Health GEAR ITM 6000 User manual

1
Deluxe Heat & Massage Inversion Table
Model ITM 6000
Photo may differ from actual product
CAUTION:
WARNING: DO NOT USE THIS
INVERSION TABLE WITHOUT A
PHYSICIAN’S APPROVAL
It is recommended that Inverting
upside down be supervised.
Keep children away
Read all instructions carefully
before using.
Tighten all bolts before using
equipment.
Leave adequate space to
properly invert.
Questions/ Comments
PLEASE DO NOT CONTACT THE
STORE FOR PARTS OR
SERVICE QUESTIONS
Extreme Products Group is committed to
providing the very best of quality and
customer satisfaction for all of the products
we distribute. If for any reason , you are
dissatisfied with the product you have
purchased or need assistance in any way,
please do not hesitate to contact our
knowledgeable support staff as follows:
Phone:[phone]
Mon.-Fri 9:00 am – 5:00 pm Phoenix Time
S
012315

2
BEFORE BEGINNING ASSEMBLY…
Take a few moments to familiarize yourself with the specific parts and hardware included with your
product. Make sure all the parts and hardware are included in the carton and examine them for any
damage that may have occurred in transport. Some parts may be pre-assembled and pre-installed.
CAUTION
WARNING:
BEFORE STARTING ANY INVERSION PROGRAM, CONSULT YOUR PHYSICIAN.
Read all instructions very carefully before using equipment
Tighten all bolts securely before using equipment
Product Warranty
Limited Liability
Extreme Products Group warrants that this product will be free from defects in materials and workmanship
for a period of 1 year on the frame, and 90 days on all other parts from date of purchase. This warranty
applies only to the original purchaser when purchase of the product is from an authorized retailer and is for
personal or household use, but not when the sale is for commercial use. This warranty is not transferable.
EXCEPT FOR THE LIMITED EXPRESS WARRANTY STATED HEREIN, EXTREME PRODUCTS
GROUP DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING BUT NOT
LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Extreme Products Group, will not be liable for any loss or damage, including incidental or consequential
damages of any kind, whether based upon warranty, contract or negligence and arising in connection with
the sale, use or repair of the product.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
In the event of failure of this product to conform to this warranty during the warranty period, please call
Extreme Products Group Customer Service Number at 623-888-6379 for assistance in the repair or
replacement of the product or any covered part. Extreme Products Group will repair or replace, at its own
option, the product or any covered part, except that this warranty does not cover damage caused by
accident ( including transit) , or repairs or attempted repairs by any person not authorized by Extreme
Products Group, or by vandalism, misuse, abuse, or alteration. The Warranty Period is based on the
purchase date of the product validated by the Authorized Retailers Register Receipt, or valid copy of
transaction statement. Shipping and Handling is not included. By continuing with the assembly and use of
this products acknowledges your understanding of the Warnings and Warranty Guidelines stated above.
If you require technical support under this warranty, please call Customer Service at ( 623-888-6379).
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site for
more information.

3
Parts Listing
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
Part# Description QTY Part# Description QTY
01 Base-frame-FRONT 1 26 Ball Pin-ø8 1
02 Base-frame-REAR 1 27 Incline Adjustment Bolt 1
03 Backrest Support Tube 1 28 Height Adjustment Knob 1
04 Body Height Adjustment Tube 1 29 Square End Cap 6
05 Adjustable Leg Hold Tube 2 30 Round End Cap-for handlebars 2
06 Foot Rest Plate 1 31 Round End Caps 4
07 Leg Tube Adjustment Knob 1 32 Plastic Spacer 4
08 Handlebar-RIGHT 1 33 Plastic Round End-cap 2
09 Handlebar-LEFT 1 34 Plastic Washer-
ø 20x ø 9.5x2.0 4
10L Connecting Bracket-LEFT 1 35 Stopper 1
10R Connecting Bracket-RIGHT 1 36 Base Frame End Caps 4
11 Hexagonal Bolt-M8*50 1 37 Oval End Caps-Foot Rest 2
12 Bolt-M8x60mm 2 38 Foam leg Rollers 4
13 Bolt-M8x55mm 4 39 Handlebar Grip 2
14 Bolt-M8x30mm 6 40 EVA Pad 1
15 Bolt-M8x20mm 4 41 Back Pad 1
16 Bolt-M8x42mm 2 42 Power Adaptor 1
17 Hexagonal Bolt M8x50mm 2 43 Hand Controller 1
18 Hexagonal Bolt-M8x20mm 2 44 Wrench-#13/#17 2
19 Bolt-M8x35mm 1 45 Hex Wrenches 1
20 Flat Washer
ø 16x ø 8.5x1.5 22
21 Heat & Massage Lumbar Pad 1
22 Nut M8 15
23 Plastic Bushing ø22 2
24 Plastic Cover for Square Tube 1
25 Ball Pin- Φ8*64 1

