HansenCrafts miniSpinner Pro User manual

© 2016 HansenCrafts LLC April, 2016
miniSpinner ® Pro Manual
Welcome to the miniSpinner

Community! ................................................... 2
Unpacking Your miniSpinner

Pro................................................................ 2
miniSpinner

Pro Features............................................................................. 2
Safety Notes.................................................................................................... 2
Parts of the miniSpinner

Pro ........................................................................ 3
uick Start ..................................................................................................... 4
Set the direction of rotation.................................................................................4
Remote switch operation .....................................................................................4
Adjusting the Brake/Takeup – IM ORTANT! ..............................................4
Setting speed...........................................................................................................5
Flyer Instructions, Installation, and Maintenance ......................................... 5
Threading the Flyer and Moving the Yarn Guides..........................................5
Balance.....................................................................................................................5
Changing Bobbins .................................................................................................5
Drive Band and Brake Band................................................................................6
Flyer Installation ....................................................................................................6
Bobbins ...................................................................................................................6
Maintaining Your miniSpinner

..................................................................... 6
Lubrication..............................................................................................................6
Cleaning (Fuzz patrol) ..........................................................................................6
Problems? ....................................................................................................... 7
Error indicators......................................................................................................7
Motor stops, slows down or gets hot.................................................................7
Bobbin does not turn freely.................................................................................7
Flyer roblems .......................................................................................................7
Noisy Bobbin .........................................................................................................8
Brake Adjustment roblems................................................................................8
Yarn isn't being wound on the bobbin ..............................................................8
Take-up is too aggressive .....................................................................................8
Drive band breaks .................................................................................................8
Brake band breaks .................................................................................................8
Internal Brake Tension Cord Replacement ......................................................9
Remote switch stops working .............................................................................9
Optional Accessories and Resources.............................................................. 9
Orifice Reducers ....................................................................................................9
Orifice Threader ....................................................................................................9
Maintenance Kits ...................................................................................................9
Quill..........................................................................................................................9
Colored Bobbins....................................................................................................9
Batteries.................................................................................................................10
Spinning Books and More..................................................................................10

© 2016 HansenCrafts LLC April, 2016 2
Welcome to the miniSpinner

Community!
Thanks for buying a HansenCrafts miniSpinner ro. We think it’s the ultimate espinner!
Our goal at HansenCrafts is to create the most portable, quiet, and technically advanced electric spinners available. We've
spent a considerable amount of time on the design of both the mechanical components and the electronics.
The design has been refined over the years, and we intend to continue to develop and improve miniSpinners as we learn
more about the needs and wishes of those who use them. So, if you have a suggestion, please pass it on to us.
If you have any problems or questions whatsoever, LEASE contact us! Anything! We really mean it! We will do whatever it
takes to resolve any problems and to make you happy with your purchase.
If you purchase a miniSpinner and you are not completely satisfied, we will resolve any problem or you may return the
product for a refund within 60 days. Your satisfaction is very important to us.
Unpacking Your miniSpinner

Pro
miniSpinners are carefully packaged to withstand the usual shocks encountered
on the way to your door. If the box is damaged make note of it, and if possible
point it out to the shipper.
The box will contain several plastic bags protecting their contents. One bag will
contain your tote bag, paperwork, and accessories. The bag beneath that
contains your miniSpinner ro. Another bag contains the cord(s), power supply,
and remote switch.
Carefully inspect the items for signs of damage. If you notice any shipping
damage, save the packing materials and contact HansenCrafts for instructions.
We recommend you keep the packing materials for your miniSpinner Pro.
If you ever need to ship it, it will then have the best possible protection.
Note: When traveling with your miniSpinner Pro, protect the area around the speed control knob on the front
panel. The speed controller may be damaged if the face sustains an impact to the knob.
miniSpinner

