Harman Modero S Series User manual

QUICK START GUIDE
MSA-AMK-07/10 Modero S Series® Any Mount Kit
MSA-AMK-07/10
The MSA-AMK-07 and MSA-AMK-10 Any Mount Kits are designed to mount 7"or 10”
Modero S Series Wall Mount Touch Panels into standard single or double gang boxes in
the US, UK, EU and Australia, making the installation of a Modero S Series control
interface simple and effective. The MSA-AMK-07 (FG2265-25) is compatible with the
MSD-701 (FG2265-02), while the MSA-AMK-10 (FG2265-26) (FIG. 1) is compatible
with MSD-1001 (FG2265-01).
Installation of the Any Mount Kit
The Any Mount Kits are designed to utilize existing or newly installed gang boxes, with a
new back box to replace the back box included with the touch panel. To install an Any
Mount Kit and its accompanying touch panel:
1. Before starting the installation, ensure that Ethernet cable has been pulled to the
gang box, and that all appropriate Power Over Ethernet (PoE) injectors have been
connected to the cable going to the gang box.
2. If the gang box already has an existing fixture or device installed in it, remove the
fixture or device to expose the gang box (FIG. 2).
3. Pull the Ethernet cable into the gang box, making sure that the male RJ-45
connector is accessible within the gang box.
4. Match the screw connector holes on the gang box with the holes in the back box
(FIG. 3). The Any Mount Kit back box has multiple holes to allow for single or
double gang box design, and for standard gang box designs from the US, UK, EU
and Australia. At the same time, examine how the back box rests on the gang box,
looking for gaps between the back box and the wall surface.
5. If the gap between the wall and the back box is extreme, or if the installation of
the back box exposes too much of the gang box, you may apply the optional foam
gasket (MSA-AMK-07: 66-2265-29; MSA-AMK-10: 66-2265-30) to the back of the
back box. Peel the adhesive backing off the gasket and carefully apply it to the
back box surface (FIG. 4).
6. Once you have confirmed the proper mounting position of the back box, attach
the back box to the gang box, using either the screws used with the original
fixture or device or with the included screws in the Any Mount Kit (FIG. 5).
WARNING: Be careful not to over-tighten the screws, which can bow or damage the
back box.
7. After installing the back box, inspect the back box’s placement. If necessary, the
back box can be removed and the foam gasket installed.
FIG. 1 MSA-AMK-10 ANY MOUNT KIT BACK BOX (REAR)
PRODUCT SPECIF ICATIONS
Models Available: • MSA-AMK-07 (FG2265-25)
• MSA-AMK-10 (FG2265-26)
Dimensions (HWD): • MSA-AMK-07: 4.88” x 7.38” x 0.98”
(12.4 cm x 18.8 cm x 2.5 cm)
•MSA-AMK-10: 6.53” x 9.76” x 0.98”
(16.6 cm x 24.8 cm x 2.5 cm)
Weight: • MSA-AMK-07: 0.10 lbs (45.36 g)
•MSA-AMK-10: 0.25 lbs (113.40 g)
Certifications: TBD
Included Accessories: MSA-AMK-07:
•BackBox(60-2265-33)
•Gasket,Foam(66-2265-29)
• Screw, M3.5 X 30mm, PFH, Clear Zinc (4) (80-1620-04)
• Screw, #6-32 X 1.25, PFH, Type F, Clear Zinc (4) (80-1700-09)
MSA-AMK-10:
•BackBox(60-2265-34)
•Gasket,Foam(66-2265-30)
• Screw, M3.5 X 30mm, PFH, Clear Zinc (4) (80-1620-04)
• Screw, #6-32 X 1.25, PFH, Type F, Clear Zinc (4) (80-1700-09)
Other AMX Equipment: • MSD-701 7” Modero S Series Wall Mount Touch Panel
(FG2265-02)
• MSD-1001 10” Modero S Series Wall Mount Touch Panel
(FG2265-26)
FIG. 2 EXISTING GANG BOX
Gang Box
Wall surface
FIG. 3 TESTING THE ALIGNMENT OF THE BACK BOX SCREW HOLES.
FIG. 4 APPLYING THE OPTIONAL FOAM GASKET TO THE BACK BOX.
FIG. 5 INSTALLING THE BACK BOX TO THE GANG BOX.
Gasket
Adhesive backing

© 2015 Harman. All rights reserved. Modero, AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks of
HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective
companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax [phone]
AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • [phone] • www.amx.com/eu/
93-2265-25 REV: C
Last Revised: 8/12/2015
8. Pull enough slack on the Ethernet cable through the back box to allow the cable to
reach the touch panel’s RJ45 connector (FIG. 6).
9. Remove the touch panel’s back box to access the back of the panel.
10. Insert each connector into its corresponding location along the back of the touch
panel. For more information on connection, please refer to the Operation
Reference Guide for the Modero S Series panel being installed, available from
www.amx.com.
11. Test the incoming wiring by attaching the panel connections to their terminal
locations and applying power. Verify that the panel is receiving power and
functioning properly to prevent repetition of the installation.
12. Latch the panel onto the top hooks on the back box and rotate it down (FIG. 7).
13. Press gently but firmly and evenly on the surface of the touch panel until the top
panel snap “clicks” to lock it down (FIG. 8).
WARNING: if you see a gap between the panel and the back box, or feel any binding
while locking down the panel, stop immediately and verify that no cables or other
items are in the way. Do not force the panel into position, as this can cause damage to
the touch screen or the panel electronics.
Removing the Touch Panel
In order to access the back of the touch panel, such as to install a USB connection for
firmware upgrades, the device may need to be removed from the back box. To remove
the touch panel:
1. From the bottom, pull gently outward from the back box. Gently rock the panel
back and forth to free the bottom from the back box.
2. Rotate it up to release the top latch hooks, and carefully pull the device free from
the back box. Take care not to damage or pull the connections on the back of the
device, or to pull the back box from the gang box.
FIG. 6 ACCESSING THE ETHERNET CABLE THROUGH THE BACK BOX.
FIG. 7 HOOKING THE TOP OF THE TOUCH PANEL ON THE BACK BOX.
Pull Ethernet cable
through back box
Top hooks
FIG. 8 LOCKING DOWN THE BOTTOM OF THE TOUCH PANEL ONTO THE BACK BOX.