4
Exploded View
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
* For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT. Please visit our web site:
www.extremeproductsgroup.com

5
Step 1- Unfold Frame
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
Step 1-Carefully remove Base Frame from carton, and
unfold.
Insert safety pin(25) into right side of frame
Note Front, Rear, Right and Left Sides for further
assembly
Insert safety pin()
To view an assembly video of this product, please visit our web site at:
www.extremeproductsgroup.com
Front Rear
Right
Left

6
Step 2- Handlebar Assembly
STEP 2
Front
Reinforcement Bolt-11
Note: Right Handlebar
has Built in Bracket
Rear
Left
Right
Attach the Right Handlebar (08) to the Right Side Base Frame using
2 Bolts (13), 2 Washers (20), and 2 Nuts (22). Use Bolt (11) and Flat
Washer (20) to reinforce the Incline Adjustment Bracket to the Base
Frame.
Attached the Left Handlebar(9) to the Left Side Base Frame using 2
Bolts (13) 2 Washers (20) and 2 Nuts (22).
Attached Incline Adjustment Bolt through # 20 selection hole at this
time.
TIGHTEN ALL BOLTS AT THIS TIME
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.

7
Step 3- Backrest Assembly to Base Frame
STEP 3 Connecting Backrest Pad & Assembly to Frame
Attach the Completed Backrest Pad Assembly to the Base frame Unit
using Bolts (15), Flat Washers (20) and Lock Nuts (22) as shown.
NOTE: TIGHTEN ALL BOLTS AT THIS TIME
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
Note: Rotational Side
Brackets must face
DOWN toward floor
Lift Entire Bed Assembly UP
into Rotational Brackets
And Secure with Bolts, Nuts,
and Washers

8
STEP 4 -Body Height Adjustment Tube and Rollers
A- Install Foot Rest Plate (06) onto Height
Adjustment Tube (04) using Hexagonal Bolts
(17), Flat Washers (20) and Lock Nuts (22).
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
NOTE: TIGHTEN ALL BOLTS AT THIS TIME
B- Insert Rear Foam Roller Tube (05) through
Height Adjustment Tube (04) and secure with Bolt
(16), Washer (20) and nut (22). Slide Foam Rollers
(38) over Rear Tube (05) and insert End Caps (31) .
C- Insert Front Foam Roller Tube (05) through
Height Adjustment Tube (04) and secure with
Bolt (16) Washer (20) and nut (22). Slide Foam
Rollers (38) over Rear Tube (05) and insert End
Caps (31) .
Make sure Leg Tube Adjustment Knob is properly
connected to Height Adjustment Tube (04) and
functions properly

9
STEP 5 -Final Assembly
Slide Completed Height Adjustment Tube and Foot Rest
Assembly into Backrest Support Tube and lock into place
Using Height Adjustment Knob
Use Knob Bolt (28) to additional secure Height Adjustment
Tube in place when desired Height Adjustment is obtained.
Additional Locking Pin (26) is provided and should be used
for additional safety and security.
Note: This product is designed to adjust from 5’1” to 6’6”
with a Maximum User Weight of 300 LBS.
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
NOTE: TIGHTEN ALL BOLTS AT THIS TIME
NOTE: It is very important that
the side rotational brackets be
pointing down in this position
otherwise the inversion table
will not function properly and
may cause injury