Pro Features
Your miniSpinner ro uses a powerful, high-quality brushless DC (BLDC) motor. The absence of brushes ensures very long
life and quiet operation. The speed controller uses a very powerful ds IC30F4011 microcontroller to drive the motor and
monitor its operation.
The microcontroller software monitors motor R M and load and adjusts the power automatically to maintain constant speed,
regardless of load. It’s ideal for both production spinners (speed and power), as well as art yarn spinners (constant speed at
very low R M). It works just like the cruise control in your car!
Safety Notes
1. Disconnect the power from your miniSpinner ro when you leave it unattended. It is a powerful machine and
could be damaged (or cause injury) if turned on accidentally. We know of cases where a child or pet has
unintentionally turned on miniSpinners, which led to a few problems!
2. Your miniSpinner is not a toy; please keep small children at a safe distance when it is in use.
3. If you have the optional quill, please remove it when not in use.
4. Be sure to use the correct power supply with your miniSpinner ro; it must be 12 volts, and capable of supplying at
least 40 watts of power. Use of the wrong power supply can cause your miniSpinner to shut down unexpectedly,
overheat, and/or be damaged.

© 2016 HansenCrafts LLC April, 2016 3
Parts of the miniSpinner

Pro

© 2016 HansenCrafts LLC April, 2016 4
Quick Start
1. lace your miniSpinner ro on a flat, stable surface.
2. Connect 12 volt power to the jack on the left side of your miniSpinner. The LED/pushbutton will flash.
The color indicates direction; the number of flashes indicates the remote switch configuration:
Direction:  (Green) =  clockwise;  (Red) =  counterclockwise.
Remote:  One flash = "Deadman" mode (press and hold the remote switch down to stay ON).
 Two flashes = “Tap-Tap" mode (press the remote switch to turn ON, press it again to stop).
3. ress the LED/pushbutton to start your miniSpinner; turn the knob to adjust the speed.
4. ress the LED/pushbutton again to stop your miniSpinner.
Note: There is a two (2) second delay after power is applied before you can start spinning!
Set the direction of rotation
1. Press and hold the LED/pushbutton on the front of your miniSpinner.
2. The button changes color once per second while you hold the button: 
3. For  clockwise (spin direction) release the button when it is Green 
4. For  counterclockwise (ply direction) release the button when it is Red 
Your miniSpinner has a soft start feature; when you turn it on it gently accelerates to the desired speed so fine threads will
not break. miniSpinners also have a soft stop feature that slows the flyer at a controlled rate to minimize bobbin backlash.
Remote switch operation
The remote switch can operate in either of two modes:
1. Tap-tap mode: Useful for remote hand control; press the switch once to turn ON; press again to turn OFF. (You
can also use the LED/pushbutton to turn your miniSpinner on or off when in tap-tap mode.)
2. Deadman mode: ress and hold the remote switch to turn your miniSpinner ON; release it to turn it OFF. (Note:
The LED/pushbutton cannot be used to turn your miniSpinner on or off if the remote switch is plugged in.)
To configure the remote switch for Deadman mode
1. Unplug the power from your miniSpinner.
2. Be sure the remote switch is not plugged in.
3. Press and hold the LED/pushbutton on the front of your miniSpinner.
4. lug in the power (if you have a battery, it must be turned ON first).
5. Release the LED/pushbutton. It will flash once  or  to confirm you are in Deadman mode.
To configure the remote switch for Tap-Tap mode
1. Unplug the power from your miniSpinner.
2. Be sure the remote switch is plugged in.
3. Press and hold the LED/pushbutton on the front of your miniSpinner.
4. lug in the power (if you have a battery, it must be turned ON first).
5. Release the LED/pushbutton. It will flash twice  or  to confirm you are in Tap-Tap mode.
Note: All configuration settings are preserved, even when the power is turned off.
Adjusting the Brake/Takeup – IMPORTA T!
• Turn the wooden brake adjustment knob on the right side of your miniSpinner clockwise  to increase the
brake/takeup and counterclockwise  to decrease the brake/takeup.
• When properly adjusted the brake spring will be stretched very little, if at all, especially when plying.
• For best results, keep the brake setting at the minimum required to wind your thread onto the bobbin.
• Once you have the brake set so that the bobbin is just pulling in your yarn, adjust it only a tiny amount at a time
until you have a setting you're comfortable with. It is normal to readjust the brake as the bobbin fills.
• If you have to pull hard to keep your miniSpinner from taking up your yarn, if your miniSpinner stalls or warns that
it is overloaded, or if your yarn keeps breaking, reduce the brake/takeup.

