Greentel GT06 User manual

- 1 -
GREENTEL GPS Vehicle Tracker
Quick Guide
For GT06 Smart GPS Vehicle Tracker

- 2 -
1. Overview:
GT06
Accessory: power cable
Accessory: Relay
Accessory: Microphone
2. LED Indicators:

- 3 -
Red LED (power/working status)
LED Status Meaning
Flashing (interval 0.1s) Low battery indication
Continuously in bright state Charging
Slow Flashing (interval 0.2s) Full charge
Continuously in dark state Low battery/Power off
Slow Flashing (flash 0.1s after every 2s) Working normally
Blue LED (GPS status)
LED Status Meaning
Flashing (interval 0.1s) Searching GPS signal
Continuously in bright state GPS located
Continuously in dark state GPS not located
Green LED (GSM status indicator)
LED Status Meaning
Quick flashing GSM initialization
Slow Flashing (interval 0.2s) Receive GSM signal normally
Continuously in bright state GSM conversation/Start GPRS
Continuously in dark state No GSM signal
Ignition detection indication
Three (blue/red/green) LEDs are in cycling flashing.
3. Interface Introduction
4. Installation:
Preparation before installation:

- 4 -
A. Open the packing box to check whether the type of device is correct and whether the
accessories are included.
B. Please follow the following procedures to install your GT06. During installation, there
should be no power to the device.
C. Installing SIM card: each GT06 needs to insert a GSM SIM card. The SIM card should
activate GPRS service.
D. Testing SIM card: to test SIM card, please install it into a normal GSM mobile and
ensure it can send and receive SMS, and enables for GPRS.
E. Installing SIM card: remove the upper cover of device, insert SIM card as shown then
replace cover, lock the shell with 3 bolts.
F. Selecting installation place and fixing it. There are two kinds of installation: covert and
non covert. If you need the covert installation, please refer installation to an auto
electrical contractor.
Notice:
To prevent theft of the GT06, the device should be installed as covertly as possible.
Avoid placing the GT06 close to higher power electrical devices, such as reversing radar,
anti-theft device or other vehicle communication equipment;
The GT06 should be fixed into position with cable ties or wide double-side tape.
Your GT06 has built-in GSM antenna and GPS antenna. During installation, please make
sure the receiving side face is up, with no metal object above the device to interfere with
GPS reception.
The following places are suggested for installation:
- Under the dash board below the front windshield;
- In the parcel shelf in the rear;
- In the front bumper (non-material face), please ensure the device cannot get wet;
- Under the wiper version (non-metal), please ensure the device cannot get wet;
Notice: if the windshield is pasted with metal thermal-protective coating, it may affect the
performance of the device. In this case, please change the installation place after
consulting the professional.
G. Non Covert Installation,
Firstly fix the GT06 on the dash board below windshield
5. Device Wiring:
A. The standard voltage is 5V-36V, the red wire is the positive, and the black wire is the
negative.
B. Please connect the black wire to ground.
C. After connecting the power cord, run the power cord plug to the device. After
installation, supply power to device.
D. Covert installation: car battery cord is standard, with 2A FUSE for short-circuit over
current protection.

- 5 -
E. Non covert installation: cigar lighter cord is optional, with 2AFUSE for short-circuit over
current protection. Please contact your dealer if this mode is needed.
PIN Assignment
Line
No. Specification Color Instruction
1. 2 Keypod Orange/ orange Connect to SOS button
3. 4 MIC-,MIC+ Black/ red Connect to Microphone
5 TX Green Sending data (TX)/backup
6 RX White Receiving data (RX)/backup
7 GND Black Ground wire
8 MOTOR Yellow Connect to relay control line
9 ACC Orange Connect to ACC ignition
10 V- Black(thick) Vehicle 12V/24V negative storage battery
11 V+ Red(thick) Vehicle 12V/24V positive storage battery
Relay wiring notice:
The relay wiring of pump: Coil connectors of both ends are a thin white line (85) and a thin
yellow line (86). The thin white line (85) is connected to vehicle positive power (+12V). The
thin yellow line is connected to the device relay control line.
Cut off the positive connection line of the pump; then connect in series to the relay N.C.
contact (thick green line 87a) and the other end to relay COM contact ((thick green line 30).

