Health GEAR Deluxe ITM 4800-A User manual

1
Deluxe Heat & Massage Inversion Table
Model ITM 4800-A
Photo may differ from actual product
CAUTION:
WARNING: DO NOT USE THIS
INVERSION TABLE WITHOUT A
PHYSICIAN’S APPROVAL
It is recommended that Inverting
upside down be supervised.
Do not let children use the
inversion table unsupervised.
Read all instructions carefully
before using.
Tighten all bolts before using
equipment.
Leave adequate space to
properly invert.
Questions/ Comments
PLEASE DO NOT CONTACT THE
STORE FOR PARTS OR
SERVICE QUESTIONS
Extreme Products Group is committed to
providing the very best of quality and
customer satisfaction for all of the
products we distribute. If for any reason ,
you are dissatisfied with the product you
have purchased or need assistance in any
way, please do not hesitate to contact our
knowledgeable support staff as follows:
Phone:[phone]
Email: [email protected]
Web: www.extremeproductsgroup.com
Mon.-Fri 9:00 am – 5:00 pm Phoenix Time
S
Ver 101514

2
BEFORE BEGINNING ASSEMBLY…
Take a few moments to familiarize yourself with the specific parts and hardware included with your
product. Make sure all the parts and hardware are included in the carton and examine them for any
damage that may have occurred in transport. Some parts may be pre-assembled and pre-installed.
CAUTION
WARNING:
BEFORE STARTING ANY INVERSION PROGRAM, CONSULT YOUR PHYSICIAN.
Read all instructions very carefully before using equipment
Tighten all bolts securely before using equipment
Product Warranty
Limited Liability
Extreme Products Group warrants that this product will be free from defects in materials and workmanship
for a period of 1 year on the frame, and 90 days on all other parts from date of purchase. This warranty
applies only to the original purchaser when purchase of the product is from an authorized retailer and is for
personal or household use, but not when the sale is for commercial use. This warranty is not transferable.
EXCEPT FOR THE LIMITED EXPRESS WARRANTY STATED HEREIN, EXTREME PRODUCTS GROUP
DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Extreme Products Group, will not be liable for any loss or damage, including incidental or consequential
damages of any kind, whether based upon warranty, contract or negligence and arising in connection with
the sale, use or repair of the product.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
In the event of failure of this product to conform to this warranty during the warranty period, please call
Extreme Products Group Customer Service Number at 623-888-6379 for assistance in the repair or
replacement of the product or any covered part. Extreme Products Group will repair or replace, at its own
option, the product or any covered part, except that this warranty does not cover damage caused by
accident ( including transit) , or repairs or attempted repairs by any person not authorized by Extreme
Products Group, or by vandalism, misuse, abuse, or alteration. The Warranty Period is based on the
purchase date of the product validated by the Authorized Retailers Register Receipt, or valid copy of
transaction statement. Shipping and Handling is not included. By continuing with the assembly and use of
this products acknowledges your understanding of the Warnings and Warranty Guidelines stated above.
If you require technical support under this warranty, please call Customer Service at ( 623-888-6379).
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site at :
www.extremeproductsgroup.com

3
Parts Listing
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
Part# Description QTY Part# Description QTY
01 Base-frame-FRONT 1 26 Ball Pin- Φ8*64 1
02 Base-frame-REAR 1 27 Ball Pin-ø8 1
03 Backrest Support Tube 1 28 Spring 1
04 Body Height Adjustment Tube 1 29 Incline Adjustment Bolt 1
05 Adjustable Leg Hold Tube 1 30 Height Adjustment Knob 1
06 Foot Rest Plate 1 31 Leg Tube Adjustment Knob 1
07 Leg Tube-REAR 1 32 Square End Cap 6
08 Handlebar-RIGHT 1 33 Round End Cap-for handlebars 2
09 Handlebar-LEFT 1 34 Round End Caps 4
10L Connecting Bracket-LEFT 1 35 Square End Cap-for Part4 1
10R Connecting Bracket-RIGHT 1 36 Plastic Spacer 4
11 Hexagonal Bolt-M8*50 1 37 Plastic Round End-cap 2
12 Bolt-M8x60mm 2 38 Plastic Washer-ø20xø9.5x2.0 4
13 Bolt-M8x55mm 4 39 Stopper 1
14 Bolt-M8x30mm 6 40 Base Frame End Caps 4
15 Bolt-M8x20mm 4 41 Oval End Caps-Foot Rest 2
16 Bolt-M8x50mm 1 42 Foam leg Rollers 4
17 Hexagonal Bolt M8x15mm 3 43 Handlebar Grip 2
18 Hexagonal Bolt-M8x20mm 2 44 Backrest Pad 1
19 Bolt-M6x40mm 1 45 Head Pad 1
20 Flat Washer ø16xø8.5x1.5 21 46 Hand Controller 1
21 Washer ø12xø6.5x1.2 1 47 Power Adaptor 1
22 Nut M8 11 48 Heat & Massage Lumbar Pad 1
23 Nut M6 1 49 Wrench-#13/#17 2
24 Round Spring Insert 1 50 Hex Wrenches 1
25 Metal Bushing for Rear Leg Tube 1 51 End Cap 1

