GlobalTop HG-100 Operator's manual
HUDGPS
Quick Hardware Installation Rev.A03
GlobalTop Technology Inc.
16 Nan-ke 9th Rd Science-based Industrial Park, Tainan 741, Taiwan, R.O.C.
© Copyright 2006 GlobalTop Inc.
1.1 Package Contents
A) User Manual CD
B) Hardware Quick Installation Guide
C) Two pieces of Reflection layer film
D) Double side sticker
E) Iron Plate
F) HG-100 body
G) DC 5V Car Charger
1.2 Quick Hardware Installation
A. Paste the reflection layer film on windshield
NOTE:
Please be careful to complete the reflection layer film’s pasting in
the first time. Re-pasting of this reflection film will degrade the
efficiency of sticking.
1. Please find the most suitable position of the reflection layer
film on the windshield window to get the best projecting angle.
For example for left driving, it is recommended to put the
reflection layer film on the left under corner of the windshield
window.
2. Remove the backside film of the reflection layer film (item C)
and apply carefully into the chosen position on last step.
Gently smoothing this film onto windshield to eliminate and
avoid bubbling generated.
(Note：Regular process will be
recommended to apply one
slight thin film of soap mixed
water on the side which to stick
onto windshield)
3. After pasting the reflection
layer film (item C) on the
windshield window, adjust the
position to the suitable place.
4. Use the smooth slab to
remove the bubbles which stay
between reflection layer film
and windshield glass. Be
careful not to drag reflection
layer film out of chosen
position far away.
5. Wipe off the surplus soap water
around reflection layer film.
B. Fix the HG-100
1. Remove the backside paste of the double side sticker (item D)
and stick it onto the iron plate (item E) as shown below.
2. Place the iron plate on the dashboard and directly underneath
the reflection layer film. Check from driver seat if the image of
the iron plate is projected well into the area of the reflection
layer film. Mark this dashboard position as your reference
position.
3. Let HG-100 (item F) magnetize with the iron plate and check
the projecting area is right in the reflection layer film (item C)
and please make sure to get the most comfortable view angle.
4. Remove the other backside film of the double-side sticker
(item D) and paste on dashboard (which is decided in step 2).
C. Starting the HG-100
1. Starting your car and plug in the car charger to the HG-100.
2. Press the power button of the HG-100 last 2 seconds.
3. Put the HG-100 on the iron plate and it will be magnetically
fixed on the plate.
4. HG-100 will show “GPS” before got position fixed.
5. In the open sky, the HG-100 will get TTFF fixed within 1
minute.
6. After GPS position fixed, the HG-100 will project the heading
and speed of drive information.
HUDGPS
Quick Hardware Installation Rev.A03
GlobalTop Technology Inc.
16 Nan-ke 9th Rd Science-based Industrial Park, Tainan 741, Taiwan, R.O.C.
© Copyright 2006 GlobalTop Inc.
1.3 Speed Unit switch between km/h, mile/h
Press Function Touch button to switch km/h and mile/h.
1.4 Speed Warning Function
Press Function Touch button to set the speed warning.
1.5 HG-100 Button Function Setup
Power ON/OFF and Screen ON/OFF
Press 2 seconds Power ON and OFF
Power Button
Press 1 second When power on, HG-100 will switch on
and off the screen
Speed Unit Mode
Press 1 second HG-100 will into the speed unit mode.
Press0.5 second When in the speed unit mode, HG-100
will change the speed unit indicator.
Speed Warning Setting Mode
Press 2 seconds HG-100 will into the speed warning
setting mode.
Press 0.5 second When in the speed warning mode,
HG-100 will change the speed warning
setting.
Function Touch
Press 2 seconds When in the speed warning mode,
HG-100 will keep the setting and leave
the speed warning mode.
Function Touch button Function Touch button
S
p
eed Unit indicate
1 sec button pressed
HUD will show the setting of speed unit.
S
p
eed Warnin
g
indicate
2 sec button pressed
HUD will show the setting of speed warning.
Speed Warnin
g
Set
2 sec button pressed
HG-100 will keep the setting of Speed Warning.
Power Button
Function Touch
S
p
eed Unit Switch
0.5 sec button pressed
HUD will change km/h and mile/h every time.
Release button 3 seconds
HUD will keep the speed unit you choose.
S
p
eed Warnin
g
Switch
0.5 sec button pressed
HUD will change the setting of speed warning as a loop.
Other manuals for HG-100
1
Other GlobalTop GPS manuals
