Gigabyte GA-8IRX User manual

GA-8IRXMotherboard
1
Table ofContent
BIOSSetup .......................................................................................................................2
The MainMenu (Forexample:BIOSVer.:F7) ..........................................................3
StandardCMOSFeatures..........................................................................................5
Advanced BIOSFeatures ..........................................................................................8
Integrated Peripherals.............................................................................................10
PowerManagementSetup.......................................................................................15
PnP/PCIConfigurations ...........................................................................................18
PCHealthStatus......................................................................................................19
Frequency/Voltage Control.......................................................................................21
Top Performance ......................................................................................................23
SelectLanguage ......................................................................................................24
Load Fail-SafeDefaults............................................................................................25
Load Optimized Defaults..........................................................................................26
SetSupervisor/UserPassword................................................................................27
Save&Exit Setup ....................................................................................................28
Exit WithoutSaving .................................................................................................29
Performance List............................................................................................................30
BlockDiagram................................................................................................................31
DualBIOS/Q-Flash Introduction.....................................................................................32
Fourspeaker&SPDIFIntroduction ...............................................................................40
@BIOSIntroduction ......................................................................................................44
EasyTuneIIITMIntroduction ............................................................................................45
DriverInstalling ...............................................................................................................46
BIOSFlash Procedure....................................................................................................50
Acronyms........................................................................................................................63
TechnicalSupport/RMASheet.....................................................................................65

GA-8IRXMotherboard
2
<?>Movetoprevious item
<?>Movetonextitem
<?>Movetothe iteminthe left hand
<?>Movetothe iteminthe righthand
<Esc> MainMenu -Quit and notsavechanges intoCMOSStatus Page Setup Menu and
Option Page Setup Menu -Exit currentpage and returntoMainMenu
<+/PgUp> Increase the numericvalue ormake changes
<-/PgDn> Decrease the numericvalue ormake changes
<F1> Generalhelp,onlyforStatus Page Setup Menu and Option Page Setup Menu
<F2> Reserved
<F3> Reserved
<F4> Reserved
<F5> Restorethe previous CMOSvalue fromCMOS,onlyforOption Page Setup Menu
<F6> Load the default CMOSvalue fromBIOSdefault table,onlyforOption Page Setup
Menu
<F7> Load the Setup Defaults
<F8> Reserved
<F9> Reserved
<F10> Saveall the CMOSchanges,onlyforMainMenu
BIOSSetup isan overviewofthe BIOSSetup Program.The programthatallowsuserstomodify
the basicsystemconfiguration.Thistype ofinformation isstored inbattery-backed CMOSRAMso
thatit retains the Setup information when the poweristurned off.
ENTERING SETUP
Afterpoweron the computer, pressing <Del>immediatelyduringPOST (PowerOnSelf Test)it will allowyouto
enterstandardBIOSCMOSSETUP.
If you requiremoreadvanced BIOSsettings,please go to“Advanced BIOS”setting menu.Toenter
Advanced BIOSsetting menu,press “Ctrl+F1”keyon the BIOSscreen.
CONTROLKEYS
BIOSSetup

TechnicalReference
3
?Standard CMOSFeatures
Thissetup page includes all the itemsinstandardcompatibleBIOS.
?Advanced BIOSFeatures
Thissetup page includes all the itemsofAwardspecialenhanced features.
GETTING HELP
MainMenu
The on-line description ofthe highlighted setup function isdisplayed atthe bottomofthe screen.
StatusPageSetupMenu /OptionPageSetupMenu
Press F1topop up asmall helpwindowthatdescribes the appropriatekeystouse and the possible
selections forthe highlighted item.Toexit the HelpWindowpress <Esc>.
TheMainMenu (For example:BIOSVer.:F7)
Once you enterAwardBIOSCMOSSetup Utility,the MainMenu (Figure1)will appearon the
screen.The MainMenu allowsyou toselectfromeightsetup functions and twoexit choices.Use
arrowkeystoselectamong the itemsand press <Enter>toacceptorenterthe sub-menu.
Figure1:MainMenu
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
?StandardCMOSFeatures SelectLanguage
?Advanced BIOSFeatures Load Fail-SafeDefaults
?IntegratedPeripherals Load Optimized Defaults
?PowerManagementSetup Load Top PerformanceDefaults
?PnP/PCIConfigurations SetSupervisorPassword
?PCHealthStatus SetUserPassword
?Frequency/VoltageControlSave&ExitSetup
TopPerformance ExitWithoutSaving
ESC:Quit F3:ChangeLanguage
F8:DualBIOS/Q-Flash F10:Save&Exit Setup
Time,Date,HardDiskType...