- 6 -
Device wiring diagram
Cautions of device wiring
1. power/ACC/ Tele-cutoff (petrol/ electricity) control line (4 pin)
1.1 The standard voltage is 9V-36VDC. Please use the power line which provided by the
manufacture. The red line is the positive. The black line is the negative. The negative
should earth alone or link iron when installing. Do not connect to other ground wire.
1.2 ACC line (orange) is connected to the ACC switch of the vehicle. Please make sure to

- 7 -
connect the ACC line. The tracker will decide whether to enter ignition detection according
to ACC status. If do not connect toACC line, the device will enter ignition detection status.
If the vehicle vibrates when moving, it will activate the vibration alarm. If there is no need for
the theftproof function, connect theACC line to the positive in parallel and keep high level.
1.3 Tele-cutoff (petrol/ electricity) control line (yellow) is connected to pin 86 of the
Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of the relay socket).
2. USB cable (3 pin)
Firmware updating interface/expanded function to reserve space.
3. MIC line (2 pin)
External connect to microphone for voice monitor function
4. SOS line (2 pin)
Externally connect to SOS switch for SOS function.
6. Power On/Off:
A. The GT06 will power on automatically when connected to power. During normal
operation, red power LED flashes, while blue GPS LED and green GSM LED keep
lighting. During signal searching process, GPS or GSM LED will flash. If there is no
light presenting on LEDs, the device is not working normally.
B. The device will power on by battery after power is disconnected.
7. GPS Troubleshoot:
A. If GPS cannot receive the signals normally, please drive to the open areas for
positioning. Generally, it needs 1-2 minutes to receive the first coordinates. If the data
cannot be received after 2-3 minutes, please check the installation position of the
device, making sure it is not being shielded by any metal.
B. If GSM cannot receive the signals normally, please check whether SIM card is
installed correctly or there is no GSM signal at the location you are, such as a
basement parking, please drive to a place covered by GSM signal reception.
C. If the red LED does not work when power is connected, please check whether the fuse
is blown. If so, please replace the fuse.
D. If the three LEDs do not turn on when power up, press the down side key, if the three
LEDs recover normally, the device is working normally.
E. If you have enabled the web based tracking application, and the GT06 displays off-line
on the platform, please check 3 LEDs status indicators first. You can check the status
of the SIM card when you are in an inconvenient situation. Please refer to the following
steps:
1). Call the SIM card number of the device to check whether you can get through.
2). Check whether the SIM card supports GPRS and a localAPN.
3). Check the GSM/GPS reception area.
4). Check whether your SIM card charge is overdue.
5). Check if the connector and terminal is loose or the fuse has blown out.

- 8 -
8. GPRS Configuration via SMS:
GPRS Configurations (send configuration SMS to GT06):
SMS Content: GPRS,000000,APN,0,GT06.szdatacenter.com:8821,User
name,Password#
000000: GT06 default password
APN: APN of GSM operator
0: 0 or 1 optional, 0 stands for TCP communication, 1 stands for UDP communication
GT06.szdatacenter.com: internet domain name for the GPS server platform
:8821: server port
User name: dialup user name of GSM operator
Password: dialup password of GSM operator
#: ending symbol
After sending the SMS, the situation could be:
1）If you receive “Success”, go to web www.goosky.net to track the device.
2）If you receive “Fail”, it means that the device cannot identify the content of the SMS. In
this case, please check the content of SMS, especially the format of Minuscule/ Majuscule.
Find the problems and resend the SMS, you would get “success”.
3) If you cannot get any feedback after 5min, please check the device.
A Whether the indicating lights work orderly (The Green and Blue light should stay in solid
bright)
B If the Green light is not on solid bright, please check whether you insert the SIM card in
an appropriate way.
C If the green light is on solid bright already; please give a call to this SIM card to see
whether it could be called. If you have successfully make a call to this card, but you still
cannot track this device. Please also check whether the messages are full in this SIM card
(because the problem might be caused by the exceeding of SMS). Finally, you could track
this device.
Modification of password
SMS “XGYHMM, old password (6 digits), new password (6 digits)#”, The default password
is “000000”.
e.g.: XGYHMM,000000,123456#
Add specific number
The specific number is the SOS number. Three groups of specific numbers are available.
SMS command to the device to add specific numbers. In alarm status, the device will SMS
the location to the specific numbers, and it will call the specific numbers continuously until it
gets through.
Command format: ZJHM, user password, number#
e.g.: ZJHM,000000,136XXXXXXXX#
Reply information for successful setting:
Add the first group of specific number: “OK! Total number=1”

