HAT SX2 User manual

11. Hardware Bag x1
Page: 1 of 5
SX2 Wall Mount
10. Network Cable x2
9. 120v Power Cord x1
8. Control switch x1
7. Control box x1
6. 28.3" Rear Crossbarx1
5. Top-beam Short x2
4. Top-beam Long x2
3. SX Leg x2
2. Front Shroud - Wall mount bracket x2
1. Rear - Wall mount bracketx2
Components Required:
this electrically height adjustable mechanism.
Assembly Steps:
1. Before installing your new SX2 wall mount unit,
determine the wall type and locations of wood or metal
studs, wall cavities, and wall reinforcements. Only install
into a reinforced section of wall that can support 600 lbs.
of load.
2. Using the rear wall mount bracket(1) and a level, mark
the six mount positions for each bracket in the wall;
twelve wall mount positions per complete assembly.
Ensure each mount is completely level before marking.
There should be a 1/2" gap between the floor and
bottom of the rear wall mount bracket (1)(Fig 1).
NOTE:Make sure that the red circle is positioned at the
top of the wall mount bracket(1) when aligning(Fig.1).
3. After marking the mount holes for the first rear wall
mount bracket(1), use a laser level and a tape measure
to mark the mount holes for the second mount bracket
(1). Ensure the mount holes are completely level up and
down, left to right before drilling pilot holes(Fig.1)
Warning: If the fully installed mounts are not properly
aligned it will cause binding and immediate failure of
FRONT ELEVATION VIEW - WALL PREPARATION - Fig.1
1
FLOOR LEVEL
(12)x MOUNT HOLES
ENSURE MOUNTS ARE LEVEL
LEFT TO RIGHT
1
RED CIRCLE
8.66in
220mm
43mm
1.69in
43mm
1.69in
8.66in
220mm
mount bracket (1)
Back edge of Rear wall
FLOOR LEVEL
© 2022 Human Active Technology, LLC P516159 REV B
Human Active Technology
800 524 2744
[e-mail]
team-hat.com

45
2
2
6
3
3
4
5
2xA
2xA
2xA
Page: 2 of 5
2xA
2xA
2xA
2xA
R011074
Tools required: Drill driver, PHILIPS bit PH1 and PH2. Hex key 4mm.
A x 20 (m6x12)
2xA
SX2 Wall Mount
4. Select wall mounting hardware for use in the
applicable wall type. Contact SIS Ergo for
recommendations of use. 1.800.374.7438 #2007.
5. Once wall mount hardware is selected, use the
marked hole locations and drill pilot holes
corresponding to the hardware and wall type in
use.
6. Attach rear wall mount brackets(1) to the
reinforced wall section using selected hardware
and pilot holes.
NOTE: Ensure rear wall mount brackets are leveled
and properly spaced per (Fig.1) before
proceeding. Adjust accordingly.
Frame Assembly
7. Attach one top-beam long(4) to the inside face
of each leg(3) using two m6x12 bolts(A).
8. Attach one top-beam short(5) to the outside
face of each leg(3) using two m6x12 bolts(A).
9. Attach the rear crossbar(6) to the back of each
leg(3) with two m6x12(A) bolts per leg(3), four
m6x12mm(A) bolts total.
10. Attach one front-shroud wall mount bracket(2)
to each leg(3) with four m6x12 bolts(A), eight
m6x12mm(A) bolts total.

2 x E
R011500
Page: 3 of 5
R011501
C x 2 (4x16mm)
R011528
B x 19 (5x20mm)
the control box(7).
16. Connect control switch cable(8) to port A1 in
19 x B
11. Attach assembled base frame to work surface
using nineteen 5x20mm wood screws(B).
12. Connect power cable(9) to the control box(7),
and rout the power cord thru the horseshoe
channel next to the power cable plug connection
on the underneath of the control box(7) (Fig.2).
13. Attach control box(7) to underside of
worksurface using two 4x50mm screws(E).
14. Connect a network cable(10) to the control
box(7) and then to each leg(3).
15. Attach control switch(8) to underside of
worksurface using two 4x16m screws(C).
E x 2 (4x50mm)
2 x C
SX2 Wall Mount

FLOOR LEVEL
REINFORCED WALL SECTION
4 x F
completely finished before normal operation.
R011063
reset and make sure the procedure has
Page: 5 of 5
18. Screw two m8x16mm screws(F) into each side
of the rear wall mount brackets(1), eight total in the
complete assembly. Only screw the bolts in half
way. Do not fully tighten until the frame is fully
mounted.
19. Using two people, lift the assembled frame onto
the rear wall mount bracket(1) so that the front
shrouds(2) lock onto the m8x16mm bolts(F).
NOTE: Once mounted the table legs(3) should not
feel like they are being torqued in or out, and the
assembly should be level.
Warning: If the legs are being heavily torqued into
the rear wall mounts(1) this will cause the
mechanism to bind and fail. Remove the assembly
from the wall, make slight adjustments to the frame
as needed, retighten, and reinstall.
Once the frame is mounted and leveled fully
tighten the m8x16mm bolts(F) to lock in place.
20. Plug in the 120v power cord(9) into an
appropriate 110V wall receptacle.
21. Perform initial reset by pushing the down-button
until the table stops. Push the down-button again
and "hold it" until the legs stop moving.
22. The power cord(9) should be restrained to
ensure no excess slack when the mechanism is
adjusted to its highest point, and should not be
over stretched causing the cord to pull out of the
wall receptacle.
Troubleshooting:Make sure that all cables are
correctly connected to the control box, legs,
control switch, and power source. Perform a new
F x 8 (m8x16mm)
4 x F
SX2 Wall Mount
1
1