GA-8IRXMotherboard
4
?Integrated Peripherals
Thissetup page includes all onboardperipherals.
?Power ManagementSetup
Thissetup page includes all the itemsofGreen function features.
?PnP/PCIConfigurations
Thissetup page includes all the configurations ofPCI&PnPISA resources.
?PCHealthStatus
Thissetup page isthe SystemautodetectTemperature,voltage,fan,speed.
?Frequency/VoltageControl
Thissetup page iscontrolCPU’sclock and frequencyratio.
?Load Fail-SafeDefaults
Fail-SafeDefaultsindicates the value ofthe systemparameterswhich the systemwould
be insafeconfiguration.
?Load Optimized Defaults
Optimized Defaultsindicates the value ofthe systemparameterswhich the systemwould
be inbetterperformance configuration.
?Load Top Performance Defaults
Top Performance Defaultsindicates the value ofthe systemparameterswhich the system
wouldbe inbestperformance configuration.
?SetSupervisor password
Change,set,ordisablepassword.It allowsyou tolimit access tothe systemand Setup,
orjusttoSetup.
?SetUser password
Change,set,ordisablepassword.It allowsyou tolimit access tothe system.
?Save&Exit Setup
SaveCMOSvalue settings toCMOSand exit setup.
?Exit WithoutSaving
Abandon all CMOSvalue changes and exit setup.

TechnicalReference
5
Standard CMOSFeatures
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
StandardCMOSFeatures
Date(mm:dd:yy)Mon,Feb 21 2000 ItemHelp
Time(hh:mm:ss)22:31:24 MenuLevel
?IDEPrimaryMaster [PressEnterNone]
?IDEPrimarySlave[PressEnterNone]
?IDESecondaryMaster [PressEnterNone]
?IDESecondarySlave[PressEnterNone]
DriveA[1.44M,3.5”]
DriveB[None]
Floppy3Mode Support[Disabled]
Halt On[All,ButKeyboard]
BaseMemory640K
ExtendedMemory130048K
TotalMemory131072K
???? :MoveEnter:Select+/-/PU/PD:ValueF10:SaveESC:Exit F1:GeneralHelp
F3:Language F5:Previous Values F6:Fail-SafeDefaultsF7:Optimized Defaults
Figure2:StandardCMOSFeatures
?Date
The dateformatis<week>,<month>,<day>,<year>.
?Week Theweek,fromSun toSat,determined bythe BIOSandisdisplayonly
?MonthThemonth,Jan.ThroughDec.
?Day Theday,from1to31(orthe maximumallowed inthe month)
?YearTheyear, from1990 through2099
?Time
The times formatin<hour><minute> <second>.Thetimeiscalculated base on the 24-hourmilitary-
timeclock.Forexample,1p.m.is13:00:00.