© 2016 HansenCrafts LLC April, 2016 5
• There are springs on both ends of the brake band. The spring on the left is visible; the one on the right is inside the
miniSpinner. ull up on the swivel to feel that the internal spring is working.
• CAUTION: Do not completely relax the brake to the point that the spring
and/or brake band flops around loosely. The flyer arm may collide with the
loose brake band and break it.
• If you can’t adjust the brake, check to see if the swivel at the right end of
the brake band has been pulled down into the base and is stuck there!
• If the brake adjustment knob is difficult to turn or will not remain where
you have set it, adjust the friction on the knob. Adjust the setscrew in the
base of the spinner under the brake adjustment knob, as shown here:
Setting speed
Turn the knob next to the LED/pushbutton to set the speed. Your miniSpinner ro will go from 0 R M when rotated fully
counterclockwise to the 7:00 position, to about 2000 R M (3000 R M with lace flyer) when rotated fully clockwise to the
5:00 position.
The miniSpinner ro’s speed control will maintain the flyer speed you have set, even if the load varies. If your flyer begins to
slow down or speed up, the controller will automatically vary the power to maintain a constant speed, even at very low R M!
Most people spin with the speed set to between 9:00 to 12:00 on the speed knob. Adjust the speed to suit your ability
and keep it slow while you’re learning. Espinning is not about speed, it's about quality and control!
Flyer Instructions, Installation, an Maintenance
Threading the Flyer and Moving the Yarn Guides
repare the bobbin for spinning by threading its leader
through the moving eyelet on the right side of the flyer
arm, through the right-hand stationary eyelet at the
front of the flyer, then use the orifice threader to pull
the leader through the flyer orifice.
To move the yarn guides, you only need to apply gentle pressure
in the direction you want to move, as shown here. You don’t
need to squeeze it. Note that the ceramic eyelet is on the side
away from the orifice.
If the yarn guide doesn’t slide as easily as you’d like, remove it
and squeeze the yarn guide arms as shown. If it does not stay in place, spread the arms apart a
little. Apply paste wax to the carbon fiber arm occasionally to help the yarn guide slide freely.
Balance
You can move the unused yarn guide to balance your flyer, but do not remove it.
hanging Bobbins
To change bobbins, press the latch at the left rear corner, open the hinged back,
remove the brake band from the bobbin, and slide the bobbin off. To install the
bobbin, reverse the process.
You may have to align the spherical bearing at the rear so that the flyer shaft can
be inserted into it – wiggle the flyer shaft by lifting the bobbin core and note that
the spherical bearing will swivel (like an eyeball). The flyer shaft will go into the
bearing easily when it is aligned. Gently press the back towards the orifice end
until the latch clicks shut. Check that the bobbin rotates freely.
Last, place the brake band over the top of the bobbin in the groove.

© 2016 HansenCrafts LLC April, 2016 6
Drive Band and Brake Band
Use ONLY the clear drive band and long brake band with the HansenCrafts Jumbo flyer.
Use the black drive band and a short brake band with the HansenCrafts Lace Flyer. Never(!) use the black drive band with
the HansenCrafts Jumbo flyer because it is too short and will be overstretched.
For ease of switching between jumbo flyer and lace flyer, leave both brake bands attached. For video instruction on how to
have both brake bands attached go to: https://www.youtube.com/watch?v=5eMabTm7j3I
Flyer Installation
Smear a thin film of Super Lube

