Global Pool Products GPPSRT-GRAY-R User manual

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 1
www.global-poolproducts.com
RIP TIDE ASSEMBLY & INSTALLATION
GUIDE

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 2
RIP TIDE SLIDE
TABLE OF CONTENTS
Introduction PAGE 3
Rip Tide Post Installation Instructions PAGE 4
Maintenance Instructions PAGE 4
Rip Tide Slide Placement/Stub Up PAGE 5-8
Rip Tide Specification Sheets PAGE 9-11
Rip Tide Assembly PAGE 12-24
On Deck Mounting & Plumbing Instructions PAGE 25-28
Exploded View Reference Material PAGE 29-32

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 3
INTRODUCTION
Global Pool Products is located in Mid-Michigan. Global Pool Products prides itself in manufacturing top of the
line quality aquatic pool equipment and products. Global Pool Product’s key staff has a century of combined
industry experience and we take pride in each and every product that we build. Our products are made in the
United States. Global Pool Products uses only the finest materials and processes to provide our customers with
the highest quality products while still maintaining a price competitive edge.
The Rip Tide is designed for use on in-ground residential swimming pools ONLY. The Rip Tide Slide must be
properly assembled, installed, used and supervised for proper use and operation to reduce the risk of serious
injury and/or death.
Please refer to your local building codes and national building codes to be implemented prior to slide
installation.
Before starting assembly, remove all packaging and materials from the boxes. Double check to make sure that
nothing is left inside the boxes. Identify the parts and hardware utilizing the parts listed in this document.
Examine all parts thoroughly prior to installation to avoid anything that may have been damaged in transit.
A damaged part should not be used in the installation of this slide. Contact Global Pool Products if any parts
arrived damaged. Proper assembly and installation of the Rip Tide Slide is imperative. Not following the
directions provided will void Global Pool Products Warranty and may affect the safety of the slide rider.
After installation of the Rip Tide, please provide the slide owner with an owner’s manual, insist that warranty
information be completed and sent to Global Pool Products, discuss proper use of the slide, and answer any
and all questions regarding the safety of the slide.
NEGLECTING TO FOLLOW THESE INSTRUCTIONS AND THE OWNER’S
MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 4
POST INSTALLATION CHECKLIST FOR RIP TIDE SLIDE
Installer to review with slide owner upon completion of slide installation.
Examine:
฀The flume for any apparent cracks or gashes.
฀The ladder for sharp borders, snags, cracks, or gashes.
฀All fasteners to make sure none are loose.
฀The ladder for stability and connection to the flume.
✓Pool water depth at the base of the slide should be at least 3’ (914 mm) deep.
✓The height of the slide flume exit above the water should be 20” (508 mm) maximum.
✓The distance between the slide centerline and the edge of other pool equipment should be at
least 3’6” (1067 mm).
MAINTENANCE INSTRUCTIONS
A. Spray your Rip Tide Slide down with water to wash away build up.
B. Be sure that all connection points are tight. If not, tighten anchors as necessary.
C. All polyethylene parts require little maintenance. Hose and wipe to clean.
Examine:
฀The flume for any apparent cracks or gashes.
฀All fasteners to make sure none are loose.
฀The ladder and inner flume for sharp borders, snags, cracks, or gashes.

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 5
Rip Tide Slide Placement/Stub-up Location –Right Hand (Pivot 1)

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 6
Rip Tide Slide Placement/Stub-up Location –Left Hand (Pivot 1)

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 7
Rip Tide Slide Placement/Stub-up Location –Left Hand (Pivot 2)

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 8
Rip Tide Slide Placement/Stub-up Location –Right Hand (Pivot 2)