GA-8IRXMotherboard
6
?IDEPrimary Master,Slave/Secondary Master,Slave
Thecategoryidentifies the typesofharddisk fromdriveCtoFthathas been installed inthe
computer.Therearetwotypes:autotype,and manualtype.Manualtype isuser-definable;Auto
type which willautomaticallydetectHDD type.
Notethatthe specifications ofyourdrivemustmatch withthedrivetable.The harddisk will notwork
properlyif you enterimproperinformationforthiscategory.
If youselectUserType,related information will be asked toentertothe following items.Enterthe
informationdirectlyfromthe keyboardand press<Enter>.Suchinformation shouldbe provided in
thedocumentation formyourharddisk vendororthe systemmanufacturer.
?Capcity:Theharddisk size.TheunitisMega Bytes.
?AccessMode:Theoptions are:Auto/Large /LBA /Normal.
?Cylinder: Thecylindernumberofharddisk.
?Head The read /Writeheadnumberofharddisk.
?PrecompThecylinernumberatwhich the disk driverchangesthe writecurrent.
?Landing Zone Thecylindernumberthatthe diskdriverheads(read/write)areseated whenthe
disk driveisparked.
?SECTORS Thesectornumberofeachtrack defineon theharddisk.
If aharddisk has notbeen installed selectNONEand press <Enter>.
?DriveA/DriveB
The categoryidentifies the types offloppydisk driveAordriveBthathas been installed inthe
computer.
?None Nofloppydriveinstalled
?360K,5.25in.5.25 inch PC-typestandarddrive;360Kbytecapacity.
?1.2M,5.25in.5.25 inch AT-typehigh-densitydrive;1.2Mbytecapacity
(3.5inchwhen 3Mode isEnabled).
?720K,3.5in.3.5inchdouble-sided drive;720Kbytecapacity
?1.44M,3.5in.3.5inchdouble-sideddrive;1.44Mbytecapacity.
?2.88M,3.5in.3.5inchdouble-sideddrive;2.88Mbytecapacity.
?Floppy 3Mode Support(for JapanArea)
?Disabled NormalFloppyDrive.(Default value)
?DriveAEnabled 3mode function ofDriveA.
?DriveBEnabled 3mode function ofDriveB.
?BothDriveA&Bare3mode FloppyDrives.

TechnicalReference
7
?Halt on
The categorydetermines whetherthe computerwill stop if an errorisdetected during powerup.
?NOErrorsThesystembootwill notstopforanyerrorthatmaybe detected
and you will beprompted.
?All ErrorsWheneverthe BIOSdetectsanon-fatalerrorthe systemwill be stopped.
?All,ButKeyboarThesystembootwill notstop forakeyboarderror; it will stopfor
all othererrors.(Defaultvalue)
?All,ButDisketteThesystembootwill notstop foradisk error; it will stop forall
othererrors.
?All,ButDisk/Key Thesystembootwill notstop forakeyboardordiskerror; it will
stop forall othererrors.
Memory
The categoryisdisplay-onlywhich isdetermined byPOST(PowerOnSelf Test)ofthe BIOS.
Base Memory
The POSTofthe BIOSwill determinethe amountofbase (orconventional)memory
installed inthe system.
The value ofthe base memoryistypically512 Kforsystemswith512 Kmemory
installed on the motherboard,or640 Kforsystemswith640 Kormorememory
installed on the motherboard.
Extended Memory
The BIOSdetermines howmuch extended memoryispresentduring the POST.
Thisisthe amountofmemorylocated above1MBinthe CPU’smemory
address map.