4
Exploded View
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com

5
Step 1- Unfold Frame
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
Carefully remove Base Frame from carton, and unfold.
Insert safety pin(26) into right side of frame
Note Front, Rear, Right and Left Sides for further
assembly
Insert safety
pin(26)

6
Step 2- Handlebar Assembly
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
TIGHTEN ALL BOLTS AT THIS TIME
STEP 2 ( Cont)
Attach the Handlebar Right (08) to the Base frame Rear(01)
using 2 Bolts (13), 2 Washers (20), and 2 Nuts (22). Use
Bolt (11) and Flat Washer (20) to fix the Base frame
Rear(01) .Repeat for Handlebar Left (02) except there will
not be a part 11 or 20 for this side.

7
Step 3- Backrest Assembly to Base Frame
STEP 3 Connecting Backrest Pad & Assembly to Frame
Attach the Completed Backrest Pad Assembly to the Base frame Unit
using Bolts (15), Flat Washers (20) and Lock Nuts (22) as shown
NOTE: TIGHTEN ALL BOLTS AT THIS TIME
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
Note: Rotational Side
Brackets must face
DOWN toward floor
Lift Entire Bed Assembly
UP into Rotational
Brackets
And Secure with Bolts,
Nuts, and Washers

8
STEP 4 -Body Height Adjustment Tube and Rollers
A- Install Foot Rest
Plate (6) into Height
Adjustment Tube (4)
using Hexagonal Bolts
(17), & Flat Washers
(20)
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
TIGHTEN ALL BOLTS AT THIS TIME
B- Lift out front roller tube (31) from Height
Adjustment Selector Tube (5) and position as
shown. Slide Foam Rollers (42) over front Tube (5)
and insert Plastic End Caps (34)
C- Insert Rear Foam Roller Tube (7) through Height
Adjustment Tube (4) and secure with Bolt (16),
Metal Spacer (25), Washer (20) and nut (22). Slide
Foam Rollers (42) over Rear Tube (7) and insert
End Caps (34) . Make sure Leg Tube Adjustment
Knob (31) is properly connected to Height
Adjustment Tube (4) and functions properly

9
STEP 5 -Final Assembly
Slide Completed Height Adjustment Tube and Foot Rest
Assembly (4) into Backrest Support Tube (3) and lock into
place using Height Adjustment Knob (30) and Safety Pin
(27)
Note: This product is designed with a Maximum User
Weight of 300 LBS.
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
NOTE: TIGHTEN ALL BOLTS AT THIS TIME

10
Heat / Massage Pad and Head Pad
Assembly to Backrest Pad
Step 6 Connecting Head Pad and Heat/Massage Lumbar Pad
Attach the Heat / Massage Lumbar Pad(48)and the Head Pad(45) to
Backrest Pad(47) in Desired Position using Velcro. Controller(46) can be
stored in Right Side Pocket of Backrest Pad(44) for easy access.
Note: Please pay careful attention that the power cord is not squeezed or
damaged by the inversion table when using it.
Make Sure All Nuts
Bolts and Screws are
Completely Tightened
Before Use.
Final Assembly

11
PRECAUTIONS
WARNING: 300 LB WEIGHT CAPACITY
To reduce the risk of serious injury, read all important precautions
instructions and warnings in this manual before using the Inversion
System. Extreme Products Group assumes no responsibility for
personal injury or property damage sustained by or through the use
of the Inversion System.
DO NOT USE THIS INVERSION TABLE WITHOUT A PHYSICIAN’S
APPROVAL, OR IF YOU HAVE ANY OF THE FOLLOWING
CONDITIONS
(this list is for reference only, it is not an exhaustive listing):
Pregnancy; Hiatal Hernia, ventral hernia; glaucoma, Retinal Detachment or
Conjunctivitis; High Blood Pressure, Hypertension, recent Stroke or Transient Ischemic
Attack; heart or Circulatory Disorders for which you are being treated; Spinal Injury;
Cerebral Sclerosis; Acutely Swollen Joints; Bone Weakness ( Osteoporosis ), recent
unhealed fractures, medulary pins and surgically implanted orthopedic supports; the
use of anticoagulants, including high doses of aspirin; Middle Ear Infections, Over
weight or Extreme Obesity.
IF YOUR PHYSICIAN PERMITS YOU TO USE INVERSION THERAPY,
DO SO UNDER THEIR DIRECTION AND HAVE OUR GUIDELINES
APPROVED BY YOUR PHYSICIAN BEFORE USE
DO NOT LET CHILDREN USE THE INVERSION TABLE
UNSUPERVISED.
THERE ARE CERTAIN PEOPLE WHO SHOULD NEVER INVERT. IF
YOU THINK YOU BELONG TO THIS MINORITY, PLEASE CHECK WITH
YOUR PHYSICIAN BEFORE USING THIS INVERSION TABLE.
INSURE THAT ALL NUTS, BOLTS, AND SCREWS ARE COMPLETELY
TIGHTENED BEFORE USING THIS PRODUCT.
SECURE YOUR ANKLES AND LOCK PULL PIN IN PLACE BEFORE
INVERTING.
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com