synthetic grease around the
outside of the orifice tube before installing the flyer. This
prevents it from “walking out” of the ball bearing, which can
cause a knocking noise once per revolution.
The flyer will slide into the ball bearing easily when correctly
aligned. Caution: If you force it, the flyer can get wedged into
the bearing and can be difficult to remove.
Note: You may need to adjust the latch for the correct endplay of about 1/16" (1mm) between the bobbin end and the rear
spherical bearing. Slightly loosen the screws holding the latch to the base of your miniSpinner, slide it to get the correct
amount of endplay, then tighten the screws. See http://hansencrafts.com/repairs/for detailed instructions.
Bobbins
All HansenCrafts bobbins are breakdown bobbins; you can disassemble them for
storage or for travel.
To assemble the bobbin, hold the end square to the bobbin core, apply gentle pressure,
and twist as shown. You will not be able to assemble or disassemble the bobbin unless
you twist the core a little bit.
Be sure the end is seated completely on the bobbin core so it can’t come apart!
Maintaining Your miniSpinner

Pro
Your miniSpinner ro was designed to be relatively maintenance-free. It is finished with
lacquer or wipe-on varnish; keep it clean with a dry, lint-free cloth.
• Keep your miniSpinner ro dry and avoid large, sudden temperature changes.
• You can use furniture polish on the wood if you like, but it isn't necessary.
Lubrication
Never oil any part of your miniSpinner Pro.
• The bearing at the orifice end is sealed and permanently lubricated.
• The bearing at the back end is self-lubricating plastic.
• The motor has permanently lubricated ball bearings.
leaning (Fuzz patrol)
Watch for fiber build up around the sheave and motor shaft. It is important to keep fiber from
accumulating around the shaft of the motor; see the photo. An excess of fiber in this area can
find its way into the motor’s ball bearing and damage it.
Do a daily inspection of the area around the motor shaft and remove any fiber. You can pick it
out with the pick from your Maintenance Kit or tweezers.
Never use compressed air because it can blow contaminants into the motor’s bearings.

© 2016 HansenCrafts LLC April, 2016 7
Problems?
Error indicators
The LED/pushbutton will blink if it detects an error; you can count the number of blinks to determine the type of error:
3 flashes (): Warning: Motor is operating at high load for this speed. (Excessive brake tension or drag).
4 flashes (): Motor turned off because it was overloaded for 3 minutes. See below.
5 flashes (): Motor turned off because it was stalled or lugging down due to excessive brake tension for the
speed you are using or some other source of drag.
6 flashes (): Input voltage < 10 volts (wrong power supply, external battery at wrong voltage or discharged).
7 flashes (): Input voltage > 15 volts (wrong power supply, external battery set at wrong voltage).
8 flashes (): Motor controller overheated due to excessively high loads for a prolonged period.
Motor stops, slows down or gets hot
Your miniSpinner ro is a precision machine, and when used properly will last a lifetime. It has plenty of power for normal
spinning and plying, but it is possible to overload it if you get carried away when plying, or if something is wrong. The speed
controller was designed to shut down if the motor is overloaded to prevent damage to the motor or the speed controller
circuitry. If this happens, the problem is usually excessive brake tension, though there are several possible causes.
Determine the cause and fix it before continuing. If you continue to operate your miniSpinner while it is grossly
overloaded you may damage it. Contact us for help!
• Brake tension is excessive. Excessive braking requires the motor to work harder. Adjust the brake so the fiber is
taken up at the desired rate; no more. Remember to loosen the brake after filling a bobbin.
• Something is causing the flyer or bobbin to bind. Remove the drive band from the motor sheave and rotate the
flyer by hand. If it does not rotate freely, figure out why it is binding and fix it. Occasionally this will only happen
when plying (counterclockwise). See “Flyer roblems” below.
• Check for fiber wrapped around the motor shaft. Unplug your miniSpinner, remove the drive band from the
sheave, and use the pick from your miniSpinner Maintenance Kit to gently remove any fiber from this area.
Bobbin does not turn freely
• Remove the brake band from the bobbin. The bobbin should rotate freely on the flyer shaft. It should have some
endplay; about 1/16” (1-2mm). If not, first check that the orifice end of the flyer is fully seated in the ball bearing.
If it isn’t, remove the flyer, apply Super Lube grease to the outside of the orifice tube, and reinstall the flyer.
• If there is no endplay, you may need to adjust the latch. Use a hillips screwdriver to loosen the screws holding the
latch to the base and slide the latch towards the rear. When properly adjusted, tighten the screws just enough so
that the latch does not slip. See http://hansencrafts.com/repairs/ for detailed instructions.
• If there is sufficient endplay but the bobbin is binding, remove the bobbin from the flyer shaft and check for fiber
build-up on the flyer shaft near the flyer or inside the bobbin itself.
• The hole in the bobbin may have become smaller than it should be. Contact HansenCrafts.
Flyer Problems
• Excess vibration; adjust unused yarn guide to balance the flyer. If one guide is removed, it will affect flyer balance.
• Knocking noise or flyer “walks out” of the ball bearing at the orifice end of your miniSpinner. Remove the flyer,
smear a thin coat of Super Lube grease on the outside of the orifice tube, and reinsert it into the ball bearing.
• If the yarn guide slips, be sure that the eye of the guide is on the side that's away from the orifice end. The yarn
guide will not stay in place if the eye is on the end of the guide closest to the orifice end of the flyer.

