Grandinroad 45478 User manual

# 45478 6’ Ultimate Animated Vampire

Parts List:

Assembly Instructions:

Note: You will need a Phillips Head Screwdriver (not included)

A B C D E F G H

NO P Q R

Base Shoes x 2 Support Poles

(upper have slots)

Hip hoop Chest hoop

(flat half

is front)

Jacket CapePants

HeadShoulder

support

Hat

Left arm Right arm Torso frame

with attached motor

A/C Adapter

STEP 1 STEP 2 STEP 3 STEP 4

Hands x 2

J K L

NOTE: The longer end of the (A) Base goes

towards the front.

First, slide (B) Shoes onto the (A) Base and then

assemble the (C) Support Poles through the tops

of the (A) Shoes as shown, with the slots

housings of the upper poles facing outward.

Insert (Q) screws through (C) Support Poles and

tighten to secure.

Lower (F) Pants over (C) Support Poles through

the leg openings & out through the top of the (F)

Pants. Attach the (D) Hip Hoop through the slots

on the upper (C) Support Poles as shown.

Assemble the (N) Torso Frame onto the (C) upper

Support Poles as shown and insert (Q) screws

and tighten to secure. Pull up the (F) Pants over

the (D) Hip Hoop and route the power cord

through and out the bottom of the right pant leg.

Attach the (E) Chest Hoop through the slots

located on the Torso Frame, with the larger part

of the (E) Chest Hoop in front. Attach the (O)

Shoulder Support as shown.

Lower the (G) Jacket down over the (N) Torso

Frame & (O) Shoulder Piece, and leave the back

of the (G) Jacket open.

Easy to Follow Instructions

Please read all instructions carefully before assembling.

Care & Storage Instructions: Store product in its original package. Keep away from heat & moisture. For indoor use only.

Save instruction sheet for future reference.

This item, when assembled by the following instructions, should take 15 minutes to assemble. Please follow the step

by step guide and enjoy your Ultimate Animated Vampire!

Moving Arm

Crossbar

!PROP 65 WARNING:

Handling the coated electrical wires of this product exposes you to lead, a chemical known to the State of California to cause cancer, birth defects or other reproductive harm.

Wash hands after use.

Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures; Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help.

Screws x 8

Cotter Pin x 4

A/C Adapter Specification:

Input: 120V~ 60Hz

Output: 6VDC 800mA

Only use adapter with same

technical specifications.

2011 0602

STEP 5

STEP 6

Slide the (L) Right Arm up through the right sleeve of the (G) Jacket and insert the forked-hook into

the right “shoulder” slot housing on the (N) Torso Frame. Connect the hooked end of the (M) Moving

Arm Cross Bar to the slot housing in the center of the forearm as shown, and then attach the other

end to the rotating shaft on the motor & secure both ends with included cotter pins.

Slide the (K) Left Arm up through the left sleeve of the (G) Jacket and insert the forked-hook into the

left “shoulder” slot housing on the (N) Torso Frame.

Next, set the (P) Head onto the (N) Torso Frame by sliding the forked-hook into the “neck” slot

housing. Carefully connect the connecting wire from the (P) Head to the connecting wire from the

motor. Now secure the costume & bowtie into place around the neck by fastening the hook & loop

closures at the back of the neck.

Set the right & left (J) Hands into place by sliding the forked-hooks into the “wrist” slot housings on

the ends of the Arms. Next, drape the (H) Cape over the back of the (G) Jacket and secure with the

hook & loop fasteners at the neck & at the palms of the (J) Hands. NOTE: The neck chain on the (H)

Cape has a removable elastic loop that fits around the right button for easier assembly. Place the (I)

Hat on the (P) Head.

Attach the (R) A/C Adaptor to the power cord routed through the right leg & plug into a standard outlet

to operate. When plugged into a standard outlet, motion, lights & sounds are activated by a

motion/light-activated sensor.

Sensor

NOTE: Sensors are Light activated & work best in brighter environments. TIP: For best results, position a light to shine at the sensor so that people will have to pass between the light source & the character – their

shadow will activate the functions of the character.