
Giant Advanced Settings
14 Giant App Advanced Settings
Note:
•To reset your stopwatch back to its factory default settings: tap and tap "Yes" in the
"Reset to factory default?" dialog prompt.

Altitude Calibration
When connected to the Internet, the Giant NeosTrack App will provide you with the
altitude of your current location so that you can calibrate it automatically or manually.
1. Pair NeosGPS With the Giant NeosTrack App
a. Open NeosGPS.
b. Enable the Bluetooth function of your cell phone.
c. In the Giant NeosTrack App, click through Setup > User Setup > Device Management.
d. Press the "+" key and select Bluetooth 4.0.
e. Select the device you want to pair with then click the "+" key.
f. Click "Pair" to pair your device with your phone (for iOS devices only).
g. Validate UUID of the paired device and click "Yes".
h. Click Finish.
2. Calibrate Altitude
a. Click the "Altitude Calibration" option in the Giant NeosTrack App.
b. Click to permit the Giant NeosTrack App to access altitude data contained in the
current position.
c. The Giant NeosTrack App displays the altitude of your current position. You may
change it by pressing or click the altitude eld to input the value.
d. Click "Calibration".
e. The Giant NeosTrack App begins detecting devices ready for connection. Click OK to
connect to your NeosGPS.
f. Click "Yes" to validate altitude calibration.
g. The calibration completion message appears, click to acknowledge.
15 Giant App Advanced Settings

Pair your smart phone with NeosGPS through smart wireless Bluetooth technology to
1. Pair With an iOS Cell Phone
a. Turn on NeosGPS.
b. Enable the Bluetooth function of your cell phone.
c. In the Giant NeosTrack App, click through Setup > User Setup > Device Management.
d. Press the "+" key and select Bluetooth 4.0.
e. Select the device you want to pair with then click the "+" key.
f. Click "Pair" to pair your device with your phone.
g. Validate UUID of the paired device and click "Yes".
1. Pair With an Android Cell phone
a. Open NeosGPS.
b. Enable the Bluetooth function of your cell phone.
c. In the Giant NeosTrack App, click through Setup > User Setup > Device Management.
d. Press the "+" key and select Bluetooth 4.0.
e. Select the device you want to pair with then click the "+" key.
f. Validate UUID of the paired device and click "Yes".
g. Click Finish.
Note:
as well as the reminder settings in community apps.
POP OUT Notifications

Appendix
NeosGPS
17 Appendix
Specications
Item Instructions
Stopwatch Information
Display
Dimensions 71 x 46.2 x 16.5 mm
Weight 52g
Operating Temperature -10°C~50°C
Battery Charging
Temperature 0°C~40°C
Battery Lithium battery
Battery Service Time In open sky for 16 hours
GPS Integrated high-sensitivity receiver with built-in planar antenna
Waterproong
Pneumatic Altimeter
Waterproof for 30 minutes in 1 meter deep water
Built-in pneumatic altimeter
Smart wireless Bluetooth technology with built-in planar antenna
2” code break HTN LCD
Smart Bluetooth
Item Instructions
Dimensions 36.9 x 34.8 x 8.1 mm
Weight 6 g
Waterproong Waterproof for 30 minutes in 1 meter deep water
Transmission Scope 3 m
Battery Service Time It may last 9 months if you use it for one hour each day
Operating Temperature -10°C~60°C
Radio Frequency/
Communication Protocol
2.4GHz/smart Bluetooth and Dynast ream ANT + Sport wireless
communication protocol
Smart Speed Sensor
Note: Poor sensor contact, electrical and magnetic interference, and long distance between
receiver and transmitter may hamper accuracy.
Please install sensors on the front wheel in the event of outdoor biking as the rear one usually
suers from a more complex environment; in the event magnetic interference problems persist,
try biking in another location, or washing or replacing the chain.

4.Once all settings have been made, press to
validate the selections made and exit back to the
main setup page and press to exit.
3
1 2
4
12
18 Appendix
Install NeosGPS
Mount NeosGPS to a Bicycle Mount
Use a Circular/Flat Tube Headlight Stopwatch Base to Install
NeosGPS (optional)

19 Appendix
Install Smart Speed/Cadence Sensor (optional)

20 Appendix
Electrode
O
P
E
N
Install the "Smart Heart Rate Monitor Belt"
(optional)
Note:
• Please wear appropriate clothing to keep the heart rate belt in the required temperature.
• DO NOT wear your heart rate monitor over clothing; wear it directly on your body instead.
• Position the sensor in the middle of your body (wear it below the chest). Point the Giant logo
shown on the sensor upward; secure the elastic band to prevent it from falling o during
exercise.
• If the sensor fails to detect temperature or the reading looks abnormal, please warm it up for
about 5 minutes.
• Detach the sensor from the heart rate belt and keep them isolated from each other if you are
not to use them for an extended period of time.
• When the battery of the heart rate monitor belt is low on charge, the heart rate value on the
information page will ash.
Caution: Improper battery replacement may lead to explosion. Please replace the battery with a
new one from device manufacturer or similar types set by it. Please dispose of waste batteries in
accordance with local regulations.
Please collect your waste batteries separated from other household garbage for easy
recycling and special treatment to protect our environment.