© 2016 HansenCrafts LLC April, 2016 8
Noisy Bobbin
• If the bobbin bounces back-and-forth or rattles, apply a little "blob" of
Super Lube grease to the orifice end of the bobbin and the far end of
the bobbin hole to act as a bumper to inhibit any tendency to bounce.
• Do not apply oil to the flyer shaft!
Brake Adjustment Problems
• If the brake action is too aggressive, use a soft lead pencil to draw a line in the bobbin brake groove. The graphite
from the pencil lubricates the brake groove and smoothes the brake action.
• If you are unable to tighten or loosen your brake – you may have turned the brake adjustment so far that it
pulled the swivel down into the base of your miniSpinner or the internal spring has been damaged. For more
information, see the Repairs section of the HansenCrafts website.
Yarn isn't being wound on the bobbin
• If the bobbin is empty, check to see that the leader is not slipping around the bobbin core. You can tighten it or
put a little tape over it to keep it from slipping.
• The brake band is not tight enough. If the brake spring is not stretched, adjust the tension a little tighter and try
again. For best results, use the minimum amount of brake tension that will draw in the yarn.
• Fiber from the yarn you are spinning may be caught on a yarn guide. Free the yarn from the yarn guide.
• Highly overspun yarn with coils in the singles will hang up on the yarn guides. Try spinning with less twist.
Take-up is too aggressive
• Brake tension is too tight. Loosen the brake, then tighten in small increments to the minimum needed to draw in
fiber when you want to wind onto the bobbin. Check to see if the swivel on the brake band is stuck in the hole in
the base. If it is, loosen the brake tension adjustment then pull the swivel out of the base.
• Use a soft lead pencil to draw a line in the bottom of the bobbin’s brake groove. The graphite lubricates the brake.
• When spinning a fine yarn, even minimal take-up can seem very strong. Consider adding our lace flyer, which is
specifically designed for fine spinning and very light takeup.
Drive band breaks
The polyurethane drive band used on the miniSpinner will generally last a very long time. If it should break, go to
http://www.hansencrafts.com to purchase a replacement.
• Do not use a rubber O-ring as a drive replacement, they are not designed for power transmission and will not last as
long nor perform as well as the original polyurethane belt supplied with your miniSpinner ro.
Brake band breaks
• The brake band has two parts. The external brake band is easily replaced. There is also an internal brake
band/spring assembly inside the base of your miniSpinner.
• The characteristics of the brake springs are critical to proper operation of your miniSpinner! Do not
replace the springs with just any spring; you will be disappointed with the result. You can purchase a complete
brake band assembly at http://www.hansencrafts.com
• Don’t spin with the brake band so loose that it flops around; if the flyer arm catches it, you could damage part of
the brake system, or even the flyer itself.
• To replace your brake band go to http://hansencrafts.com/repairs/ for detailed instructions.