GA-8IRXMotherboard
8
Advanced BIOSFeatures
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
Advanced BIOSFeatures
FirstBootDevice [Floppy]ItemHelp
Second BootDevice [HDD-0]MenuLevel
ThirdBootDevice [CDROM]
BootUpFloppySeek [Disabled]
DRAMDataIntegrityMode Non-ECC
InitDisplayFirst[AGP]
???? :MoveEnter:Select+/-/PU/PD:ValueF10:SaveESC:Exit F1:GeneralHelp
F3:Language F5:Previous Values F6:Fail-SafeDefaultsF7:Optimized Defaults
Figure3:Advanced BIOSFeatures
?First/Second/Third Bootdevice
Thisfeatureallowsyou toselectthe bootdevice priority.
?Floppy Selectyourbootdevice prioritybyFloppy.
?LS120 Selectyourbootdevice prioritybyLS120.
?HDD-0~3 Selectyourbootdevice prioritybyHDD-0~3.
?SCSISelectyourbootdevice prioritybySCSI.
?CDROMSelectyourbootdeviceprioritybyCDROM.
?LANSelectyourbootdevice prioritybyLAN.
?USB-CDROMSelectyourbootdeviceprioritybyUSB-CDROM.
?USB-ZIP Selectyourbootdevice prioritybyUSB-ZIP.
?USB-FDD Selectyourbootdevice prioritybyUSB-FDD.
?USB-HDD Selectyourbootdevice prioritybyUSB-HDD.
?ZIP Selectyourbootdevice prioritybyZIP.
?Disabled Disabled thisfunction.

TechnicalReference
9
?BootUpFloppy Seek
During POST,BIOSwill determinethe floppydisk driveinstalled is40 or80 tracks.360 Ktype is40
tracks 720 K,1.2 Mand1.44 Mareall 80 tracks.
?Enabled BIOSsearches forfloppydiskdrivetodetermine it is40 or80 tracks.Note
thatBIOScan nottell from720 K,1.2 Mor1.44 Mdrivetype as theyare
all80tracks.
?Disabled BIOSwill notsearchforthe type offloppydisk drivebytrack number. Note
that therewill notbe anywarning message if the driveinstalled is360 K.
(Default value)
?DRAMDataIntegrityMode
Thisfeatureallowsyou tosetthe DRAMdataIntegrityMode
?Non-ECC Setthe DRAMdataIntegrityModeisNon-ECC (Default)
?ECC Setthe DRAMdataIntegrityModeisECC.
?Init Display First
Thisfeatureallowsyou toselectthe firstinitation ofthe monitordisplayfromwhich card,when
you install an AGPVGAcardand aPCIVGAcardon board.
?PCISetInit DisplayFirsttoPCISlot.
?AGP SetInit DisplayFirsttoAGP.(Default value)

GA-8IRXMotherboard
10
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
Integrated Peripherals
On-ChipPrimaryPCIIDE [Enabled]ItemHelp
On-ChipSecondaryPCIIDE [Enabled]MenuLevel
IDE1ConductorCable[Auto]
IDE2ConductorCable[Auto]
USB Controller [Enabled]
USB KeyboardSupport[Disabled]
USBMouse Support[Disabled]
OnboardH/WAudio[Enabled]
OnboardSerialPort1[3F8/IRQ4]
OnboardSerialPort2[2F8/IRQ3]
UARTMode Select[Normal]
?UR2DuplexMode Half
OnboardParallelPort[378/IRQ7]
ParallelPortMode [SPP]
?ECPMode UseDMA3
CIRPortAddress [Disabled]
?CIRPortIRQ 11
???? :MoveEnter:Select+/-/PU/PD:ValueF10:SaveESC:Exit F1:GeneralHelp
F3:Language F5:Previous Values F6:Fail-SafeDefaultsF7:Optimized Defaults
Integrated Peripherals
Figure4:Integrated Peripherals