12
Controller Instruction
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com

13
USAGE GUIDELINES
INVERSION SELECTOR PIN
Familiarize yourself with the
Inversion Selector Pin located
on the Right Side of the
Inversion Table. The positioning
of the pin will determine the
degree of Inversion that you are
comfortable with.
The 3 selections are:
20- Slight Inversion
40-Moderate Inversion
60- Enhanced Inversion
NOTE: IT IS STRONGLY RECOMMENDED THAT SOMEONE BE
WITH YOU DURING INVERSION. ALTHOUGH THE INVERSION
TABLE IS EASY TO USE, HAVING SOMEONE NEARBY TO
“SPOT” YOU WILL PROVIDE EXTRA SAFETY AND SUPPORT TO
THE INVERSION PROCESS. START WITH 20 DEGREE SETTING
Body Height Adjustment:
Before Starting, insure that the
Inversion Table is at the correct
settings to match your height. ( This
is indicated on the Height
Adjustment Selector in both Inches
and Centimeters.
As each individual’s body type is
different, you will need to find the
correct balance settings for your
specific body type by adjusting the
selector up or down to obtain the
proper balance
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com
Photo may be slightly
different that actual product

14
USAGE GUIDELINES- Securing Feet and Ankles
WARNING: ALWAYS WEAR ATHLETIC SHOES WITH LACES TIGHT
TO HELP SECURE YOUR FEET IN THE INVERSION SYSTEM, AND FOR
FOOT PROTECTION WHILE EXERCISING.
ALWAYS MAKE SURE THAT THE ANKLE LOCK IS SECURED SNUGLY
AGAINST YOUR ANKLES AND THAT THE LONG KNOB IS FULLY
TIGHTENED BEFORE YOU USE THE INVERSION SYSTEM
Step 1- Expand the front
rollers by pulling up on the
Leg Tube Adjustment
Knob (31)
Step 2- Slide
Feet under
Foam Rollers
Step 3- Contract the front
rollers snugly over feet by
releasing the Leg Tube
Adjustment Knob and making
sure it “Locks” into place.
WARNING: LEGS AND ANKLES MUST BE SUCURELY LOCKED
INTO PLACE BEFORE INVERTING. DO NOT INVERT IF THIS
LOCKING MECHANISM IS NOT FUNCTIONING PROPERLY
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com

15
USAGE GUIDELINES
Finding the Proper Height and Weight Adjustment
With head flat on back pad, slowly raise one arm up
toward the ceiling. If the bed starts to invert backward,
the height adjustment should be correct.
If the bed does not start to invert, adjust the center slider
arm upward one position at a time, until the bed starts to
invert backward. Remember to use very slow arm
movements.
By raising both hands over your head, the
Inversion Table should now invert to a greater
degree, provided that you are comfortable with
the side adjustment knob being set to 20 or higher.
Note: It is recommended that beginners use the
setting marked 20 for Partial Inversion.
With proper supervision, and provided you are
comfortable with the side adjustment knob
being set to 40 or 60, the Inversion Table will
now allow for a more complete Inversion
position.
CAUTION: BY LOWERING THE HANDS BACK TO THE
STARTING POSITION, THE INVERSION TABLE SHOULD
REVERT BACK TO THE UPRIGHT POSITION. IF IT DOES
NOT, USE THE BUILT IN SIDE HANDLEBARS TO PULL
YOURSELF BACK UP AND RE-ADJUST THE CENTER
SLIDER TO ACCOMMODATE YOUR BODY WEIGHT AND
TYPE.
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com

16
Health Gear is a licensed Trademark and
Distributed By:
Extreme Products Group
6635 W. Happy Valley Rd
Suite A-104, #213
Phoenix, AZ 85310
Technical Support: 623-888-6379
Fax: [phone]
Email: [email protected]
For All parts requests, please do not call our
Technical service number but visit our web
site at www.extremeproductsgroup.com
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site: www.extremeproductsgroup.com