10
Step 6-Heat/Massage Pad Backrest Pad
Step 6 Connecting Massage/Heat Pad to Backrest Pad
Attach the Heat/Massage Pad (21) to Backrest Pad(41) using 2 straps
though upper hole and 2 lower straps through lower hole. Once straps are
connected, tighten strap to secure heat /massage pad
NOTE: Controller(43) can be stored in Velcro Pocket of Backrest Pad
( at Bottom) for easy access.
Note: Please pay attention to the power cord not be squeezed by the
inversion table when using it.
Make Sure All Nuts Bolts and Screws are Completely
Tightened Before Use.
Final Assembly
Upper Hole
Lower Hole
Note: Controller
Pocket towards
bottom
READ ALL WARNINGS BEFORE USING THIS PRODUCT
To view an assembly video of this product, please visit our web site.
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.

11
PRECAUTIONS
WARNING: 300 LB WEIGHT CAPACITY
To reduce the risk of serious injury, read all important precautions
instructions and warnings in this manual before using the Inversion
System. Extreme Products Group assumes no responsibility for personal
injury or property damage sustained by or through the use of the Inversion
System.
DO NOT USE THIS INVERSION TABLE WITHOUT A PHYSICIAN’S
APPROVAL, OR IF YOU HAVE ANY OF THE FOLLOWING CONDITIONS
(this list is for reference only, it is not an exhaustive listing):
Pregnancy; Hiatal Hernia, ventral hernia; glaucoma, Retinal Detachment or
Conjunctivitis; High Blood Pressure, Hypertension, recent Stroke or Transient Ischemic
Attack; heart or Circulatory Disorders for which you are being treated; Spinal Injury;
Cerebral Sclerosis; Acutely Swollen Joints; Bone Weakness ( Osteoporosis ), recent
unhealed fractures, medulary pins and surgically implanted orthopedic supports; the
use of anticoagulants, including high doses of aspirin; Middle Ear Infections, Over
weight or Extreme Obesity.
IF YOUR PHYSICIAN PERMITS YOU TO USE INVERSION THERAPY, DO SO
UNDER THEIR DIRECTION AND HAVE OUR GUIDELINES APPROVED BY
YOUR PHYSICIAN BEFORE USE
DO NOT LET CHILDREN USE THE INVERSION TABLE UNSUPERVISED.
THERE ARE CERTAIN PEOPLE WHO SHOULD NEVER INVERT. IF YOU
THINK YOU BELONG TO THIS MINORITY, PLEASE CHECK WITH YOUR
PHYSICIAN BEFORE USING THIS INVERSION TABLE.
INSURE THAT ALL NUTS, BOLTS, AND SCREWS ARE COMPLETELY
TIGHTENED BEFORE USING THIS PRODUCT.
SECURE YOUR ANKLES AND LOCK PULL PIN IN PLACE BEFORE
INVERTING.
USE CAUTION WHEN PLACING YOUR HANDS ON THE HANDLEBARS OR
ON THE ROTATIONAL BAR AREA.
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.

12
Controller Instruction
Note:
For Safety DO NOT use more than 30 minutes per session.
If the unit is on and unattended it will auto shut off at 15 minutes.
Connect the product with power source by 12V adaptor and the indicator light
of "POWER" will blink into standby.
Press the "POWER" button to
start the massage function,
the power indicator light will
stop blinking, the massage
function will start in AUTO
mode with 2nd level intensity
Press "AUTO" button
and the massage
modes and intensities
will change
automatically.
In Auto or Manual modes
Press "INTENSITY"
button to change the
intensity of massage
function, there are 5 levels,
circulating a sequence of
2-3-4-5-1-2. The indicator
light of "INTENSITY" is
blinking faster when
intensity is higher.
Press "HEAT" button to
start the heat function.
The indicator light of
"HEAT" is red. Press
again to stop the heat
function, the indicator light
is out.
Press " MANUAL" button to
cancel the auto mode and
start the manual mode.
Press "MANUAL" button to
change the massage
modes. The indicator light
of "MANUAL" is red.

