HearthSong Quad Shootout Quick setup guide

#733537 | Ages 6+
Adult assembly required.
41"L x 31"W x 65"H
Takes 1 adult to assemble.
Includes:
Basketball Set
Quad Shootout Folding
Safety and Assembly Instructions
WARNING:
CHOKING HAZARD—Small parts.
Not for children under 3 yrs.
#1 (x 1)
Upper target board
#2 (x 1)
Lower rims #3 (x 7) #4 (x 4)
#5 (x 2) #6 (x 2)
#7 (x 1)
Jointed pole
#8 (x 1)
Jointed pole
#9 (x 1)
Jointed pole
#10 (x 1)
Jointed pole #11 (x 2)
#12 (x 1)
Jointed pole
#13 (x 1)
Jointed pole
#14 (x 1)
Clip-on piece
#15 (x 2)
Clip-on piece
#16 (x 2)
Clip-on piece
#17 (x 4) #18 (x 1) #19 (x 6) #20 (x 1)

Note:
1. Find a clean, level surface to begin the assembly of your basketball stand.
2. Remove all of the contents from the box and check that you have all of the parts shown on the parts list before you begin
assembly. Note: some parts may be pre-installed or pre-assembled.
3. Some gures or drawings may not look exactly like your product. Please read and understand the text before beginning each
assembly step.
4. While assembling, please note any warning labels on the parts.
5. After or during the assembly, if you nd the stand uneven or wobbly, please ensure that all the pipes and joints are secured
tightly.You also can rotate the pipes a little to settle this problem.
6. When assembling clip-on parts #14, 15, and 16, make sure they are level.
7. The basketball stand is designed for indoor use.
8. Do not hang on the basketball stand.
9. Periodically inspect the basketball stand for any broken or excessively worn pieces. Do not use if you notice any damage.
(continued on next page)

Assembly:
Step A: Parts #5, 7, and 8 may be adjusted for height. During initial assembly, extend the pipes
to full position, and release the spring lock buttons to secure in place.
#5
#5
#7
#8
Step B: Assemble all the parts of rear supporting frame as shown in the gure below. Please note, the sleeves of part #17 should
be pre-assembled onto the pipe of parts #5 and 11.Tip: Be sure to set up #9 and 10 so that connectors are facing inwards as
shown in image below.
(continued on next page)
#5
#5
#17
#17
#12
#13
#3
#3
#3
#3
#3
#4
#9
#10
#11 #11
#7
#8
#4
#4
#4
#17
#17
Watch the
assembly video at
HearthSong.com

Step C: Assemble the front support frame as shown
in the gure.
Step E: Using hook and loop strips, hang the net from the
middle pole #3 and attach to the front poles #3. Attach
the net to both sides of the frame. Attach to the top of the
frame with one hook and loop strip. Next, attach lower
rim #2 to parts #7 and 8, lining up the side with the push
button to the hole in #7. Before attaching, it is helpful to
slip the sides of the pole through the net. Finally, hang the
target board using hook and loop strips.
(continued on next page)
#6
#6
#3
#3
Step D: Join the front and rear supporting frames by
carefully pressing the clip-on parts #14, 15, and 16 onto
the poles of the frame as shown in the gure.
#16
#15
#15
#14
#16
#1
#2
#18

Step 1: Remove the lower rim #2 and all clip-on pieces #14, 15, and 16 from the frame. Fold the upper baskets at a 90 degree
angle to top. Adjust all spring lock buttons to the lowest position to collapse the pipes.
Step 2: Following the steps shown in the gure, pull the sleeves out from the joints (location of #7 and 8) and fold the pipes
combo backward.
(continued on next page)
Folding Steps:
#16
#16
#2
#15
#15
#14
#1
#3
#2
#4
#5#6
#7#8

Step 3: Using the gure below for guidance, pull up on all joints and fold pipes as shown in the images.
Step 4: Lay the front frame at against the rear frame. Pull the upper sleeves outwards from the joint (location of #15 and 16)
and fold the pipes combo downwards at a 90 degree angle.
#9
#10
A
B
C
D
#11
#12
#13
#14
#15
#16
#733537 Conforms to ASTM F963. Made in China. ©HearthSong®2020. Madison, VA 22727. 1-800-533-4397 HearthSong.com