Grundig GCT-K0123E User manual
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
camera parameters and functions.
2 MEGAPIXEL
FULL HD EYEBALL
HD-TVI CAMERA LED
User Manual
1 INTRODUCTION
1.1 Product Features
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology. It features high resolution,
low image distortion and low noise, etc., which
makes it suitable for surveillance system and
image processing system.
• High performance CMOS sensor and
high resolution bring high-quality image;
• Low illumination;
• Support auto white balance, auto gain control;
• Support image effect adjustment;
• Unit transmission control;
installation requirements.
1.2 Overview
2 INSTALLATION
Before you start:
• Please make sure that the device in the
package is in good condition and all the
assembly parts are included.
• Make sure that all the related equipment is
power-off during the installation.
installation environment.
• Check whether the power supply is matched
with your power output to avoid damage.
• Please make sure the wall is strong enough to
withstand three times the weight of the
camera and the mounting.
• If the wall is the cement wall, you need to
camera. If the wall is the wooden wall, you can
use self-tapping screw to secure the camera.
• If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Installation
Steps:
template.
supplied screws.
Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4. Secure the camera with the trim ring to the
mounting base.
HD Video Cable
Mounting e
Camera
Trim Ring re
Power Cable
Side Opening
Screw hole
Regulatory Information
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked
Products marked with this symbol
cannot be disposed of as unsorted
For proper recycling, return this product to
your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collecti-
www.recyclethis.info.
This product contains a battery that
cannot be disposed of as unsorted
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier
or to a designated collection point. For more informati-
FCC Information
and found to comply with the limits for a digital
limits are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful inter-
ference in which case the user will be required to
FCC Conditions
Rules. Operation is subject to the following two
received, including interference that may
cause undesired operation.
to get an optimum angle.
3 MENU OPERATION
select the menu and adjust the camera parameters.
3.1 Format
3.2 Setup
3.2.1 AE
image brightness by the BRIGHTNESS,
EXPOSURE MODE, and AGC.
Brightness:
Exposure Mode:
Move the cursor to Exposure Mode, you can select
Globe and BLC. When
AGC:
AGC optimizes the clarity of image in poor light
and HIGH.
3.2.2 WB
ATW and MWB in this menu.
ATW:
White balance is being adjusted automatically.
MWB:
Set the R GAIN/B GAIN
3.2.3 Day & Night
Move the cursor to DAY & NIGHT, and select
COLOR, B/W, or SMART as the DAY & NIGHT mode.
COLOR:
The image is colored in day mode all the time.
B/W:
The image is black & white all the time, and the IR
SMART:
3.2.4 Video Setting
Contrast:
Contrast enhances the difference in color and light
between parts of an image. You can set the value
Sharpness:
Sharpness determines the amount of detail that
an imaging system can reproduce. You can set the
Saturation:
You can set the saturation level of the image. The
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from
Mirror:
3.2.5 Reset
Reset all the settings to the default.
3.2.6 Exit
3.2.7 Save/Exit
NOTE
O
T
D
SMARTI R
CONTRAST
SATURATION
DNR
MIRROR
AGC
SS
POSU
L
C
TURN
C
MIDDL
MW
RG IAN
AI
N
T
SMART
N
SMART IR