© 2016 HansenCrafts LLC April, 2016 9
Internal Brake Tension Cord Replacement
Internal brake tension cords are available from HansenCrafts. If you should need to replace the braided line inside the
spinner go to http://hansencrafts.com/repairs/.
Remote switch stops working
The cord has probably been damaged. This typically happens because someone tripped over the
cord, the cord has been sharply flexed too often, or a pet chewed on it.
The remote switch cable was chosen because it is very flexible. The drawback is that it is
susceptible to damage if abused; it's just one of those tradeoffs made in product design. It is
important to handle it with care.
• Only disconnect it by the pulling the plug, not by pulling on the cord itself.
• Do not store the miniSpinner in a case or bag with the cord plugged in.
• Gently wrap the cord when not in use as seen in picture to the right.
Optional Accessories an Resources
You will find an active and vibrant HansenCrafts miniSpinner group online, on the Ravelry social network, with many
suggestions for aftermarket accessories and spinning advice. Membership in Ravelry is free, and allows you to see the group
and participate as well. Visit the group at: http://www.ravelry.com/groups/hansencrafts-minispinner
Orifice Reducers
We produce these in three sizes, 1/8”, ¼”, or 3/8 ” so you can select the optimal orifice size for the
diameter of the thread you're spinning. These stabilize your thread and prevent the thread from oscillating
by bouncing around in an excessively large orifice. They're essential for spinning fine yarns!
Orifice Threader
It is a great idea to have a spare orifice threader. These are made by us of glass beads and monofilament
line and available on our website.
Maintenance Kits
The miniSpinner Maintenance Kit includes spares, Super Lube grease, and a tool for
cleaning and maintaining your miniSpinner.
Quill
How about an inexpensive electric bobbin winder? Our ¼”/6.5mm quill works well as a bobbin
winder for inexpensive storage bobbins or weaving bobbins, thereby making your miniSpinner
ro into an electric bobbin winder! Note: 6.5mm is slightly larger than the 1/4" hole in
HansenCrafts bobbins so they cannot be used with the quill as a bobbin winder for
HansenCrafts bobbins. The ideal storage bobbins are inexpensive paper bobbins, plastic
weaving bobbins, or pirns.
olored Bobbins
Just for fun, why not consider colored bobbins?

© 2016 HansenCrafts LLC April, 2016 10
Batteries
Battery packs make miniSpinners truly portable, and many owners have them. Battery packs are ideal for spinning in
airplanes, campers, and outdoor venues. It's wonderful to be independent of cords!
Hundreds of different models of battery are available, but not all are suitable for powering a miniSpinner ro.
Recommended specifications for battery packs:
• 12 volt output; no more, no less.
• Ability to deliver up to 3.5 amps of current at 12 volts.
• Capacity of at least 20,000 mAh (milliamp-hours), or 20 amp-hours. This will easily power a miniSpinner ro for a
long day of spinning. A higher capacity will give more spinning time.
• ower connector: 5.5mm x 2.1mm plug
HansenCrafts does not sell batteries but you can go to http://hansencrafts.com/batteries/ for links to Amazon for batteries
that work with miniSpinners.
Spinning Books and More
We recommend the following books;
The Intentional Spinner by Judith MacKenzie
The Spinners Book of Yarn Design by Sarah Anderson
ower Spinning – An ebook on espinning by Amelia Garripoli available for download at http://hansencrafts.com/power-
spinning-by-ameila-garripoli-e-book/
Check your local area for guilds or at your local yarn shop for spinning groups. Spread the “love”!
Warranty
miniSpinners are warranted against defects for life to the original owner. We expect that you will maintain your miniSpinner according to the
instructions, and not abuse it. We provide outstanding product support to all miniSpinner owners.
HansenCrafts LLC
710 East Park Avenue
Port Townsend, WA 98368
U A
(360) 747- PIN (7746)
[e-mail]
www.hansencrafts.com
"miniSpinner" is a registered trademark belonging to HansenCrafts LLC.
The miniSpinner asymmetric cresting wave design of the face and back is copyright© 2009-2016, HansenCrafts LLC.