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 9
Rip Tide Slide Specifications
Product Numbers and Shipping Weights:
Model Number
Description
Shipping Weights
GPPSRT-GRAY-R
Rip Tide –Gray Granite Right
195 lbs (102 kg)
GPPSRT-SAND-R
Rip Tide –Sandstone Granite Right
195 lbs (102 kg)
GPPSRT-GRAY-L
Rip Tide –Gray Granite Left
195 lbs (102 kg)
GPPSRT-SAND-L
Rip Tide –Sandstone Granite Left
195 lbs (102 kg)
GPPSRT-GRAY-R-LED
Rip Tide –Gray Granite Right w/ Light Pkg
205 lbs (106.6 kg)
GPPSRT-SAND-R-LED
Rip Tide –Sandstone Granite Right w/ Light Pkg
205 lbs (106.6 kg)
GPPSRT-GRAY-L-LED
Rip Tide –Gray Granite Left w/ Light Pkg
205 lbs (106.6 kg)
GPPSRT-SAND-L-LED
Rip Tide –Sandstone Granite Left w/ Light Pkg
205 lbs (106.6 kg)
Broad Description:
The Rip Tide Slide is a sturdy, durable, roto-molded slide with enclosed plumbing for a clean
finished look. The Rip Tide is available in Sandstone or Gray Granite finishes and has the option
of an LED lighting package.
Utilization:
The Rip Tide is intended for use on in-ground residential swimming pools ONLY. Our multi point
anchoring system allows the Rip Tide to accommodate most geographical regions. The slide is
rated for a maximum of 275 lb. (124 kg) for its riders.
Specifications:
▪The ladder is enclosed with nine coping style steps for a safe and easy climbing.
▪The two handrails are roto-molded into the ladder with two optional widths for a comfortable
climb for most riders.
▪The slide runway has a twenty-one inch wide seating area made of a thick, durable,
roto-molded plastic.
▪The water delivery system is enclosed within the roto-molded ladder for a clean look.
Water is delivered with a 1” PVC hose to allow maximum water coverage on the flume
at 25 gpm.
▪The Rip Tide is anchored to the pool deck with ½” diameter galvanized anchor studs with
attaching hardware.

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 10
Rip Tide Slide Specifications

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 11
Rip Tide Slide Water Safety Envelope

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 12
RIP TIDE ASSEMBLY INSTRUCTIONS
Tools Needed:
1. 3/16” Allen Wrench 5. PTFE (Teflon) Tape 9. 5/8” Deep Well Socket
2. 7/32”Allen Wrench 6. PTFE (Teflon) Glue 10. 9/16” Deep Well Socket
3. 9/16” Wrench 7. PVC Primer 11. Ratchet
4. Anti-Seize (Included) 8. PVC Glue 12. Ratchet Extension
5. Phillips Head Screwdriver
Included Hardware:
(4) –3/8” Hex Bolt – 2” (34) –3/8” x 1” Washer (12) –Lock Washer
(4) –3/8” Button Head Bolt – 2” (10) –Concrete Anchors (2) –3/8” Acorn Nut
(2) –3/8” Button Head Bolt –3”(4) –3/8” Hex Bolt –4” (10) –Anchor Nut Caps
(2) –3/8” Hex Bolts – 3”(2) –3/8” Hex Bolt –3 ¾” (6) - #4 Screw x ½”
(10) –3/8” Nut (2) –3/8” Button Head Bolt –3 ½” (1) –Access Plate
(1) –54” Thick Foam-Rubber Gasket (2) –34” Foam-Rubber Gasket (2) –3/8” Hex Bolt – ¾”
(1) –7’6” PVC Flex Hose (1) –1” PVC MPT Adapter (2) –3/8” x 3” Studs
(1) –Roll of Butyl

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 13
Prior to the Start of Assembly:
oUtilize the cardboard that the slide shipped in as a barrier between your slide components
and the surface that the slide is being assembled on to prevent any scuffs and scratches.
oApply anti-seize to all threaded portions of the fastener hardware. This will aide in the
assembly, resistance of corrosion, and prevents galling.
oPrepare all bolts with a lock washer and washer in the order as shown below.
oTighten fasteners after all fasteners are threaded in place.
Scan the QR Code for Video
Assembly Instructions

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 14
Rip Tide Assembly Instructions
Attaching the base to the lower flume
a. Use bag one from the hardware kit to attach the lower flume to the base
b. Turn the lower flume upside down laying it on a soft surface to prevent scratches
c. Lay the base on the flume and attach them together using four 2”hex bolts using one flat washer
for each bolt
d. Once all bolts are started, tighten with a 9/16” socket
STEP 1

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 15
Installing the foam gasket and butyl on the lower flume
a. Measure the center of lower flume, use the two through bolt holes as measuring points, put a
mark with a sharpie low enough so it is not visible once the slide is assembled
b. Install one of the shorter 34” foam-rubber gasket from the seal kit tube on the lower flume, start
at the top and install it following the curve of the flume, cut off any excess and discard it
c. From the roll of butyl, cut a piece of butyl 28” long and mark the center with your thumbnail
d. Line the center of the lower flume to the center of the 28” long butyl (paper side facing you),
place it directly under the foam-rubber gasket following the curve of the lower flume, make sure
they are touching to ensure proper placement
e. Firmly press in the butyl to ensure it is secure to the flume, then remove the paper backing from
the butyl
STEP 2
Through bolt holes to find center.