TechnicalReference
11
?On-ChipPrimary PCIIDE
When enabled,allowsyou touse the onboardprimaryPCIIDE.If aharddisk controllercardis
used,setatDisabled.
?Enabled Enableonboard1stchannelIDE port.(Default value)
?Disabled Disableonboard1stchannelIDE port.
?On-ChipSecondary PCIIDE
When enabled,allowsyou touse the onboardsecondaryPCIIDE.If aharddisk controllercardis
used,setatDisabled.
?Enabled Enableonboard2nd channelIDE port.(Default value)
?Disabled Disableonboard2nd channelIDE port.
?IDE1 Conductor Cable
?AutoWill be automaticallydetected byBIOS(Default Value)
?ATA66/100 SetIDE1ConductorCabletoATA66/100(Please make sureyourIDE device and cable
iscompatiblewithATA66/100)
?ATA33 SetIDE1ConductorCabletoATA33 (Please makesureyourIDE device and cableis
compatiblewithATA33)
?IDE2 Conductor Cable
?AutoWill be automaticallydetected byBIOS(Default Value)
?ATA66/100 SetIDE2ConductorCabletoATA66/100(Please make sureyourIDE device and cable
iscompatiblewithATA66/100)
?ATA33 SetIDE2ConductorCabletoATA33 (Please makesureyourIDE device and cableis
compatiblewithATA33).
?USBController
Disablethisoption if you arenotusing the onboardUSB feature.
?Enabled EnabledUSB Controller. (Defaultvalue)
?Disabled Disabled USB Controller.

GA-8IRXMotherboard
12
.
?USBKeyboard Support
When aUSB keyboardisinstalled,please setatEnabled.
?Enabled Enabled USB KeyboardSupport.
?Disabled Disabled USB KeyboardSupport.(Default value)
?USBMouse Support
?Enabled Enabled USB Mouse Support.
?Disabled Disabled USB Mouse Support.(Default value)
?Onboard H/WAudio
?EnableEnableonboardsound function.(Default value)
?DisableDisableonboardsound function.
?Onboard SerialPort1
?AutoBIOSwill automaticallysetup the port1address.
?3F8/IRQ4EnableonboardSerialport1and address is3F8.(Default value)
?2F8/IRQ3EnableonboardSerialport1and address is2F8.
?3E8/IRQ4EnableonboardSerialport1and address is3E8.
?2E8/IRQ3EnableonboardSerialport1and address is2E8.
?Disabled DisableonboardSerialport1.
?Onboard SerialPort2
?AutoBIOSwill automaticallysetup the port2address.
?3F8/IRQ4EnableonboardSerialport2and address is3F8.
?2F8/IRQ3EnableonboardSerialport2and address is2F8.(Default Value)
?3E8/IRQ4EnableonboardSerialport2and address is3E8.
?2E8/IRQ3EnableonboardSerialport2and address is2E8.
?Disabled DisableonboardSerialport2.

TechnicalReference
13
?UARTMode Select
(Thisfeatureallowsyoutodetermine which InfraRed(IR)function ofOnboardI/Ochip)
?ASKIR Using as IRand settoASKIRMode.
?IrDA Usingas IRand settoIrDA Mode.
?NormalUsingas standardserialport.(Default Value)
?SCR Using as smartcardInterface.
?UR2Duplex Mode
Thisfeatureallowsyou toselecttheIRmodes.
?Half IRFunction DuplexHalf.(Default Value)
?Full IRFunctionDuplexFull.
?OnBoard Parallelport
Thisfeatureallowsyou toselectfromagiven setofparametersif the parallelportuses the
onboardI/Ocontroller.
?378/IRQ7EnableOnBoardLPT portand address is378.(Default Value)
?278/IRQ5EnableOnBoardLPT portand address is278.
?3BC/IRQ7EnableOnBoardLPT portand address is3BC.
?ParallelPortMode
Thisfeatureallowsyou toconnectwithan advanced printviathe portmode it supports.
?SPP Using Parallelportas StandardParallelPortusing IRQ7.(Default Value)
?EPP UsingParallelportas Enhanced ParallelPortIRQ5.
?ECPUsingParallelportasExtended Capabilities PortusingIRQ7.
?ECP+EPP Using Parallelportas ECP&EPP mode.

