HCP UFP Series User manual

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
HCP Technology
UFP Series
User Manual

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
2
Table of Contents
Part 1 Safety Information…………………………………………………………………3
Part 2 Install the LED Screen
1. Overview………………………………………………………………………………………5
1.1 Components……………………………………………………………………………5
1.2 Tools………………………………………………………………………………………..5
2. Install the Wall Mount Rack…………………………………………………………..6
2.1 Install the horizontal rails…………………………………………………………6
2.2 Install the vertical rails……………………………………………………………..6
2.3 Install the lower rail………………………………………………………………….7
3. Install the LED Cabinets Frame………………………………………………………8
3.1 Install the shrapnel nuts and cabinet connection Plates……………8
3.2 Install the cabinet frames…………………………………………………………11
4. Connect the cables………………………………………………………………………..13
5. Install the LED display screen…………………………………………………………14
Part 3 Trouble Shooting……………………………………………………………………..16

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
3
Safety Information
Warning！
A warning for a potentially hazardous situation that can result in
death, personal injury, or property damage if not adhered to.
Caution！
A recommendation for a potentially hazardous situation that
may result in personal injury or property damage if not adhered
to.
Warning！
Risk of electric shock or fire due to high-voltage components.
※Do not expose this unit to rain or moisture.
※Do not submerge this unit partially, or completely in water, or
liquids.
※Do not use this unit's polarized plug with an extension cord
receptacle or other outlets unless the prongs can be fully
inserted.
※Do not open the cabinet because of the high-voltage
components inside. There are no user-serviceable parts are
inside.
※Only qualified service personnel are allowed to service and
open the unit.
Risk of electric shock.
※If not in use, fully disengage the power to the unit by
disconnecting the power cord from the AC outlet.
※Do not use damaged cables. Check cables regularly. Replace
damaged cables immediately, they are not user-serviceable.
※Ensure the system is properly grounded.
Risk of overload of the power cable.
To protect the power cable against overload maximum 16
cabinets shall be wired in a row at 100 V AC or 38 cabinets at
240 V AC. The total load must not exceed 16 A per cable.
Risk of fire, injuries and product damage.
※Keep the system away from flammable material.
※Never block the air ventilation spaces around the LED Wall.
Keep them free at all times.
※Only use the supplied cables, which are fit for the system and
its components.

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
4
Risk of product damage due to dusty environment.
※Do not install or operate the system in a dusty environment.
Risk of product damage by moisture or water.
※Do not clean the system with water. Do not wipe the LED
Panel with a damp cloth.

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
5
UFP Series-User Manual
1.Overview
1.1 Components
1.2 Tools
Shrapnel nut Rack Connection Plate Cabinet Connection Plate
M8 30*40mm 90*90mm
Hex Socket Head Screws Hex Socket Head Screws Hex Socket Head Screws
M6*6 M8*12 M8*20
1
2
Cordless Hammer Drill Allen Key Phillips Screwdriver
M5&M6
Tape Measure Spirit Level Vacuum Suction Tool

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
6
2. Install the Wall Mount Rack
2.1 Install the horizontal rails, please ensure the horizontal rails are in the same
levels. The spirit level shall help to adjust the rails and then use the Allen Key for
locking the screws.
WALL
LED Display Screen
3. M8*12 Screws
2. Rack Connection Plate 1
1. Shrapnel nuts

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
7
2.2 Install the vertical rails in the same manner as horizontal rails.
3. M8*12 Screws
1. Shrapnel nut
2. Rack Connection Plate 2

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
8
2.3 Install the lower rails in the same manner as horizontal rails.
W A L L
2. Rack Connection Plate 2
1. Shrapnel nut
3. M8*12 Screw

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
9
3. Install the LED Cabinets Frame
3.1 Install shrapnel nuts and cabinet connection Plates
3. M8*12 Screws
2. Cabinet Connection Plate
1. shrapnel nut

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
10
3.2 Install the Cabinet Frames
3.2.1 Install the first cabinet frame from the lower middle part. Use a spirit
level to adjust the flatness and verticality and then secure the cabinet frame to
the connection plates on the rails.
Fixed the Cabinet Frames with the Cabinet Connection Plates
M8*20mm Screws
4PCS/Cabinet Frame
1-3
1-3

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
11
3.2.2 Repeat the above steps to install other cabinets from bottom up, from the
middle to the sides. Cabinets frame must be installed following the number.
1-1
1-2
1-3
1-4

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
12
Use the M6*6 screws to fix between the two cabinets frames. The hammer drill
or the Allen key shall help to lock the screws.
Please do not fix the screws between the connection plates and cabinets
frames too tight for future adjustment. All the red circled parts are adjusting
points.
Ensure that the seam and flatness between cabinets frame conform to the
standard after each cabinet frame is installed. Otherwise, make some
adjustments.
M6*6mm Screws
5PCS/Cabinet
1-2
1-3
1-1
1-2
1-3
1-4
2-1
2-2
2-3
2-4
3-1
3-2
3-3
3-4
4-1
4-2
4-3
4-4

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
13
4. Connection the signal cables and power cables
The following two figures show the connection diagrams of UFP-F1.26 LED
screen. The resolution is 1080P. The signal cables are marked in green and the
power cables in red.
Cabling Diagram 1
Cabling Diagram 2

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
14
5. Install the LED Display Screen.
5.1 Install the first LED panel from the lower middle part.
Before start the steps, please wear the rubber gloves. To avoid the LED panels
to be bumped.
And notice that the LED panels must be installed carefully from the middle to
the sides, bottom up, row by row. Adjust the flatness after each row of panels
are installed.
1-3-1
1-3-2

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
15
5.2 When you remove the panels, please use the professional tools carefully.
For example the vacuum suction tools.
vacuum suction tools

Dongguan HCP Technology Co., Ltd
41041 Trimboli Way, #1761, Fremont, CA 94538, USA
16
Defective Phenomena Pictures Common Problems Solutions
The display screen is power off; Open the power supply.
The brightness is 0%; The brightness is 100%
The connection between the sending
box and display screen is broken
Connect the internet cable.
The screen has light line
The gap between the
cabinets is obvious
The flatness between the cabinets
are not good
Adjust the gap. Using the suction
tools
The power cable between the
cabinets isn't connected
Check the power supply if it is
normal(the green indicator
twinkling). If not, reconnect the cable
The signal cable is connected
wrongly
Check the receving cards work
normaly, reconnect the signal cable
according to the controlling system
operation
The calibration data in the screen is
missing
Install the panel and cabinet in order,
the confirm if it works normally
The installations of panel and
cabinet are wrong, not mount in
order
Reupload the relative calibration
data
The connection order of the network
cable is wrong;
Set up the Novastar control system,
open mapping fuction, follow the
order and reconnect the screen
The cabinet or panel order is wrong Change the connection.
The display disorder
No display or black on
the entire LED display
screen
No display on parts of the
entire LED display screen
The RGB display has spot
color
Trouble Shooting