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 16
Attaching the middle flume to the lower flume
a. Use two people to lift the middle flume and place it onto the lower flume, they lock into place with
the grooved design
b. From bag three in the hardware kit, use two 2” button head bolts, each with one flat washer on the
upper attachment points
c. From bag three in the hardware kit, use two 4” hex bolts, each with one flat washer on the lower
attachment points, secure them on the opposite side with a flat washer, then a lock washer, and
lastly a hex nut.
d. Plastic clamps may need to be used to aid alignment of the bolt holes
e. Once all bolts have been started, tighten the button head bolts with a 7/32” Allen wrench and hex
bolts and nuts with a 9/16” socket and 9/16” wrench
STEP 3

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 17
Installing a foam gasket and butyl to form the dual gasket on the middle flume
a. Measure the center of the middle flume, use the two through bolt holes as measuring points,
put a mark with a sharpie low enough so it is not visible once the slide is assembled
b. Install the second shorter 34” foam-rubber gasket from the seal kit tube on the lower flume,
start at the top and install it following the curve of the flume, cut off any excess and discard it
c. From the roll of butyl, cut a piece 28” long and mark the center with your thumbnail
d. Line the center of the middle flume to the center of the 28” long butyl (paper side facing you),
place it directly under the foam-rubber gasket following the curve of the lower flume, make sure
they are touching to ensure proper placement
e. Firmly press in the butyl to ensure it is secure to the flume, then remove the paper backing from
the butyl
STEP 4
Through bolt holes to find center.

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 18
Attaching the upper flume to the middle flume
a. Use two people to lift the upper flume and place it onto the middle flume, they lock into place
with the grooved design
b. From bag five in the hardware kit, use two 2” button head bolts, each with one flat washer on
the upper attachment points
c. From bag five in the hardware kit, use two 4” hex bolts, each with one flat washer on the lower
attachment points, secure them on the opposite side with a flat washer, then a lock washer, and
lastly a hex nut
d. Plastic clamps may be needed to aid alignment of the bolt holes
e. Once all the bolts have been started, tighten the button head bolts with a 7/32” Allen wrench
and hex bolts and nuts with a 9/16” socket and 9/16” wrench.
STEP 5

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 19
Attaching the plumbing
a. Use the PVC fitting in bag six from the hardware kit to hookup the plumbing in the upper ladder
b. Add PTFE (Teflon) tape and then PTFE (Teflon) glue to the to the 1” MPT Adapter to ensure the
plumbing doesn’t leak
c. Through the access hole located at the top of the upper ladder, thread fitting into the internal
brass fitting (molded into the upper ladder portion of the slide)
d. Apply PVC primer to the female end of the adapter and to one end of the flex hose
e. Starting with the primed end of the flex hose, route the flex hose through the upper ladder
portion of the slide, start at the hole located at the bottom of the upper ladder
f. Apply PVC glue to the female end of the adapter and the flex hose where it was primed
g. Join the flex hose with the PVC adapter (push in and twist for good adhesion) until the pipe
bottoms out, hold them together until they have started to bond
h. Allow for proper drying time before moving to the next step
STEP 6

“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry”
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606 Global Pool Products and not to be reproduced without
Fax: [phone] written consent from Global Pool Products.
www.global-poolproducts.com
Page | 20
Attaching the upper ladder to the lower ladder
a. Stand the lower ladder upright, place the upper ladder on top and guide the remaining flex hose
into the lower ladder
b. From bag seven in the hardware kit, use two 3” button head bolts each with one flat washer,
insert them into the handrail connection points from the front side, secure them on the opposite
side with a flat washer, then a lock washer, and lastly an acorn nut
c. From bag seven in the hardware kit, use two 3” hex bolts, place a lock washer then a flat washer
onto each bolt, insert them into the connection points on the back side of the ladder
d. Once all bolts have been started, tighten the button head bolts with a 7/32” Allen wrench, the
acorn nuts with a 5/8” wrench, and the hex bolts with a 9/16” socket.
STEP 7