GA-8IRXMotherboard
14
?ECPMode Use DMA
Thisfeatureallowsyou toselectDirectMemoryAccess(DMA)channelif the ECPmode
selected.
?1SetECPmode use DMA1.
?3SetECPmodeuse DMA3.(Default value)
?CIRPortAddress
Thisfeatureallowsyou toselectCIRportaddress ordisableit.
?Disabled Disabled thisfunction.(DefaultValue)
?310 SetCIRPortAddress to310.
?320 SetCIRPortAddress to320.
?CIRPortIRQ
Thisfeatureallowsyou toselectCIRIRQ ,if CIRisenabled.
?5Set5forCIRPortIRQ.
?11 Set11 forCIRPortIRQ.(Default Value)

TechnicalReference
15
PowerManagementSetup
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
PowerManagementSetup
ACPISuspendType [S1(POS)] ItemHelp
Soft-Off byPWR-BTTN[Instant-off]MenuLevel
PMEEventWakeUp[Enabled]
ModemRingOn/WakeOnLan [Enabled]
ResumebyAlarm[Disabled]
?Date(ofMonth)AlarmEveryday
?Time(hh:mm:ss)Alarm0:0:0
PowerOnBy Mouse [Disabled]
PowerOnByKeyboard[Disabled]
?KBPowerOnPasswordEnter
ACBack Function [Soft-Off]
???? :MoveEnter:Select+/-/PU/PD:ValueF10:SaveESC:Exit F1:GeneralHelp
F3:Language F5:Previous Values F6:Fail-SafeDefaultsF7:Optimized Defaults
Figure5:PowerManagementSetup

GA-8IRXMotherboard
16
?ACPISuspendType
?S1/POS SetACPISuspend Type toS1/POS(PowerOnSuspend). (Default value)
?S3/STRSetACPISuspend TypetoS3/STR(Suspend ToRAM).
?Soft-off by PWR-BTTN
?Instant-off Presspowerbutton then Poweroff instantly.(Default value)
?Delay4Sec.Press powerbutton4sectoPoweroff.Entersuspendif button ispressedless
than4sec.
?PMEEventWakeup
When setatEnabled,anyPCI-PMeventawarkes the systemfromaPCI-PMcontrolled state.
?Disabled Disabled PMEEventWake up function.
?Enabled Enabled PMEEventWake up function.(Default Value)
?ModemRing On/WakeOnLAN
Anincoming call viamodemawakes the systemfromitssoft-off mode./When setatEnabled,an
inputsignalcomes fromthe otherclient/serveron the LANawarks the systemfromasoft off
stateif connected overLAN.
?Disabled Disabled ModemRingOn/Wake OnLANfunction.
?Enabled Enabled ModemRing On/Wake OnLANfunction.(Default Value)
?Resumeby Alarm
Youcan set"ResumebyAlarm"itemtoenabled andkeyinData/timetopoweron system.
?Disabled Disablethisfunction.(Default Value)
?Enabled Enablealarmfunction toPOWERON system.
IfRTCAlarmLead ToPowerOnisEnabled.
Date(ofMonth)Alarm:Everyday,1~31
Time(hh:mm:ss)Alarm: (0~23):(0~59):(0~59)

TechnicalReference
17
?Power OnByMouse
?Disabled Disabled thisfunction.(Defaultvalue)
?MouseClick Setmouse doubleclick topoweron system.
?Power OnByKeyboard
Thisfeatureallowsyou tosetthe method forpowering-on the system.
The option “Password“allowsyou tosetup to5alphanumericcharacterstopower-on the
system.
The option “AnyKey”allowsyou totouch the keyboardtopoweron the system.
The option “Keyboard98”allowsyou touse the standardkeyboard98 topoweron the system.
?PasswordEnterfrom1to5characterstosetthe KeyboardPowerOnPassword.
?Disabled Disabled thisfunction.(Defaultvalue)
?Keyboard98 Ifyourkeyboardhave“POWERKey”button,youcanpressthe keyto
poweronyoursystem.
?KB Power ONPassword
?EnterInputpassword(from1to5characters)and pressEntertosettheKey
boardPowerOnPassword..
?AC BackFunction
?Memory Systempoweron depends on the status beforeAClost.
?Soft-Off AlwaysinOff statewhen ACback.(Default value)
?Full-OnAlwayspoweronthesystemwhenACback.