- 9 -
Add the second group of specific number: “OK! Total number=2”
Add the third group of specific number: “OK! Total number=3”
There are three group of specific number in maximum. If it receives “ERROR! ALREADY 3
NUMBERS”, it means you can not set any more.
Delete specific number
Before deleting specific number, please check its corresponding code. For the code,
please SMS “CXSZ, users’ passwords #” to the device.
Command format: SCHM, user password, code#
e.g.: SCHM,000000,1# ( it means deleting the specific number of code 1)
Note:
After deleting the specific number, the remaining two numbers will be adjusted
automatically with no skip code.
Reply information:
It will receive “Delete number 135XXXXXXXX success! specific number total 2” for
successful deleting of the specific number.
……
After delete the last group of specific number, it will receive: “Delete number
135XXXXXXXX success! specific number total 0”
When there is no specific number, it will receive: “Notice: Specific phone book empty!”
Check the parameter setting
SMS parameter setting command to the device to check the device setting.
Command format: CXSZ, users’ passwords #
e.g.: CXSZ,000000#
Reply information:
IMEI: 35341903XXXXXXX
GPRS time : 10
GPSOFF time: 20
SOS Number: 1. 135xxxxxxxx
2. 136xxxxxxxx
3. 137xxxxxxxx
Center Number:
Sensor time interval: 10
Sensor alarm time: 10
Time Zone: E: 8
It contains IMEI number/GPRS time/GPSOFF time/SOS number/Center number/Sensor
time interval/Sensor alarm time/Time Zone
GPRS time sending interval
The default GPRS time sending interval is 10s which means the device will upload
positioning data to the platform server every 10s. Users can modify GPRS time sending
interval by SMS “GPRSDS, password, time(second)#”. The time ranges from 10-18000s

- 10 -
For example: GPRSDS,000000,10#. It means the device will upload data to the server
every 10s
GPSOFF time
GPSOFF time is valid only in low-level ACC cable. When the vehicle power is off, dial the
device to activate it, and then the device will upload data to the server during the GPSOFF
time (default as 20mins). Users can modify GPSOFF time by SMS “GPSOFF, password,
time(minute)#”. The time ranges from 1-999mins
For example: GPSOFF,000000,20#. It means the device will work for 20mins after
activated
In addition, when ACC cable is in low level, the device will be activated to upload data by
trigger alarm
GPSOFF time is meaningless in high-level ACC cable. Once turn on the vehicle, GPS
keeps continuously working.
Sensor alarm time
When the vehicle power is off, the ACC cable is in low level. If the vehicle power keeps off
for 10 minutes, the device will come to the state of sensor alarm preparation automatically.
In that case, if several times of vibration happened, the device will trigger vibration alarm
mechanism. After that, if the vehicle power is still off (low-level ACC cable) in the following
3mins, the device will alarm instantly.
The sensor alarm preparation time can be modified by SMS
“SFDS,password,time(minitus)#” The time ranges from 1-180 mins.
For example: SFDS,000000,15#. It means when ACC cable is in low level for 15mins, then
the device comes to the state of sensor alarm preparation
Time zone
The time showed in the positioning data is defaulted as Beijing Time (Time zone is GMT+8).
If the device is in the place where the time is different from Beijing Time, users can modify
the time zone by SMS “SQSZ,password,director,code#”
For example: SQSZ,000000,W,11#. It means the time zone is GMT-11
E means East(GMT+), W means West(GMT-).
The code ranges from 0-12
View location method
By SMS
Send SMS “DWXX,password” to the SIM card number of the device to check its location.
The device will give a reply about the last positioning information. If it does not work, it will
reply ”NO DATA”
For example: SMS “DWXX,000000#”
Reply: Normal mode! Lat: 23d5.1708m, Lon: E114d23.6212m, Course: 120, Speed: 53.02,
Data Time: 10-04-12 14:52:36
By platform