13
USAGE GUIDELINES
INVERSION SELECTOR PIN
Familiarize yourself with the
Inversion Selector Pin located
on the Right Side of the
Inversion Table. The positioning
of the pin will determine the
degree of Inversion that you are
comfortable with.
The 3 selections are:
20- Slight Inversion
40-Moderate Inversion
60- Enhanced Inversion
NOTE: IT IS STRONGLY RECOMMENDED THAT SOMEONE BE
WITH YOU DURING INVERSION. ALTHOUGH THE INVERSION
TABLE IS EASY TO USE, HAVING SOMEONE NEARBY TO “SPOT”
YOU WILL PROVIDE EXTRA SAFETY AND SUPPORT TO THE
INVERSION PROCESS.
Body Height Adjustment:
Before Starting, insure that the
Inversion Table is at the correct
settings to match your height. ( This
is indicated on the Height
Adjustment Selector in both Inches
and Centimeters.
As each individual’s body type is
different, you will need to find the
correct balance settings for your
specific body type by adjusting the
selector up or down to obtain the
proper balance
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
Photo may be slightly
different that actual product

14
USAGE GUIDELINES- Securing Feet and Ankles
WARNING: ALWAYS WEAR ATHLETIC SHOES WITH LACES TIGHT
TO HELP SECURE YOUR FEET IN THE INVERSION SYSTEM, AND FOR
FOOT PROTECTION WHILE EXERCISING.
ALWAYS MAKE SURE THAT THE ANKLE LOCK IS SECURED SNUGLY
AGAINST YOUR ANKLES AND THAT THE LONG KNOB IS FULLY
TIGHTENED BEFORE YOU USE THE INVERSION SYSTEM
Step 1- Expand the front
rollers by pulling up on the
Leg Tube Bar knob and
Release Forward.
Carefully Step on to the
Foot Rest Plate
Step 2- Slide Feet under Foam
Rollers and rest heels against
rear Foam Rollers. Pull up on
top button knob and slowly pull
lever back so front rollers are
secure against legs.
Step 3- Adjust the front rollers
tight against legs and secure
legs and ankles in place by
making sure leg assembly
“LOCKS” into place.
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.
WARNING: LEGS AND ANKLES MUST BE
SUCURELY LOCKED INTO PLACE BEFORE
INVERTING. DO NOT INVERT IF THIS LOCKING
MECHANISM IS NOT FUNCTIONING PROPERLY
Actual Product May Differ From Photo

15
USAGE GUIDELINES
Finding the Proper Height and Weight Adjustment
With head flat on back pad, slowly raise one arm up
toward the ceiling. If the bed starts to invert backward,
the height adjustment should be correct.
If the bed does not start to invert, adjust the center slider
arm upward one position at a time, until the bed starts to
invert backward. Remember to use very slow arm
movements. ( Note: if you invert back too quickly, your
body is too high on the unit and should be lowered by
adjusting the Height Selector accordingly)
By raising both hands over your head, the
Inversion Table should now invert to a greater
degree, provided that you are comfortable with
the side adjustment knob being set to 20 or higher.
Note: It is recommended that beginners use the
setting marked 20 for Partial Inversion and that
someone be with you during the inversion process
With proper supervision, and provided you are
comfortable with the side adjustment knob
being set to 40 or 60, the Inversion Table will
now allow for a more complete Inversion
position.
CAUTION: BY LOWERING THE HANDS BACK TO THE
STARTING POSITION, THE INVERSION TABLE SHOULD
REVERT BACK TO THE UPRIGHT POSITION. IF IT DOES
NOT, USE THE BUILT IN SIDE HANDLEBARS TO PULL
YOURSELF BACK UP AND RE-ADJUST THE CENTER
SLIDER TO ACCOMMODATE YOUR BODY WEIGHT AND
TYPE.
Actual Product May Differ From Photo
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.

16
Health Gear is a licensed Trademark and
Distributed By:
Extreme Products Group
6635 W. Happy Valley Rd
Suite A-104, #213
Phoenix, AZ 85310
Technical Support: 623-888-6379
Fax: [phone]
For All parts requests, please do not call
our Technical service number but visit our
web site.
*For Any Parts Required, DO NOT CALL TECHNICAL SUPPORT.