GA-8IRXMotherboard
18
Figure6:PnP/PCIConfigurations
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
PnP/PCIConfigurations
PCI1/PCI5IRQ Assignment[Auto]ItemHelp
PCI2/PCI6IRQ Assignment[Auto]MenuLevel
PCI3IRQ Assignment[Auto]
PCI4IRQ Assignment[Auto]
???? :MoveEnter:Select+/-/PU/PD:ValueF10:SaveESC:Exit F1:GeneralHelp
F3:Language F5:Previous Values F6:Fail-SafeDefaultsF7:Optimized Defaults
PnP/PCIConfigurations
?PCI1/PCI5IRQAssignment
?AutoAutoassignIRQ toPCI1/PCI5.(Default value)
?3,4,5,7,9.,10,11,12,15 Set3,4,5,7,9,10,11,12,15 toPCI1/PCI5.
?PCI2/PCI6IRQAssignment
?AutoAutoassignIRQ toPCI2/PCI6.(Default value)
?3,4,5,7,9.,10,11,12,15 Set3,4,5,7,9,10,11,12,15 toPCI2/PCI6.
?PCI3IRQAssignment
?AutoAutoassign IRQ toPCI3.(Default value)
?3,4,5,7,9.,10,11,12,15 Set3,4,5,7,9,10,11,12,15 toPCI3.
?PCI4IRQAssignment
?AutoAutoassign IRQ toPCI4.(Default value)
?3,4,5,7,9.,10,11,12,15 Set3,4,5,7,9,10,11,12,15 toPCI4.

TechnicalReference
19
PCHealthStatus
Figure7:PCHealthStatus
CMOSSetupUtility-Copyright(C)1984-2002 AwardSoftware
PCHealthStatus
ResetCase Open Status [Disabled]
CaseOpened No
VCORE1.746VItemHelp
VCC18 1.792V
+3.3V3.296VMenuLevel
+5V5.080 V
+12V11.904V
CurrentCPUTemperature 39°C
CurrentCPUFANSpeed 4821RPM
CurrentPOWERFANSpeed 0RPM
CurrentSYSTEMFANspeed 0RPM
CPUWarning Temperature[Disabled]
CPUFANFail Warning [Disabled]
POWERFANFail Warning [Disabled]
SYSTEMFANFail Warning [Disabled]
???? :MoveEnter:Select+/-/PU/PD:ValueF10:SaveESC:Exit F1:GeneralHelp
F3:Language F5:Previous Values F6:Fail-SafeDefaultsF7:Optimized Defaults
?ResetCase OpenStatus
?Case Opened
If the case isclosed,"Case Opened"will show"No".
If the case havebeen opened,"Case Opened"will show"Yes".
If you wanttoreset"Case Opened"value,set"ResetCase Open Status"to
"Enabled"and saveCMOS,yourcomputerwill restart.
?CurrentVoltage(V)VCORE/VCC18/+5V/+12V
Detectsystem’svoltage status automatically.

GA-8IRXMotherboard
20
?CurrentCPU Temperature (°C)
DetectCPUTemp.automatically.
?CurrentCPU FAN /POWER/SYSTEMFAN Speed (RPM)
DetectFan speed status automatically.
?CPU Warning Temperature
?60°C/140°FMonitorCPUTemp.at60°C/140°F.
?70°C/158°FMonitorCPUTemp.at70°C/158°F.
?80°C/176°FMonitorCPUTemp.at80°C/176°F.
?90°C/194°FMonitorCPUTemp.at90°C/194°F.
?Disabled Don’tmonitorcurrenttemperature.(Default value)
?FanFail Warning (CPU /POWER/SYSTEM)
?Disabled Fan Fail AlarmFunction Disabled.(Default value)
?Enabled FanFail AlarmFunction Enabled.